Hi David Walcroft! Scanning the thread it sounds like you have a DHCP server set up to run from Eth1 which is connected by a crossover cable to Eth0, which sets up to be 192.168.0.1 -- then when Eth1 tries to be 192.168.0.1 it cannot since that is already taken. If the above is correct you need to edit your DHCP server config files to create the network you describe (Eth0 ...2 -- Eth1...1). As a quick check you might try setting both ports to the separate fixed addresses and see if ping then works. The only other thing that occurs to me is that many of the error messages sound like those I would hear from SELinuix - are you running a security environment such as SELinux and is it in enforcing mode??! Good Hunting! Tod On 10/3/07, david walcroft <d_j_w46@xxxxxxxxxxxxxx> wrote: > Timothy Murphy wrote: > > david walcroft wrote: > > > > > >>>> Can someone tell how to get over this error please > >>>> > >>>> [david@reddwarf ~]$ sudo service network restart > >>>> Shutting down interface eth0: [ OK ] > >>>> Shutting down interface eth1: [ OK ] > >>>> Shutting down loopback interface: [ OK ] > >>>> Disabling IPv4 packet forwarding: net.ipv4.ip_forward = 0 > >>>> [ OK ] > >>>> SIOCGIFFLAGS: No such device > >>>> Bringing up loopback interface: [ OK ] > >>>> Bringing up interface eth0: > >>>> Determining IP information for eth0... done. > >>>> [ OK ] > >>>> Bringing up interface eth1: sysfs class device: Permission denied > >>>> Error, some other host already uses address 192.168.0.1. > >>>> > > > > How do eth0 and eth1 get their IP addresses? > > >From dhcp? > > > Eth0 is dhcp,Ethe1 is static 192.168.0.1 > > What does "ifconfig eth1" say? > > > [david@reddwarf ~]$ ifconfig eth1 > eth1 Link encap:Ethernet HWaddr 00:E0:4C:14:1B:09 > inet6 addr: fe80::2e0:4cff:fe14:1b09/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:3 errors:0 dropped:0 overruns:0 frame:0 > TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:747 (747.0 b) TX bytes:578 (578.0 b) > Interrupt:22 Base address:0x8c00 > > [david@reddwarf ~]$ > > What does "route" say? > > > [david@reddwarf ~]$ route > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > 121.208.32.0 * 255.255.248.0 U 0 0 0 eth0 > 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 > default 121.208.32.1 0.0.0.0 UG 0 0 0 eth0 > [david@reddwarf ~]$ > > What is in /etc/sysconfig/network-scripts/ifcfg-eth1? > > > # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ > DEVICE=eth1 > ONBOOT=yes > BOOTPROTO=none > HWADDR=00:e0:4c:14:1b:09 > NETMASK=255.255.255.0 > IPADDR=192.168.0.1 > GATEWAY=192.168.0.0 > TYPE=Ethernet > USERCTL=no > IPV6INIT=no > PEERDNS=yes > > [david@reddwarf ~]$ sudo ping -c 5 192.168.0.2 > PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data. > ping: sendmsg: Operation not permitted > ping: sendmsg: Operation not permitted > ping: sendmsg: Operation not permitted > ping: sendmsg: Operation not permitted > ping: sendmsg: Operation not permitted > > What do I do to get ping to work and is it part of this problem overall. > 192.168.0.2 is on the other end of my crossover cable > > Thanks david > > > > > > > > > > > > -- > fedora-list mailing list > fedora-list@xxxxxxxxxx > To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list >
