I have notebook with default installation of Fedora 4 and braodband via
USB Thomson Speedtouch 330 modem. I did everything as I was told by
this site www.linux-usb.org/SpeedTouch/fedora/. I downloaded firmware, put this line into /etc/ppp/chap-secrets
'username@isp' * 'password'
and created file /etc/sysconfig/network-scripts/ifcfg-ppp0
PEERDNS=yes
TYPE=xDSL
DEVICE=ppp0
BOOTPROTO=dialup
PIDFILE=/var/run/pppoa-adsl.pid
LCP_FAILURE=86400
LCP_INTERVAL=1
CONNECT_POLL=6
CONNECT_TIMEOUT=604800
SYNCHRONOUS=no
DEFROUTE=yes
USER='username@isp'
VPI=0
VCI=38
LINUX_PLUGIN=pppoatm.so
DEMAND=yes
I JUST REBOOTED AND EVERYTHING WORKED JUST FINE!
But
now I have two more computers at home and they need internet as well. I
bought cheap P2 350 for router, installed the same FC4 from the same
CDs. Did all the same steps as I did with my notebook. But I have not
the same results.
On boot time during ppp0 initialization I get message
does not seem to be present, delaying initialization. [FAILED]
And there is all relevant output in /var/log/messages I have
Oct 12 16:43:33 octopus kernel: hub 1-0:1.0: USB hub found
Oct 12 16:43:33 octopus kernel: hub 1-0:1.0: 2 ports detected
Oct 12 16:43:33 octopus kernel: usb 1-1: new full speed USB device using uhci_hcd and address 2
Oct 12 16:43:34 octopus kernel: usb 1-1: reset full speed USB device using uhci_hcd and address 2
Oct 12 16:43:34 octopus kernel: usbcore: registered new driver speedtch
Oct 12 16:43:34 octopus kernel: speedtch 1-1:1.0: found stage 1 firmware speedtch-1.bin
Oct 12 16:43:34 octopus kernel: speedtch 1-1:1.0: found stage 2 firmware speedtch-2.bin
Oct 12 16:43:34 octopus kernel: ATM dev 0: ADSL line is synchronising
Oct 12 16:43:35 octopus kernel: ATM dev 0: ADSL line is up (2272 kb/s down | 288 kb/s up)
While on my notebook, which works just fine, I get much more output on /var/log/messages:
Oct 12 10:49:09 pasaka pppd[2006]: Plugin pppoatm.so loaded.
Oct 12 10:49:09 pasaka pppd[2006]: PPPoATM plugin_init
Oct 12 10:49:09 pasaka pppd[2006]: PPPoATM setdevname_pppoatm - SUCCESS:0.38
Oct 12 10:49:09 pasaka pppd[2006]: pppd 2.4.2 started by root, uid 0
Oct 12 10:49:09 pasaka pppd[2006]: Using interface ppp0
Oct 12 10:49:09 pasaka pppd[2006]: local IP address 10.112.112.112
Oct 12 10:49:09 pasaka pppd[2006]: remote IP address 10.112.112.113
Oct 12 10:49:10 pasaka pppd[2006]: Starting link
Oct 12 10:49:10 pasaka pppd[2006]: Connect: ppp0 <--> 0.38
Oct 12 10:49:10 pasaka pppd[2006]: Couldn't increase MTU to 1500. Using 1492
Oct 12 10:49:10 pasaka pppd[2006]: Couldn't increase MRU to 1500. Using 1492
Oct 12 10:49:10 pasaka kernel: usbcore: registered new driver usbfs
Oct 12 10:49:10 pasaka kernel: usbcore: registered new driver hub
Oct 12 10:49:13 pasaka pppd[2006]: Couldn't increase MTU to 1500. Using 1492
Oct 12 10:49:13 pasaka pppd[2006]: Couldn't increase MTU to 1500. Using 1492
Oct 12 10:49:14 pasaka pppd[2006]: Couldn't increase MRU to 1500. Using 1492
Oct 12 10:49:14 pasaka pppd[2006]: Couldn't increase MTU to 1600. Using 1492
Oct 12 10:49:14 pasaka pppd[2006]: Couldn't increase MRU to 1500. Using 1492
Oct 12 10:49:14 pasaka pppd[2006]: CHAP authentication succeeded
Oct 12 10:49:14 pasaka kernel: usbcore: registered new driver hiddev
Oct 12 10:49:14 pasaka pppd[2006]: Local IP address changed to 84.43.100.94
Oct 12 10:49:14 pasaka kernel: usbcore: registered new driver usbhid
Oct 12 10:49:15 pasaka pppd[2006]: Remote IP address changed to 212.67.121.45
Oct 12 10:49:18 pasaka kernel: hub 4-0:1.0: USB hub found
Oct 12 10:49:18 pasaka kernel: hub 4-0:1.0: 2 ports detected
Oct 12 10:49:18 pasaka kernel: usb 2-1: new low speed USB device using uhci_hcd and address 2
Oct 12 10:49:18 pasaka kernel: usb 2-2: reset full speed USB device using uhci_hcd and address 3
Oct 12 10:49:18 pasaka kernel: usbcore: registered new driver speedtch
Oct 12 10:49:18 pasaka kernel: speedtch 2-2:1.0: found stage 1 firmware speedtch-1.bin
Oct 12 10:49:18 pasaka kernel: speedtch 2-2:1.0: found stage 2 firmware speedtch-2.bin
Oct 12 10:49:18 pasaka kernel: ATM dev 0: ADSL line is synchronising
Oct 12 10:49:20 pasaka kernel: ATM dev 0: ADSL line is up (2272 kb/s down | 288 kb/s up)
Can anyone give me a clue what is wrong with my FC4 router?
--
Dovydas Sankauskas
