On Jan 11, 2006, at 1:41 AM, Gilboa Davara wrote:
On Tue, 2006-01-10 at 17:43 -0800, M. Barnabas Luntzel wrote:
Ever since I was upgraded (by smart) to 2.6.14, I have not been able
to boot any of these kernels. vmlinuz-2.6.13-1.1532_FC4 works fine so
I've at least had a working system. vmlinuz-2.6.14-1.1656_FC4 as well
as vmlinuz-2.6.14-1.1653_FC4 bomb out on boot with these messages:
Booting 'Fedora Core (2.6.14-1.1656_FC4)'
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /boot/vmlinuz-2.6.14-1.1656_FC4 ro root=LABEL=/ quiet
[Linux-bzimage, setup=0x1e00, size=0x178b66]
initrd /boot/initrd-2.6.14-1.1656_FC4.img
[Linux-initrd @ 0x37ec7000, 0x128125 bytes]
Uncompressing Linux... OK, booting the kernel.
Red Hat nash version 4.2.15 starting
mkrootdev: label / not found
mount: error 2 mounting ext3
ERROR opening /dev/console!!!!: 2
error dup2'ing fd of 0 to 0
error dup2'ing fd of 0 to 1
error dup2'ing fd of 0 to 2
switchroot: mount failed: 22
Kernel panic - not syncing: Attempted to kill init!
is this some sort of udev problem? I've googled this to death and I
cant find any resolution. tried giving different parameters to the
boot line to no effect.
explicitly setting root=/dev/sda1 did not work. it's an SATA
drive...what gets me is that 2.6.13 worked fine, but any 2.6.14 is
borked. so that indicates to me that the label on the disk is fine.
the boot parameters for my 2.6.13 are identical.
perhaps support for my SATA controller was removed? it seems
doubtful. SiL 3114 SATA Raid PCI card. The difference between the 13
and 14 boot seems to be at the line right after "Red Hat nash version
4.2.15 starting". the 13 gets to INIT, and the 14 bombs on mkrootdev.
It also seems less likely that ext3 support was taken out of
2.6.14 :)...I'm a little nervous about removing udev as it seems
2.6.13 uses it and I'd like to have a somewhat working system.
thanks for any help and sorry if I've left any important information
out.
Can you post your complete machine configuration.
Motherboard, memory, etc.
mobo: Asus A7V880 KT880
RAM: 1 GB single-channel PC3200 DDR400 (2x512 dimms)
/proc/cpuinfo :
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(tm)
stepping : 1
cpu MHz : 1250.252
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 2506.12
here is dmesg from the 2.6.13 boot. I hope this is enough to cover
the "etc" part. thanks much.
-----------
Linux version 2.6.13-1.1532_FC4 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxx)
(gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 Thu Oct 20 01:30:08
EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff40000 (usable)
BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data)
BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 261952
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32576 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f9190
ACPI: RSDT (v001 A M I OEMRSDT 0x09000502 MSFT 0x00000097) @
0x3ff40000
ACPI: FADT (v002 A M I OEMFACP 0x09000502 MSFT 0x00000097) @
0x3ff40200
ACPI: MADT (v001 A M I OEMAPIC 0x09000502 MSFT 0x00000097) @
0x3ff40300
ACPI: OEMB (v001 A M I OEMBIOS 0x09000502 MSFT 0x00000097) @
0x3ff50040
ACPI: DSDT (v001 A0008 A0008705 0x00000705 INTL 0x02002026) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 40000000 (gap: 40000000:bf7c0000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c04e7000 soft=c04e6000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1250.252 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032216k/1047808k available (3085k kernel code, 14628k
reserved, 704k data, 176k init, 130304k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay using timer specific routine.. 2506.12 BogoMIPS
(lpj=5012258)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000
00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000020
00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c28)
checking if image is initramfs... it is
Freeing initrd memory: 1219k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post
a report
pnp: 00:0a: ioport range 0x480-0x487 has been reserved
pnp: 00:0a: ioport range 0xc00-0xc7f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fb700000-fd8fffff
PREFETCH window: 97f00000-a7efffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1136970897.452:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key EEDDDBBBC3364C64
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1])
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT880 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKB] -> GSI 3 (level,
low) -> IRQ 3
ttyS4: detected caps 00000700 should be 00000100
ttyS4 at I/O 0xedc0 (irq = 3) is a 16C950/954
ttyS5: detected caps 00000700 should be 00000100
ttyS5 at I/O 0xedc8 (irq = 3) is a 16C950/954
ttyS6: detected caps 00000700 should be 00000100
ttyS6 at I/O 0xedd0 (irq = 3) is a 16C950/954
ttyS7: detected caps 00000700 should be 00000100
ttyS7 at I/O 0xedd8 (irq = 3) is a 16C950/954
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKB] -> GSI 3 (level,
low) -> IRQ 3
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 3
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1835008 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PS2K PS2M UAR1 USB1 USB2 USB3 USB4 EHCI VUSB PCI1 PCI2 PCI3 PCI4
PCI5 SLPB
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
SCSI subsystem initialized
libata version 1.12 loaded.
sata_sil version 0.9
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
ata1: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma
0xF8804000 irq 10
ata2: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma
0xF8804008 irq 10
ata3: SATA max UDMA/100 cmd 0xF8804280 ctl 0xF880428A bmdma
0xF8804200 irq 10
ata4: SATA max UDMA/100 cmd 0xF88042C0 ctl 0xF88042CA bmdma
0xF8804208 irq 10
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01
87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01
87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01
87:4003 88:207f
ata3: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
ata3: dev 0 configured for UDMA/100
scsi2 : sata_sil
ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01
87:4003 88:207f
ata4: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
ata4: dev 0 configured for UDMA/100
scsi3 : sata_sil
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdc: drive cache: write back
sdc: sdc1
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 320173056 512-byte hdwr sectors (163929 MB)
SCSI device sdd: drive cache: write back
sdd:
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
sata_via version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
sata_via(0000:00:0f.0): routed to hard irq line 10
ata5: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEF8E bmdma 0xEE90 irq 10
ata6: SATA max UDMA/133 cmd 0xEEF0 ctl 0xEF8A bmdma 0xEE98 irq 10
ata5: no device found (phy stat 00000000)
scsi4 : sata_via
ata6: no device found (phy stat 00000000)
scsi5 : sata_via
md: raid1 personality registered as nr 3
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdc1 ...
md: adding sdc1 ...
md: created md0
md: bind<sdc1>
md: running: <sdc1>
raid1: raid set md0 active with 1 out of 2 mirrors
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
snd: no version for "struct_module" found: kernel tainted.
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
ALSA /var/tmp/bach-build/BUILD/alsa-driver-1.0.10rc3/pci/../alsa-
kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0x107e5368]
ALSA /var/tmp/bach-build/BUILD/alsa-driver-1.0.10rc3/pci/../alsa-
kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0x107e5368]
ALSA /var/tmp/bach-build/BUILD/alsa-driver-1.0.10rc3/pci/../alsa-
kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0x107e5368]
ALSA /var/tmp/bach-build/BUILD/alsa-driver-1.0.10rc3/pci/../alsa-
kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0x107e5368]
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.13-1.1532_FC4 686 REGPARM 4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
tveeprom: ivtv version
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8401771
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tda9885/6/7: chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: Encoder revision: 0x02040024
ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011
or 0x02050032.
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
(2048KB total)
ivtv0: Create encoder radio stream
tuner 0-0061: type set to 47 (LG NTSC (TAPE series))
ivtv0: Initialized WinTV PVR 150, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 5 (level,
low) -> IRQ 5
tveeprom: The eeprom says no radio is present, but the tuner type 68
tveeprom: indicates otherwise. I will assume that radio is present.
tveeprom: ivtv version
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8200629
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
: chip found @ 0xc2 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tda9885/6/7: chip found @ 0x86
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1: Encoder revision: 0x02040024
ivtv1 warning: Encoder Firmware can be buggy, use version 0x02040011
or 0x02050032.
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
(2048KB total)
ivtv1: Create encoder radio stream
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv1: Initialized WinTV PVR 150, card #1
ivtv: ====================== NEXT CARD ======================
ivtv2: Autodetected WinTV PVR 250 card (iTVC16 based)
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
tveeprom: ivtv version
tveeprom: Hauppauge: model = 32062, rev = B185, serial# = 7478102
tveeprom: tuner = TCL 2002N 6A (idx = 85, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP3445 (type = c)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50]
: chip found @ 0xc2 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61]
saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=saa7115, addr=21]
msp34xx: ivtv version
msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Oct 21 2005 02:12:13
ivtv2: i2c attach to card #2 ok [client=MSP3445G-B8, addr=40]
ivtv2: loading /lib/modules/ivtv-fw-enc.bin
ivtv2: Encoder revision: 0x02040024
ivtv2 warning: Encoder Firmware can be buggy, use version 0x02040011
or 0x02050032.
ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
total)
ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
total)
ivtv2: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
total)
ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
(2048KB total)
tuner 2-0061: type set to 50 (TCL 2002N)
ivtv2: Initialized WinTV PVR 250, card #2
ivtv: ==================== END INIT IVTV ====================
lirc_dev: IR Remote Control driver registered, at major 61
bttv: disagrees about version of symbol tveeprom_hauppauge_analog
bttv: Unknown symbol tveeprom_hauppauge_analog
cx88xx: disagrees about version of symbol tveeprom_hauppauge_analog
cx88xx: Unknown symbol tveeprom_hauppauge_analog
cx8800: Unknown symbol cx88_reset
cx8800: Unknown symbol cx88_call_i2c_clients
cx8800: Unknown symbol cx88_wakeup
cx8800: Unknown symbol cx88_risc_stopper
cx8800: Unknown symbol cx88_print_irqbits
cx8800: Unknown symbol cx88_set_scale
cx8800: Unknown symbol cx88_shutdown
cx8800: Unknown symbol cx88_vdev_init
cx8800: Unknown symbol cx88_core_put
cx8800: Unknown symbol cx88_audio_thread
cx8800: Unknown symbol cx88_core_irq
cx8800: Unknown symbol cx88_core_get
cx8800: Unknown symbol cx88_get_stereo
cx8800: Unknown symbol cx88_set_tvnorm
cx8800: Unknown symbol cx88_risc_buffer
cx8800: Unknown symbol cx88_set_stereo
cx8800: Unknown symbol cx88_sram_channels
cx8800: Unknown symbol cx88_set_tvaudio
cx8800: Unknown symbol cx88_sram_channel_dump
cx8800: Unknown symbol cx88_sram_channel_setup
cx8800: Unknown symbol cx88_print_ioctl
cx8800: Unknown symbol cx88_free_buffer
cx8800: Unknown symbol cx88_boards
cx8800: Unknown symbol cx88_newstation
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
ivtv2: i2c attach to card #2 ok [client=Hauppauge IR, addr=18]
lirc_dev: lirc_register_plugin: sample_rate: 10
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000eea0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000eec0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 3 (level,
low) -> IRQ 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 3, io base 0x0000ef00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 3 (level,
low) -> IRQ 3
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 3, io base 0x0000ef20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
NET: Registered protocol family 10
Disabled Privacy Extensions on device c04756a0(lo)
IPv6 over IPv4 tunneling driver
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7667 Fri
Jun 17 07:01:04 PDT 2005
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
cdrom: open failed.
cdrom: open failed.
EXT3 FS on sda1, internal journal
ReiserFS: md0: found reiserfs format "3.6" with standard journal
ReiserFS: md0: using ordered data mode
ReiserFS: md0: journal params: device md0, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: md0: checking transaction log (md0)
ReiserFS: md0: Using r5 hash to sort names
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
ReiserFS: sdb1: using ordered data mode
ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
ReiserFS: sdb1: checking transaction log (sdb1)
ReiserFS: sdb1: Using r5 hash to sort names
Adding 1052248k swap on /dev/sda3. Priority:-1 extents:1
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
eth0: no IPv6 routers present
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
