Hi, I've configured multipath but I'm confused with the following. When I run "multipath -v2" I don't get any output, but if I run "multipath -v3" I get lot's of output e.g.: cciss!c0d0: not found in pathvec cciss!c0d0: mask = 0x1f dm-0: blacklisted hda: blacklisted loop0: blacklisted loop1: blacklisted loop2: blacklisted loop3: blacklisted loop4: blacklisted loop5: blacklisted loop6: blacklisted loop7: blacklisted md0: blacklisted ram0: blacklisted ram10: blacklisted ram11: blacklisted ram12: blacklisted ram13: blacklisted ram14: blacklisted ram15: blacklisted ram1: blacklisted ram2: blacklisted ram3: blacklisted ram4: blacklisted ram5: blacklisted ram6: blacklisted ram7: blacklisted ram8: blacklisted ram9: blacklisted sda: not found in pathvec sda: mask = 0x1f sda: bus = 1 sda: dev_t = 8:0 sda: size = 19534921728 sda: vendor = HP sda: product = MSA2012sa sda: rev = J300 sda: h:b:t:l = 0:0:0:1 sda: serial = 00c0ffd7ba4f00004575b24a01000000 sda: path checker = tur (controller setting) sda: state = 2 sda: getprio = /sbin/mpath_prio_alua %d (controller setting) sda: prio = 50 sda: getuid = /sbin/hp_scsi_id -g -u -n -s /block/%n (controller setting) sda: uid = 3600c0ff000d7ba4f4575b24a01000000 (callout) sdb: not found in pathvec sdb: mask = 0x1f sdb: bus = 1 sdb: dev_t = 8:16 sdb: size = 19534921728 sdb: vendor = HP sdb: product = MSA2012sa sdb: rev = J300 sdb: h:b:t:l = 1:0:0:2 sdb: serial = 00c0ffd7ba4f00004575b24a01000000 sdb: path checker = tur (controller setting) sdb: state = 2 sdb: getprio = /sbin/mpath_prio_alua %d (controller setting) sdb: prio = 10 sdb: getuid = /sbin/hp_scsi_id -g -u -n -s /block/%n (controller setting) sdb: uid = 3600c0ff000d7ba4f4575b24a01000000 (callout) ===== paths list ===== uuid hcil dev dev_t pri dm_st chk_st vend/pr 3600c0ff000d7ba4f4575b24a01000000 0:0:0:1 sda 8:0 50 [undef][ready] HP,MSA2 3600c0ff000d7ba4f4575b24a01000000 1:0:0:2 sdb 8:16 10 [undef][ready] HP,MSA2 params = 1 queue_if_no_path 0 2 1 round-robin 0 1 1 8:0 100 round-robin 0 1 1 8:16 100 status = 2 0 0 0 2 1 A 0 1 0 8:0 A 0 E 0 1 0 8:16 A 0 Found matching wwid [3600c0ff000d7ba4f4575b24a01000000] in bindings file. Setting alias to mpath0 sda: ownership set to mpath0 sda: not found in pathvec sda: mask = 0xc sda: state = 2 sda: prio = 50 sdb: ownership set to mpath0 sdb: not found in pathvec sdb: mask = 0xc sdb: state = 2 sdb: prio = 10 mpath0: pgfailback = -2 (controller setting) mpath0: pgpolicy = group_by_prio (controller setting) mpath0: selector = round-robin 0 (controller setting) mpath0: features = 0 (internal default) mpath0: hwhandler = 0 (controller setting) mpath0: rr_weight = 1 (internal default) mpath0: minio = 100 (controller setting) mpath0: no_path_retry = 18 (controller setting) pg_timeout = NONE (internal default) mpath0: set ACT_NOTHING (map unchanged) multipath -ll mpath0 (3600c0ff000d7ba4f4575b24a01000000) dm-0 HP,MSA2012sa [size=9.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=50][active] \_ 0:0:0:1 sda 8:0 [active][ready] \_ round-robin 0 [prio=10][enabled] \_ 1:0:0:2 sdb 8:16 [active][ready] Does that mean multipath is working on /dev/sda and /dev/sdb? Is the lack of output for "multipath -v2" a concern? Thanks Dan -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
