Getting a USB driver added for a device ? (Hitec HPP-22, wine, USB, RC)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I use the Hitec Aurora 9 (A9) transmitter for my remote control
vehicles.

http://www.hitecrcd.com/products/aircraft-radios-receivers-and-accesories/aircraft/aurora9/aurora-9-2-4ghz.html

This transmitter is part of a system of devices.   One of the devices in
this system is the HPP-22, which is a USB device that allows a computer
to communicate with the A9 in order to load and save model information
as well as update the firmware in the transmitter and receivers.

http://www.hitecrcd.com/products/aircraft-radios-receivers-and-accesories/telemetry/hpp-22.html

Hitec publishes closed source Windows based software to enable a Windows
computer to communicate with the HPP-22.

http://hitecrcd.co.kr/tester/hpp_22.htm

After renaming the install file from "Install_hpp_22_V1.04(1).exe" to
"Install_hpp_22_V1.04.exe" in Dolphin, wine runs the installer just
fine, albeit with a few warning messages.   

Note: Bash doesn't allow () characters.  Doing a right click on the file
name in Dolphin allowed me to change it.   In hindsight this could have
been corrected when downloading the install fall. 

When I run the resulting HPP-22 program, it displays "HPP-22 is
disconnected."  Ie its not finding the HPP-22 hardware connected to the
PC via a USB cable.

dmesg states the following:
======================================================
[263071.342137] usb 6-1: new full speed USB device using uhci_hcd and
address 4
[263071.514255] usb 6-1: New USB device found, idVendor=1e1a,
idProduct=001f
[263071.514266] usb 6-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[263071.514273] usb 6-1: Product: HPP-22
[263071.514278] usb 6-1: Manufacturer: HITECRCD Inc
[263071.514283] usb 6-1: SerialNumber:   HPP-22-00000
[263071.524680] generic-usb 0003:1E1A:001F.0005: hiddev97,hidraw2: USB
HID v0.01 Device [HITECRCD Inc HPP-22] on usb-0000:00:1d.1-1/input0
=======================================================

lsusb returns this:
======================================================
$ lsusb
Bus 007 Device 002: ID 046d:c521 Logitech, Inc. Cordless Mouse Receiver
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 004: ID 1e1a:001f  
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth +
WLAN) Interface [Integrated Module]
Bus 003 Device 002: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint
Sensor
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 064e:a101 Suyin Corp. Acer CrystalEye Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 07ca:a321 AVerMedia Technologies, Inc. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
=======================================================

At this point I have been advised that the proper USB driver has not
been installed for the HPP-22 device.   Who should I talk to to get this
done or get help to do it myself ?

Thanks !

LG123

Other information

I'm running a fully up to date Fedora 14 system.

$ yum list wine
Installed Packages
wine.i686
1.3.14-2.fc14
@updates

$ uname -a
Linux localhost.localdomain 2.6.35.11-83.fc14.i686.PAE #1 SMP Mon Feb 7
06:57:55 UTC 2011 i686 i686 i386 GNU/Linux

$ yum list udev
Installed Packages
udev.i686
161-8.fc14
@anaconda-InstallationRepo-201010211814.i38

usbview returns the following (and indicates that a driver is attached
to the HPP22 device)

HPP-22
Manufacturer: HITECRCD Inc
Serial Number:   HPP-22-00000
Speed: 12Mb/s (full)
USB Version:  2.00
Device Class: 00(>ifc )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 8
Number of Configurations: 1
Vendor Id: 1e1a
Product Id: 001f
Revision Number:  0.01

Config Number: 1
        Number of Interfaces: 1
        Attributes: 80
        MaxPower Needed: 100mA

        Interface Number: 0
                Name: usbhid
                Alternate Number: 0
                Class: 03(HID  ) 
                Sub Class: 00
                Protocol: 00
                Number of Endpoints: 2

                        Endpoint Address: 81
                        Direction: in
                        Attribute: 3
                        Type: Int.
                        Max Packet Size: 64
                        Interval: 10ms

                        Endpoint Address: 01
                        Direction: out
                        Attribute: 3
                        Type: Int.
                        Max Packet Size: 64
                        Interval: 10ms

usbmon does not indicate any activity whatsoever on the bus the HPP-22
is connected to.  My guess is that the HPP-22 software is not finding
the HPP-22 hardware and is thus not attempting to talk to it.




-- 
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines


[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux