I just got a SanDisk CRUZER 256MB USB memory thingy. It no workey! The USB is on a VIA 8235 chip if that matters. Could some of you gurus take a look at these messages and give me a clue about what I need to do to get this device working. I suspect that I'm missing a module, but I can't figure out what I need. Sorry about the size of this messages. I've trimmed out all the stuff that seemed irrelevant, but I didn't want to lose something important. Thanks, John Dec 22 20:11:21 localhost kernel: usb.c: registered new driver usbdevfs Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hub Dec 22 20:11:21 localhost kernel: usb-uhci.c: $Revision: 1.275 $ time 16:47:59 Dec 21 2003 Dec 22 20:11:21 localhost kernel: usb-uhci.c: High bandwidth mode enabled Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 11 for device 00:10.0 Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11 Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered, assigned bus number 1 Dec 22 20:11:21 localhost kernel: hub.c: USB hub found Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 3 for device 00:10.1 Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 3 Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered, assigned bus number 2 Dec 22 20:11:21 localhost kernel: hub.c: USB hub found Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 5 for device 00:10.2 Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 5 Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered, assigned bus number 3 Dec 22 20:11:21 localhost kernel: hub.c: USB hub found Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected Dec 22 20:11:21 localhost kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: PCI device 1106:3104 Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: irq 10, pci mem e1bba000 Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered, assigned bus number 4 Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4 Dec 22 20:11:21 localhost kernel: hub.c: USB hub found Dec 22 20:11:21 localhost kernel: hub.c: 6 ports detected Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hiddev Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hid Dec 22 20:11:21 localhost kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx> Dec 22 20:11:21 localhost kernel: hid-core.c: USB HID support drivers Dec 22 20:11:21 localhost kernel: hub.c: connect-debounce failed, port 2 disabled Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.3-2, assigned address 2 Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod 0x781/0x8185) is not claimed by any active driver. Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.2-1, assigned address 2 Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod 0xaec/0x3050) is not claimed by any active driver. Dec 22 20:11:21 localhost kernel: Initializing USB Mass Storage driver... Dec 22 20:11:21 localhost kernel: usb.c: registered new driver usb-storage Dec 22 20:11:21 localhost kernel: scsi1 : SCSI emulation for USB Mass Storage devices Dec 22 20:11:21 localhost kernel: Vendor: Generic Model: STORAGE DEVICE Rev: 1.25 Dec 22 20:11:21 localhost kernel: Type: Direct-Access ANSI SCSI revision: 02 Dec 22 20:11:21 localhost kernel: scsi2 : SCSI emulation for USB Mass Storage devices Dec 22 20:11:21 localhost kernel: Vendor: SOYO Model: USB Storage-CFC Rev: 0208 Dec 22 20:11:21 localhost kernel: Type: Direct-Access ANSI SCSI revision: 02 Dec 22 20:11:21 localhost kernel: USB Mass Storage support registered. Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0 Dec 22 20:11:21 localhost kernel: SCSI device sda: 512000 512-byte hdwr sectors (262 MB) Dec 22 20:11:21 localhost kernel: sda: Write Protect is off Dec 22 20:11:21 localhost kernel: sda: sda1 Dec 22 20:11:21 localhost kernel: sdb: Unit Not Ready, sense: Dec 22 20:11:21 localhost kernel: Current 00:00: sns = 70 2 Dec 22 20:11:21 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed. Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host = 0, driver = 08 Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2 Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: unable to read partition table Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense: Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2 Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed. Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host = 0, driver = 08 Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2 Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: unable to read partition table Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there is a disc in the drive. Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense: Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2 Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed. Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host = 0, driver = 08 Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2 Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0 Dec 22 20:11:22 localhost kernel: unable to read partition table Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there is a disc in the drive. Dec 22 20:11:22 localhost kernel: usb.c: registered new driver usblp Dec 22 20:11:22 localhost kernel: printer.c: v0.11: USB Printer Device Class driver Dec 22 20:12:24 localhost kernel: hub.c: USB device not accepting new address (error=-71) Dec 22 20:12:24 localhost kernel: usb.c: USB disconnect on device 00:10.3-2 address 2 Dec 22 20:12:24 localhost kernel: hub.c: new USB device 00:10.3-2, assigned address 3 Dec 22 20:12:27 localhost usb.agent[3564]: missing kernel or user mode driver usb-storage Dec 22 20:12:29 localhost kernel: usb-storage: host_reset() requested but not implemented Dec 22 20:12:39 localhost kernel: scsi: device set offline - command error recover failed: host 1 channel 0 id 0 lun 0 Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense: Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2 Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed. Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host = 0, driver = 08 Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2 Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0 Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0 Dec 22 20:12:39 localhost kernel: unable to read partition table Dec 22 20:12:39 localhost kernel: Device not ready. Make sure there is a disc in the drive. Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense: Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2 Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed. Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host = 0, driver = 08 Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2 Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0 Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512 bytes, disk size 1GB. Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0 Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0 Dec 22 20:12:39 localhost kernel: unable to read partition table
