On Wed, 2008-02-06 at 11:43 -0500, Gene Poole wrote: > A friend gave me a Exabyte 17D DLT tape library and I have a Buslogic > FlashPoint LW (BT-930) scsi-3 controller card. So I added them to a box > already running Fedora 8. > > Now I'm stuck. I tried google and didn't get anything that I can make sense > out of. and the only message I see are the following: > > Partial output from /sbin/lspci: > > 01:05.0 SCSI storage controller: BusLogic Flashpoint LT (rev 01) > > > Partial output from dmesg | more: > > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) > SCSI subsystem initialized > scsi0 : sata_nv > scsi1 : sata_nv > ata1: SATA max UDMA/133 cmd 0x00000000000109f0 ctl 0x0000000000010bf2 bmdma > 0x000000000001d800 irq 21 > ata2: SATA max UDMA/133 cmd 0x0000000000010970 ctl 0x0000000000010b72 bmdma > 0x000000000001d808 irq 21 > input: ImPS/2 Generic Wheel Mouse as /class/input/input2 > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata1.00: ATA-7: WDC WD3200AAJS-00RYA0, 12.01B01, max UDMA/133 > ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (not used) > ata1.00: configured for UDMA/133 > ata2: SATA link down (SStatus 0 SControl 300) > scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAJS-0 12.0 PQ: 0 ANSI: 5 > scsi2 : pata_amd > scsi3 : pata_amd > ata3: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma > 0x000000000001f000 irq 14 > ata4: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma > 0x000000000001f008 irq 15 > ata3.00: ATAPI: SONY DVD RW DRU-830A, SS25, max UDMA/66 > ata3.00: limited to UDMA/33 due to 40-wire cable > ata3.00: configured for UDMA/33 > ata4: port disabled. ignoring. > scsi 2:0:0:0: CD-ROM SONY DVD RW DRU-830A SS25 PQ: 0 ANSI: 5 > > I didn't see anything in /var/log/messages. > > During the boot I entered the Buslogic auto-config routines and it tells me > that the scsi controller ID is 7 and the tape library uses 2 ID's 0 and 1. > > After the reboot was complete I now see the following messages: > > BusLogic: FlashPoint Host Adapter detected at PCI Bus 1 Device 5 > BusLogic: I/O Address 0xCC00 PCI Address 0xFDEFF000, irq 16, but FlashPoint > BusLogic: support was omitted in this kernel configuration. > > > I entered the following command: > > sudo find / -name *BusLogic* > > Which returned: > > /lib/modules/2.6.23.9-85.fc8/kernel/drivers/scsi/BusLogic.ko > /lib/modules/2.6.23.14-107.fc8/kernel/drivers/scsi/BusLogic.ko > > Can the above be used in a 'insmod' command? Or what should I do? First, do an "lsmod" to see if the BusLogic driver is already loaded (it looks like it is from your message list). However, the Flashpoint version of it doesn't look like it was enabled (e.g. when the BusLogic driver was built, "CONFIG_SCSI_OMIT_FLASHPOINT" was set. That means you need to rebuild the driver. ---------------------------------------------------------------------- - Rick Stevens, Principal Engineer rstevens@xxxxxxxxxxxx - - CDN Systems, Internap, Inc. http://www.internap.com - - - - If your broker is so damned smart...why is he still working? - ----------------------------------------------------------------------
