On Tue, 8 Feb 2005 11:53:18 -0500 (EST), Steven W. Orr <steveo@xxxxxxxxxxx> wrote: > On Monday, Feb 7th 2005 at 16:07 -0600, quoth akonstam@xxxxxxxxxxx: > > =>On Mon, Feb 07, 2005 at 03:04:26PM -0500, Steven W. Orr wrote: > =>> On Monday, Feb 7th 2005 at 11:31 -0800, quoth Rick Stevens: > =>> > =>> =>Steven W. Orr wrote: > =>> =>> I have had the same problem with Core1 and Core2. Now it's happening again > =>> =>> with Core3. > =>> =>> > =>> =>> I have the following config: > =>> =>> > =>> =>> Tyan K7 Thunder Dual processors Athlon MB with 3 SCSI drives and one IDE > =>> =>> drive used for backup. > =>> =>> > =>> =>> Here's df: > =>> =>> > =>> =>> 513 > df -v > =>> =>> Filesystem Size Used Avail Use% Mounted on > =>> =>> /dev/sda3 22G 14G 7.4G 65% / > =>> =>> /dev/sda1 99M 17M 78M 18% /boot > =>> =>> /dev/hda1 3.7G 324M 3.2G 10% /f > =>> =>> /dev/hda2 70G 60G 6.6G 91% /g > =>> =>> /dev/sdc1 8.4G 6.6G 1.5G 83% /home > =>> =>> /dev/sdb1 8.4G 6.2G 1.8G 79% /home2 > =>> =>> /dev/sdc2 26G 6.0G 19G 25% /h > =>> =>> none 504M 0 504M 0% /dev/shm > =>> =>> /dev/sda6 9.9G 6.4G 3.1G 68% /usr > =>> =>> /dev/sda5 1011M 462M 499M 49% /var > =>> =>> 514 > > =>> =>> > =>> =>> > =>> =>> When I reboot with Install Disk 1, I get the splash screen giving me the > =>> =>> choice of the (normal graphic or text) (install or upgrage). I choose > =>> =>> either. I get a few lines saying tha vmlinuz is loading and then the whole > =>> =>> process just stops dead. I am vershtumped. > =>> =>> > =>> =>> Can someone please advise what to do or what additional info I need to > =>> =>> provide? > =>> => > =>> =>Uh, try adding "noapic" to the boot command. Dual Athlons sometimes > =>> =>need that. > =>> > =>> Good shot but no dice. It hangs exactly the same way. > =>> > =>> I am now officially open to a new suggestion. :-) > =>> > =>You don't say but in the install process it seems you don't get the > =>message that the SCSI driver is being installed. If that is not > =>happening I would guess the the fedora installer cannot recognize your > =>SCSI controller. Which controller do you have? > =>------------------------------------------- > =>Aaron Konstam > =>Computer Science > =>Trinity University > =>One Trinity Place. > =>San Antonio, TX 78212-7200 > => > =>telephone: (210)-999-7484 > =>email:akonstam@xxxxxxxxxxx > => > > Aaron, this sounds promising. I have a Tyan K7 Thunder motherboard which > has a pair of Adaptec 7899W controllers. The bootable disc is hooked up to > one of the two contollers. In addition, there's an IDE drive that's hooked > up to the builtin IDE controller. The BIOS is config'd to boot off of > SCSI. Do I need to do anything to tell the CDROM to boot off of SCSI? > > -- > Time flies like the wind. Fruit flies like a banana. Stranger things have .0. > happened but none stranger than this. Does your driver's license say Organ ..0 > Donor?Black holes are where God divided by zero. Listen to me! We are all- 000 > individuals! What if this weren't a hypothetical question? > steveo at syslang.net > If an IDE drive is installed the code in my Adaptec SCSI controllers would not load its BIOS. So the solution for you may be to install GRUB in the MBR of the IDE drive.
