Re: Is the HP PSC 1315 not recognized by FC4?

[Vinicius <cviniciusm@xxxxxxxxxxxx>]

Vinicius escreveu:
> Vinicius escreveu:
>
> > Jerry DeLisle escreveu:
> >
> > > Vinicius wrote:
> > >
> > > > Jerry DeLisle escreveu:
> > > >
> > > > > Vinicius wrote:
> > > > >
> > > > > > Hello,
> > > > > >
> > > > > > I have a HP PSC 1315 and the computer OS is FC4 (the kernel is 
> > > > > > 2.6.12-1.1387_FC4).
> > > > > >
> > > > > > The command lspci is not showing the printer, but it did show on 
> > > > > > FC3 and the printer was working on FC3.
> > > > > >
> > > > > > Any ideias, please?
> > > > > >
> > > > > >
> > > > > > TIA,
> > > > > >
> > > > > > Vinicius.
> > > > > Go to this site.
> > > > >
> > > > > http://hpinkjet.sourceforge.net/
> > > > >
> > > > > There are details for installation.  I have hplip running on FC4 
> > > > > like a charm.  Puts an icon in the accessories menu.  Click on that 
> > > > > and you have full control.
> > > > >
> > > > > Jerry
> > > >
> > > > Thanks.
> > > >
> > > > Is your SELinux active ("enforcing" and "targeted")?
> > > >
> > > > I have used hplip since 0.8X to 0.9.2 without problem on FC3.
> > > > I have compiled and installed it (version 0.9.3) on FC4, but there 
> > > > are several "avc denied" due to SELinux.
> > > > Unfortunately, I think it's a hardware or configuration issue. I 
> > > > don't know if it is due kudzu or the kernel, or other component.
> > > > As I said, the command *lspci* is not showing the printer, 
> > > > independent of hplip installation or not.
> > > >
> > > >
> > > > Vinicius.
> > > I do have SELinux enabled and have a few "avc denied" messages but 
> > > all is working.  I have a PSC 2175 plugged into USB port.  It shows 
> > > up fine with lsusb. I do not know the kind of interface for PSC 
> > > 1315.  I would try the hplip mailing list and see if they have any 
> > > ideas.
> > >
> > > Jerry
> >
> > Thanks again.
> >
> > I'm participating of the HPLIP forums but without success to solve the 
> > problem there.
> >
> > I have reinstalled the FC4 from the zero and the problem continues.
> >
> > Have you installed the FC4 from the zero or upgraded from another 
> > version of Fedora, please?
> >
> > My PSC 1315 uses USB to communicate with the computer.
> >
> > What's the outputs of the commands lsusb and lspci, please?
> >
> >
> > TIA,
> >
> > Vinicius.
>
> Before the tip:
> "
> # lsusb
> Bus 005 Device 001: ID 0000:0000
> Bus 004 Device 001: ID 0000:0000
> Bus 003 Device 001: ID 0000:0000
> Bus 002 Device 001: ID 0000:0000
> Bus 001 Device 001: ID 0000:0000
> "
>
> After the tip from Kam Leo:
> "
> Bus 005 Device 001: ID 0000:0000
> *Bus 004 Device 002: ID 03f0:3f11 Hewlett-Packard PSC-1315*
> Bus 004 Device 001: ID 0000:0000
> Bus 003 Device 001: ID 0000:0000
> Bus 002 Device 001: ID 0000:0000
> Bus 001 Device 001: ID 0000:0000
> "
>
> Now I can install the HPLIP driver.
>
>
> Thanks,
>
> Vinicius.

Hello,

there is something strange, because each restart of the computer, lsusb 
is not showing the printer, I can see the printer information after I 
turn off and then turn on the printer.

Vinicius.