On 27/04/2010 2:00 AM, Michael Miles wrote:
On 04/26/2010 07:27 AM, suvayu ali wrote:
On 26 April 2010 06:46, badmagic<badmagic@xxxxxxxxxxxx> wrote:
Hi all (figured out the problem),
I've had trouble installing Fedora for the last few releases. I don't
have it installed at the moment so I can't offer much help BUT as I'm
certain my prob relates to my EVGA GTX 295 Co-Op Edition graphics card
and these are quite common cards, I'm sure the fix is quite widely known.
Everything installs/boots okay until I get to the bit where I need to
log in. I get the GDM graphical login screen but the mouse and keyboard
seem to stop working. If I change to terminal view (Ctrl Alt F2 for
memory) I can still type DMESG shows problems with the graphics card -
can't remember specifics.
I tried changing the xorg.conf to settings I know worked under other
distros/BSD/Solaris (using xorg) to no avail.
Is this a known problem? Is there a fix? Is there some GRUB switch I can
throw in there that'll work - I tried some to no avail.
I am not sure but your card is probably not supported by the open
source nouveau drivers. Have you tried using the proprietary drivers
packaged by rpmfusion [http://rpmfusion.org/Howto/nVidia]? If not you
could give that a shot. I would go about it like this,
1. Boot to runlevel 3
2. use yum to install rpmfusion free and non-free repo
3. now use yum to install the nvidia proprietary drivers
4. reboot
My specs are as follows:
ASUS P5Q Deluxe motherboard
4GB Kingston (compatible with mobo) RAM
EVGA GTX 295 co-op edition graphics card
Corsair HX 1000W (more than enough)
Nice rig ;)
That's about all
GL
Regards,
Steve Laurie
You must also blacklist nouveau in the grub config
There is a complete write up in the above RPMFUSION HOWTO
Hi all,
Still no success on the graphics. I get the graphical screen come up
with the word
Fedora and 1 dot under the F (are the number of dots some kind of
indication of
progress? Not sure but I thoough it might be a clue).
at this point, the mouse still works and the keyboard still has power
but it's as though the
keyboard doesn't work. Not even the caps lock, number lock etc. lights
change
when I press the associated buttons. Needless to say Ctrl-Alt-F2 doesn't
work.
I am still trying to do what has already been suggested but in the mean
time, if someone
could take a look at my dmesg (attached), I'd appreciate it.
Also, while I was in runlevel 3, I created an xorg.conf.new file and
have also attached that.
Perhaps it can give some clues as to what's going on.
Thanks,
Steve Laurie
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.31.5-127.fc12.x86_64 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.2 20091027 (Red Hat 4.4.2-7) (GCC) ) #1 SMP Sat Nov 7 21:11:14 EST 2009
Command line: initrd=initrd0.img root=live:CDLABEL=Fedora-12-x86_64-Live-KDE rootfstype=auto ro liveimg quiet rhgb rd_NO_LUKS rd_NO_MD noiswmd init 3 BOOT_IMAGE=vmlinuz0
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bff70000 (usable)
BIOS-e820: 00000000bff70000 - 00000000bff7e000 (ACPI data)
BIOS-e820: 00000000bff7e000 - 00000000bffd0000 (ACPI NVS)
BIOS-e820: 00000000bffd0000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x140000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-DFFFF write-protect
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F00000000 write-back
1 base 100000000 mask FC0000000 write-back
2 base 0C0000000 mask FC0000000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 4GB, type WB
reg 1, base: 4GB, range: 1GB, type WB
reg 2, base: 3GB, range: 1GB, type UC
total RAM coverred: 4096M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 64K num_reg: 3 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 4GB, range: 1GB, type WB
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000c0000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbff70 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bff70000
0000000000 - 00bfe00000 page 2M
00bfe00000 - 00bff70000 page 4k
kernel direct mapping tables up to bff70000 @ 10000-15000
init_memory_mapping: 0000000100000000-0000000140000000
0100000000 - 0140000000 page 2M
kernel direct mapping tables up to 140000000 @ 13000-19000
RAMDISK: 7f533000 - 7fffe09e
ACPI: RSDP 00000000000faff0 00024 (v02 ACPIAM)
ACPI: XSDT 00000000bff70100 0005C (v01 A_M_I_ OEMXSDT 07000910 MSFT 00000097)
ACPI: FACP 00000000bff70290 000F4 (v03 A_M_I_ OEMFACP 07000910 MSFT 00000097)
ACPI: DSDT 00000000bff70440 09721 (v01 A0999 A0999001 00000001 INTL 20060113)
ACPI: FACS 00000000bff7e000 00040
ACPI: APIC 00000000bff70390 0006C (v01 A_M_I_ OEMAPIC 07000910 MSFT 00000097)
ACPI: MCFG 00000000bff70400 0003C (v01 A_M_I_ OEMMCFG 07000910 MSFT 00000097)
ACPI: OEMB 00000000bff7e040 00089 (v01 A_M_I_ AMI_OEM 07000910 MSFT 00000097)
ACPI: HPET 00000000bff79b70 00038 (v01 A_M_I_ OEMHPET 07000910 MSFT 00000097)
ACPI: OSFR 00000000bff79bb0 000B0 (v01 A_M_I_ OEMOSFR 07000910 MSFT 00000097)
ACPI: SSDT 00000000bff7ead0 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20060113)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-0000000140000000
Bootmem setup node 0 0000000000000000-0000000140000000
NODE_DATA [0000000000014000 - 0000000000029fff]
bootmap [000000000002a000 - 0000000000051fff] pages 28
(8 early reservations) ==> bootmem [0000000000 - 0140000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 00019adb00] TEXT DATA BSS ==> [0001000000 - 00019adb00]
#3 [007f533000 - 007fffe09e] RAMDISK ==> [007f533000 - 007fffe09e]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [00019ae000 - 00019ae290] BRK ==> [00019ae000 - 00019ae290]
#6 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000]
#7 [0000013000 - 0000014000] PGTABLE ==> [0000013000 - 0000014000]
found SMP MP-table at [ffff8800000ff780] ff780
[ffffea0000000000-ffffea00045fffff] PMD -> [ffff880028600000-ffff88002bdfffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00140000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000bff70
0: 0x00100000 -> 0x00140000
On node 0 totalpages: 1048319
DMA zone: 56 pages used for memmap
DMA zone: 103 pages reserved
DMA zone: 3824 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 767912 pages, LIFO batch:31
Normal zone: 3584 pages used for memmap
Normal zone: 258560 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a301 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
PM: Registered nosave memory: 00000000bff70000 - 00000000bff7e000
PM: Registered nosave memory: 00000000bff7e000 - 00000000bffd0000
PM: Registered nosave memory: 00000000bffd0000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:3ee00000)
NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 29 pages at ffff880028022000, static data 90080 bytes
Built 1 zonelists in Node order, mobility grouping on. Total pages: 1030296
Policy zone: Normal
Kernel command line: initrd=initrd0.img root=live:CDLABEL=Fedora-12-x86_64-Live-KDE rootfstype=auto ro liveimg quiet rhgb rd_NO_LUKS rd_NO_MD noiswmd init 3 BOOT_IMAGE=vmlinuz0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Initializing CPU#0
xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 4048240k/5242880k available (4227k kernel code, 1049604k absent, 145036k reserved, 2926k data, 1324k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:440
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 2999.631 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 41943040 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
HPET: 4 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 5999.26 BogoMIPS (lpj=2999631)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU 0/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Counters: Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic counters: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose counters: 3
... counter mask: 0000000700000003
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20852 entries in 82 pages
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Quad CPU Q9650 @ 3.00GHz stepping 0a
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5999.08 BogoMIPS (lpj=2999540)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU 1/0x1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Quad CPU Q9650 @ 3.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Booting processor 2 APIC 0x2 ip 0x6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 8278.73 BogoMIPS (lpj=4139366)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU 2/0x2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
mce: CPU supports 6 MCE banks
CPU2: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
CPU2: Intel(R) Core(TM)2 Quad CPU Q9650 @ 3.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Booting processor 3 APIC 0x3 ip 0x6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 5999.09 BogoMIPS (lpj=2999545)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU 3/0x3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
mce: CPU supports 6 MCE banks
CPU3: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: Intel(R) Core(TM)2 Quad CPU Q9650 @ 3.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
Total of 4 processors activated (26276.16 BogoMIPS).
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=584 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=776 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=248 bytes
sizeof(task_struct)=6008 bytes
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
domain 1: span 0-3 level CPU
groups: 0-1 2-3
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
domain 1: span 0-3 level CPU
groups: 0-1 2-3
CPU2 attaching sched-domain:
domain 0: span 2-3 level MC
groups: 2 3
domain 1: span 0-3 level CPU
groups: 2-3 0-1
CPU3 attaching sched-domain:
domain 0: span 2-3 level MC
groups: 3 2
domain 1: span 0-3 level CPU
groups: 2-3 0-1
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 22:04:50 Date: 04/30/10
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0xb800-0xb81f]
pci 0000:00:1a.1: reg 20 io port: [0xb880-0xb89f]
pci 0000:00:1a.2: reg 20 io port: [0xbc00-0xbc1f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xf5fffc00-0xf5ffffff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf5ff8000-0xf5ffbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xb080-0xb09f]
pci 0000:00:1d.1: reg 20 io port: [0xb400-0xb41f]
pci 0000:00:1d.2: reg 20 io port: [0xb480-0xb49f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf5fff800-0xf5fffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 001f)
pci 0000:00:1f.2: reg 10 io port: [0xa000-0xa007]
pci 0000:00:1f.2: reg 14 io port: [0x9c00-0x9c03]
pci 0000:00:1f.2: reg 18 io port: [0x9880-0x9887]
pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803]
pci 0000:00:1f.2: reg 20 io port: [0x9480-0x948f]
pci 0000:00:1f.2: reg 24 io port: [0x9400-0x940f]
pci 0000:00:1f.3: reg 10 64bit mmio: [0xf5fff400-0xf5fff4ff]
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:00:1f.5: reg 10 io port: [0xb000-0xb007]
pci 0000:00:1f.5: reg 14 io port: [0xac00-0xac03]
pci 0000:00:1f.5: reg 18 io port: [0xa880-0xa887]
pci 0000:00:1f.5: reg 1c io port: [0xa800-0xa803]
pci 0000:00:1f.5: reg 20 io port: [0xa480-0xa48f]
pci 0000:00:1f.5: reg 24 io port: [0xa400-0xa40f]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:01.0: bridge io port: [0xc000-0xdfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf6000000-0xfeafffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xdfffffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:01:00.0: bridge io port: [0xc000-0xdfff]
pci 0000:01:00.0: bridge 32bit mmio: [0xf6000000-0xfeafffff]
pci 0000:01:00.0: bridge 64bit mmio pref: [0xc0000000-0xdfffffff]
pci 0000:03:00.0: reg 10 32bit mmio: [0xf9000000-0xf9ffffff]
pci 0000:03:00.0: reg 14 64bit mmio: [0xc0000000-0xcfffffff]
pci 0000:03:00.0: reg 1c 64bit mmio: [0xf6000000-0xf7ffffff]
pci 0000:03:00.0: reg 24 io port: [0xcc00-0xcc7f]
pci 0000:03:00.0: reg 30 32bit mmio: [0xf8f80000-0xf8ffffff]
pci 0000:02:00.0: bridge io port: [0xc000-0xcfff]
pci 0000:02:00.0: bridge 32bit mmio: [0xf6000000-0xf9ffffff]
pci 0000:02:00.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:04:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:04:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
pci 0000:04:00.0: reg 24 io port: [0xdc00-0xdc7f]
pci 0000:04:00.0: reg 30 32bit mmio: [0xfea80000-0xfeafffff]
pci 0000:02:02.0: bridge io port: [0xd000-0xdfff]
pci 0000:02:02.0: bridge 32bit mmio: [0xfa000000-0xfeafffff]
pci 0000:02:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xfebe0000-0xfebfffff]
pci 0000:05:00.0: reg 14 32bit mmio: [0xfebc0000-0xfebdffff]
pci 0000:05:00.0: reg 18 io port: [0xec00-0xec3f]
pci 0000:05:00.0: reg 30 32bit mmio: [0xfeba0000-0xfebbffff]
pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
vgaarb: device added: PCI:0000:04:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: old code would have set cacheline size to 32 bytes, but clflush_size = 64
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:06: ioport range 0x290-0x29f has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x500-0x57f could not be reserved
system 00:07: iomem range 0xfed08000-0xfed08fff has been reserved
system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:07: iomem range 0xfed50000-0xfed8ffff has been reserved
system 00:0a: iomem range 0xffc00000-0xffdfffff has been reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0xbfffffff could not be reserved
system 00:0d: iomem range 0xe0000000-0xffffffff could not be reserved
pci 0000:05:00.0: BAR 6: address space collision on of device [0xfeba0000-0xfebbffff]
pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
pci 0000:02:00.0: IO window: 0xc000-0xcfff
pci 0000:02:00.0: MEM window: 0xf6000000-0xf9ffffff
pci 0000:02:00.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:02:02.0: PCI bridge, secondary bus 0000:04
pci 0000:02:02.0: IO window: 0xd000-0xdfff
pci 0000:02:02.0: MEM window: 0xfa000000-0xfeafffff
pci 0000:02:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: 0xc000-0xdfff
pci 0000:01:00.0: MEM window: 0xf6000000-0xfeafffff
pci 0000:01:00.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xc000-0xdfff
pci 0000:00:01.0: MEM window: 0xf6000000-0xfeafffff
pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0: IO window: 0xe000-0xefff
pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:1e.0: PREFETCH window: 0xf0000000-0xf00fffff
alloc irq_desc for 16 on node 0
alloc kstat_irqs on node 0
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:00.0: setting latency timer to 64
pci 0000:02:02.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0xc000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xf6000000-0xfeafffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xdfffffff]
pci_bus 0000:02: resource 0 io: [0xc000-0xdfff]
pci_bus 0000:02: resource 1 mem: [0xf6000000-0xfeafffff]
pci_bus 0000:02: resource 2 pref mem [0xc0000000-0xdfffffff]
pci_bus 0000:03: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:03: resource 1 mem: [0xf6000000-0xf9ffffff]
pci_bus 0000:03: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:04: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:04: resource 1 mem: [0xfa000000-0xfeafffff]
pci_bus 0000:04: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:05: resource 0 io: [0xe000-0xefff]
pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff]
pci_bus 0000:05: resource 2 pref mem [0xf0000000-0xf00fffff]
pci_bus 0000:05: resource 3 io: [0x00-0xffff]
pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 0
Freeing initrd memory: 11052k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1272665089.515:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7928
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:04:00.0: Boot video device
alloc irq_desc for 24 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
ACPI: SSDT 00000000bff7e0d0 00277 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
processor LNXCPU:00: registered as cooling_device0
ACPI: SSDT 00000000bff7e350 00277 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
processor LNXCPU:01: registered as cooling_device1
ACPI: SSDT 00000000bff7e5d0 00277 (v01 DpgPmm P003Ist 00000012 INTL 20060113)
processor LNXCPU:02: registered as cooling_device2
ACPI: SSDT 00000000bff7e850 00277 (v01 DpgPmm P004Ist 00000012 INTL 20060113)
processor LNXCPU:03: registered as cooling_device3
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
ata_piix 0000:00:1f.2: version 2.13
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19
ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf5fffc00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
alloc irq_desc for 23 on node 0
alloc kstat_irqs on node 0
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf5fff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
alloc irq_desc for 21 on node 0
alloc kstat_irqs on node 0
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000bc00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.31.5-127.fc12.x86_64 uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
PM: Resume from disk failed.
registered taskstats version 1
No TPM chip found, activating TPM-bypass!
Magic number: 6:91:99
rtc_cmos 00:03: setting system clock to 2010-04-30 22:04:50 UTC (1272665090)
Initalizing network drop monitor service
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
usb 2-4: new high speed USB device using ehci_hcd and address 2
usb 2-4: New USB device found, idVendor=1b80, idProduct=e400
usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: DVB-T 2
usb 2-4: Manufacturer: Afatech
usb 2-4: configuration #1 chosen from 1 choice
ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-8: ST3500418AS, CC38, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.01: ATAPI: HL-DT-ST DVDRAM GH22NS50, TN01, max UDMA/100
ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/133
ata1.00: ATA-8: ST3500418AS, CC38, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.01: ATAPI: ATAPI iHAS324 Y, BL1Y, max UDMA/100
ata2.01: configured for UDMA/100
ata1.00: configured for UDMA/133
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3500418AS CC38 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
scsi 0:0:1:0: CD-ROM ATAPI iHAS324 Y BL1Y PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sda:
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg1 type 5
scsi 1:0:0:0: Direct-Access ATA ST3500418AS CC38 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 1:0:1:0: CD-ROM HL-DT-ST DVDRAM GH22NS50 TN01 PQ: 0 ANSI: 5
sda1 sda2 sda3 sda4 <sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
sdb:
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg3 type 5
sda5 sdb1
sdb1: <bsd: sdb5 sdb6 sdb7 sdb8 sdb9 >
sd 1:0:0:0: [sdb] Attached SCSI disk
sda6 >
usb 8-1: new full speed USB device using uhci_hcd and address 2
sda3: <bsd: sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 1324k freed
Write protecting the kernel read-only data: 6344k
dracut: dracut-002-13.4.git8f397a9b.fc12
dracut: rd_NO_LUKS: removing cryptoluks activation
dracut: root was live:/dev/disk/by-label/Fedora-12-x86_64-Live-KDE, liveroot is now live:CDLABEL=Fedora-12-x86_64-Live-KDE
udev: starting version 145
[drm] Initialized drm 1.1.0 20060810
nouveau 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nouveau 0000:03:00.0: setting latency timer to 64
[drm] nouveau 0000:03:00.0: Detected an NV50 generation card (0x0a0580b1)
[drm] nouveau 0000:03:00.0: Attempting to load BIOS image from PRAMIN
[drm] nouveau 0000:03:00.0: ... BIOS signature not found
[drm] nouveau 0000:03:00.0: Attempting to load BIOS image from PROM
usb 8-1: New USB device found, idVendor=046d, idProduct=c318
usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 8-1: Product: Logitech Illuminated Keyboard
usb 8-1: Manufacturer: Logitech
usb 8-1: configuration #1 chosen from 1 choice
input: Logitech Logitech Illuminated Keyboard as /devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.0/input/input3
generic-usb 0003:046D:C318.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech Logitech Illuminated Keyboard] on usb-0000:00:1d.2-1/input0
input: Logitech Logitech Illuminated Keyboard as /devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.1/input/input4
generic-usb 0003:046D:C318.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Logitech Logitech Illuminated Keyboard] on usb-0000:00:1d.2-1/input1
[drm] nouveau 0000:03:00.0: ... appears to be valid
[drm] nouveau 0000:03:00.0: BIT BIOS found
[drm] nouveau 0000:03:00.0: Bios version 62.00.6c.00
[drm] nouveau 0000:03:00.0: TMDS table revision 2.0 not currently supported
[drm] nouveau 0000:03:00.0: Found Display Configuration Block version 4.0
nouveau 0000:03:00.0: PCI INT A disabled
nouveau 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
nouveau 0000:04:00.0: setting latency timer to 64
[drm] nouveau 0000:04:00.0: Detected an NV50 generation card (0x0a0580b1)
[drm] nouveau 0000:04:00.0: Attempting to load BIOS image from PRAMIN
usb 8-2: new low speed USB device using uhci_hcd and address 3
[drm] nouveau 0000:04:00.0: ... appears to be valid
[drm] nouveau 0000:04:00.0: BIT BIOS found
[drm] nouveau 0000:04:00.0: Bios version 62.00.6c.00
[drm] nouveau 0000:04:00.0: TMDS table revision 2.0 not currently supported
[drm] nouveau 0000:04:00.0: Found Display Configuration Block version 4.0
[drm] nouveau 0000:04:00.0: Raw DCB entry 0: 04000320 00000028
[drm] nouveau 0000:04:00.0: Raw DCB entry 1: 01000322 00020030
[drm] nouveau 0000:04:00.0: Raw DCB entry 2: 02011310 00000028
[drm] nouveau 0000:04:00.0: Raw DCB entry 3: 02011312 00020030
[drm] nouveau 0000:04:00.0: Raw DCB entry 4: 0000000e 00000000
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table 0 at offset 0xD2ED
[drm] nouveau 0000:04:00.0: INIT_87 stubbed!
[drm] nouveau 0000:04:00.0: 0xEC67: Init table command not found: 0x35
[drm] nouveau 0000:04:00.0: INIT_87 stubbed!
[drm] nouveau 0000:04:00.0: 0xEC8A: Init table command not found: 0xDD
[drm] nouveau 0000:04:00.0: INIT_87 stubbed!
[drm] nouveau 0000:04:00.0: 0xEC44: Init table command not found: 0x93
[drm] nouveau 0000:04:00.0: INIT_87 stubbed!
[drm] nouveau 0000:04:00.0: 0xECAD: Init table command not found: 0x00
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table 1 at offset 0xD72A
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table 2 at offset 0xEBC7
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table 3 at offset 0xECA4
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table 4 at offset 0xED76
[drm] nouveau 0000:04:00.0: Parsing VBIOS init table at offset 0xEDDB
[drm] nouveau 0000:04:00.0: 0xEDDB: Condition still not met after 20ms, skipping following opcodes
[drm] nouveau 0000:04:00.0: 0xC248: parsing output script 0
[drm] nouveau 0000:04:00.0: 0xC248: parsing output script 0
usb 8-2: New USB device found, idVendor=045e, idProduct=0039
usb 8-2: New USB device strings: Mfr=1, Product=3, SerialNumber=0
usb 8-2: Product: Microsoft 5-Button Mouse with IntelliEye(TM)
usb 8-2: Manufacturer: Microsoft
usb 8-2: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input5
generic-usb 0003:045E:0039.0003: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.2-2/input0
[TTM] Zone kernel: Available graphics memory: 2030310 kiB.
[drm] nouveau 0000:04:00.0: 896 MiB VRAM
[drm] nouveau 0000:04:00.0: 512 MiB GART (aperture)
[drm] nouveau 0000:04:00.0: Allocating FIFO number 1
[drm] nouveau 0000:04:00.0: nouveau_channel_alloc: initialised FIFO 1
[drm] nouveau 0000:04:00.0: Detected a DAC output
[drm] nouveau 0000:04:00.0: Detected a TMDS output
[drm] nouveau 0000:04:00.0: Detected a DAC output
[drm] nouveau 0000:04:00.0: Detected a TMDS output
[drm] nouveau 0000:04:00.0: Detected a DVI-I connector
[drm] nouveau 0000:04:00.0: Detected a DVI-I connector
[drm] nouveau 0000:04:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff880136415400
[drm] TMDS-8: set mode 1920x1200 2a
[drm] nouveau 0000:04:00.0: 0xC24C: parsing output script 1
[drm] nouveau 0000:04:00.0: 0xC24D: parsing output script 2
[drm] nouveau 0000:04:00.0: 0xC13D: parsing clock script 0
Console: switching to colour frame buffer device 240x75
[drm] nouveau 0000:04:00.0: 0xBA73: parsing clock script 1
fb0: nouveaufb frame buffer device
registered panic notifier
[drm] Initialized nouveau 0.0.15 20090420 for 0000:04:00.0 on minor 0
dracut: Starting plymouth daemon
dracut: rd_NO_MD: removing MD RAID activation
dracut: rd_NO_MDIMSM: no MD RAID for imsm/isw raids
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
squashfs: version 4.0 (2009/01/31) Phillip Lougher
EXT4-fs (dm-0): barriers enabled
kjournald2 starting: pid 405, dev dm-0:8, commit interval 5 seconds
EXT4-fs (dm-0): internal journal on dm-0:8
EXT4-fs (dm-0): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (dm-0): mounted filesystem with ordered data mode
dracut: Mounted root filesystem /dev/mapper/live-rw
dracut: Loading SELinux policy
type=1404 audit(1272665100.685:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux: 8 users, 12 roles, 2941 types, 136 bools, 1 sens, 1024 cats
SELinux: 75 classes, 144734 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext4), uses xattr
SELinux: initialized (dev loop2, type squashfs), not configured for labeling
SELinux: initialized (dev loop0, type squashfs), not configured for labeling
SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1272665101.442:3): policy loaded auid=4294967295 ses=4294967295
dracut: Switching root
udev: starting version 145
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ACPI: I/O resource 0000:00:1f.3 [0x400-0x41f] conflicts with ACPI region SMRG [0x400-0x40f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000: 0000:05:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:1b:21:56:3d:75
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
alloc irq_desc for 22 on node 0
alloc kstat_irqs on node 0
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
device-mapper: multipath: version 1.1.0 loaded
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib64/xorg/modules"
FontPath "catalogue:/etc/X11/fontpath.d"
FontPath "built-ins"
EndSection
Section "Module"
Load "dbe"
Load "dri2"
Load "dri"
Load "extmod"
Load "glx"
Load "record"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "VideoKey" # <i>
#Option "FPDither" # [<bool>]
#Option "FPScale" # [<bool>]
#Option "ScalingMode" # <str>
#Option "EXAPixmaps" # [<bool>]
Identifier "Card0"
Driver "nouveau"
VendorName "nVidia Corporation"
BoardName "Unknown Board"
BusID "PCI:4:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
--
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
