Keith Lofstrom schrieb:
Thanks a lot. Just tried to format a 20 GB disk with mke2fs -j /dev/sda1 - it also hanged the device. So I will format the hdd in a normal way (but probably not today, it would require some DIY again), but here is:It will help to learn the chipset in your enclosure, which may appear in /proc/bus/usb/devices . You might also open the case and read the chipset markings off the big LSI on the USB2 interface board.
I BCCed my friend, so perhaps he can weigh in here. Please help the young fellow achieve fame and fortune (or at least resume points) by providing observations that will help him debug this pesky problem.
Keith
[root@localhost root]# cat /proc/bus/usb/devices
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.8-1.521 ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:03.1 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.8-1.521 ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:03.0 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.8-1.521 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:03.3 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05e3 ProdID=0702 Rev= 0.02 S: Product=USB TO IDE C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 96mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Here the numbers from the board:
1. The interface board reads: 2PCB03U-OI30478 IDE---XXX304718 C26
2. The chip reads: Q811USB 0351WHGA6-24
(I am not sure about the H in the second line - it is written in very small letters)
Maybe it is of interest, that my BIOS does not recognize the big 250 GB Maxtor which is now in the normal internal IDE slot. The BIOS says "none", but FC2 mounts it and I can use it without any problem. So I attach:
[root@localhost root]# dmesg | grep BIOS BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) PCI: PCI BIOS revision 2.10 entry at 0xfbbd0, last bus=1 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:pio
Thank you and greetings Markus
