A friend gave me a Exabyte 17D DLT tape library and I have a Buslogic FlashPoint LW (BT-930) scsi-3 controller card. So I added them to a box already running Fedora 8. Now I'm stuck. I tried google and didn't get anything that I can make sense out of. and the only message I see are the following: Partial output from /sbin/lspci: 01:05.0 SCSI storage controller: BusLogic Flashpoint LT (rev 01) Partial output from dmesg | more: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) SCSI subsystem initialized scsi0 : sata_nv scsi1 : sata_nv ata1: SATA max UDMA/133 cmd 0x00000000000109f0 ctl 0x0000000000010bf2 bmdma 0x000000000001d800 irq 21 ata2: SATA max UDMA/133 cmd 0x0000000000010970 ctl 0x0000000000010b72 bmdma 0x000000000001d808 irq 21 input: ImPS/2 Generic Wheel Mouse as /class/input/input2 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: WDC WD3200AAJS-00RYA0, 12.01B01, max UDMA/133 ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (not used) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAJS-0 12.0 PQ: 0 ANSI: 5 scsi2 : pata_amd scsi3 : pata_amd ata3: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001f000 irq 14 ata4: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001f008 irq 15 ata3.00: ATAPI: SONY DVD RW DRU-830A, SS25, max UDMA/66 ata3.00: limited to UDMA/33 due to 40-wire cable ata3.00: configured for UDMA/33 ata4: port disabled. ignoring. scsi 2:0:0:0: CD-ROM SONY DVD RW DRU-830A SS25 PQ: 0 ANSI: 5 I didn't see anything in /var/log/messages. During the boot I entered the Buslogic auto-config routines and it tells me that the scsi controller ID is 7 and the tape library uses 2 ID's 0 and 1. After the reboot was complete I now see the following messages: BusLogic: FlashPoint Host Adapter detected at PCI Bus 1 Device 5 BusLogic: I/O Address 0xCC00 PCI Address 0xFDEFF000, irq 16, but FlashPoint BusLogic: support was omitted in this kernel configuration. I entered the following command: sudo find / -name *BusLogic* Which returned: /lib/modules/2.6.23.9-85.fc8/kernel/drivers/scsi/BusLogic.ko /lib/modules/2.6.23.14-107.fc8/kernel/drivers/scsi/BusLogic.ko Can the above be used in a 'insmod' command? Or what should I do? Thanks, Gene Poole
