On Dec 11, 2007 1:41 PM, Les <hlhowell@xxxxxxxxxxx> wrote:
>
> On Tue, 2007-12-11 at 13:29 +1100, Lux Zhang wrote:
> > Hi
> > there is an error message on my laptop HPnx5000 as
> > "hald-addon-acpi[2845]: segfault at 00000ffc eip 00aaf3ec esp bf956ba8
> > error 4"
> > My system is F7 Linux 2.6.23.8-34.fc7 #1 SMP
> >
> > What does this error mean or any potential harm?
> >
> > Yuan
> >
> Segfaults are not good. Typically it means the program attempted to
> access memory it did not have permission to access, or in other words,
> it crashed into something else in memory. In this case it was an addon
> to hald which is the haldaemon, and the specific add on is the acpi
> module, which is part of the power control stuff. If you have a laptop,
> it might be that the particular power setup and bios is not compatible
> with the format being sought by linux. If the sensor is sufficiently
> sensitive, it may be generating repeated interrupt service calls and
> eventually the interrupt code will furthur interrupt the system,
> overflowing the segment allocated to the operating stack.
>
> You will have to check out the sensors and by isolating one bit of code
> at a time and seeing if it is fixed.
Thanks for your information. I updated the BIOS from HP web site.
However, the error is still here.
attached below is dmesg message. Could you guide a few steps to solve this?
Best
Yuandan
Linux version 2.6.23.8-34.fc7
(kojibuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2
20070925 (Red Hat 4.1.2-27)) #1 SMP Thu Nov 22 23:05:33 EST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004f7d0000 (usable)
BIOS-e820: 000000004f7d0000 - 000000004f7f0c00 (reserved)
BIOS-e820: 000000004f7f0c00 - 000000004f7fc000 (ACPI NVS)
BIOS-e820: 000000004f7fc000 - 000000004f800000 (reserved)
375MB HIGHMEM available.
896MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 325584) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 325584
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 325584
On node 0 totalpages: 325584
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 751 pages used for memmap
HighMem zone: 95457 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F6C00, 0014 (r0 COMPAQ)
ACPI: RSDT 4F7F0C84, 0030 (r1 COMPAQ CPQ0058 30080620 CPQ 1)
ACPI: FACP 4F7F0C00, 0084 (r2 COMPAQ CPQ0058 2 CPQ 1)
ACPI: DSDT 4F7F0D10, 623A (r1 HP nx5000 10000 MSFT 100000E)
ACPI: FACS 4F7FBE80, 0040
ACPI: APIC 4F7F0CB4, 005A (r1 COMPAQ CPQ0058 1 CPQ 1)
ACPI: SSDT 4F7F6F4A, 028A (r1 COMPAQ CPQGysr 1001 MSFT 100000E)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfec01000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 4f800000:b0800000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 323041
Kernel command line: ro root=LABEL=/1 rhgb quiet
mapped APIC to ffffb000 (fec01000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07a5000 soft=c0785000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1594.834 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1282836k/1302336k available (2175k kernel code, 18268k
reserved, 1113k data, 280k init, 384832k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc073c000 - 0xc0782000 ( 280 kB)
.data : 0xc061fe65 - 0xc0736544 (1113 kB)
.text : 0xc0400000 - 0xc061fe65 (2175 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3190.77 BogoMIPS (lpj=1595388)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000
00000180 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f3bf 00000000 00000000 00002040
00000180 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Total of 1 processors activated (3190.77 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=1552 bytes
Booting paravirtualized kernel on bare hardware
Time: 21:56:23 Date: 12/16/07
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [C045] (0000:00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C045.C057._PRT]
ACPI: PCI Interrupt Link [C0C2] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0C3] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0C4] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0C5] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0C6] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0C7] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0C8] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *10 11)
ACPI: Power Resource [C171] (on)
ACPI: Power Resource [C141] (on)
ACPI: Power Resource [C188] (on)
ACPI: Power Resource [C18F] (on)
ACPI: Power Resource [C199] (on)
ACPI: Power Resource [C0E6] (on)
ACPI: Power Resource [C1FE] (off)
ACPI: Power Resource [C1FF] (off)
ACPI: Power Resource [C200] (off)
ACPI: Power Resource [C201] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x4f7fffff could not be reserved
pnp: 00:0c: iomem range 0xffb00000-0xffbfffff has been reserved
pnp: 00:0c: iomem range 0xfff00000-0xffffffff has been reserved
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f has been reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
pnp: 00:0d: iomem range 0xfec00000-0xfec000ff has been reserved
pnp: 00:0d: iomem range 0xfec10000-0xfec1ffff has been reserved
pnp: 00:0e: iomem range 0xfec01000-0xfec01fff has been reserved
PCI: Bus 2, cardbus bridge: 0000:01:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 50000000-53ffffff
MEM window: 5c000000-5fffffff
PCI: Bus 3, cardbus bridge: 0000:01:06.1
IO window: 00003800-000038ff
IO window: 00003c00-00003cff
PREFETCH window: 54000000-57ffffff
MEM window: 60000000-63ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: 90000000-903fffff
PREFETCH window: 50000000-57ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 18 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:01:06.1[A] -> GSI 18 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2817k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1197842183.552:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 31E176BC2F9DAC60
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Transitioning device [C202] to D3
ACPI: Transitioning device [C202] to D3
ACPI: Fan [C202] (off)
ACPI: Transitioning device [C203] to D3
ACPI: Transitioning device [C203] to D3
ACPI: Fan [C203] (off)
ACPI: Transitioning device [C204] to D3
ACPI: Transitioning device [C204] to D3
ACPI: Fan [C204] (off)
ACPI: Transitioning device [C205] to D3
ACPI: Transitioning device [C205] to D3
ACPI: Fan [C205] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (61 C)
ACPI: Thermal Zone [TZ2] (24 C)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Switched to high resolution mode on CPU 0
ACPI: Thermal Zone [TZ3] (23 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
agpgart: Detected an Intel 855GM Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0x98000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Clocksource tsc unstable (delta = -293914037 ns)
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Yenta: CardBus bridge found at 0000:01:06.0 [103c:08bc]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:06.0, mfunc 0x012c1202, devctl 0x64
Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff
Yenta: CardBus bridge found at 0000:01:06.1 [103c:08bc]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:06.1, mfunc 0x012c1202, devctl 0x64
Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#01) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff
PNP: PS/2 Controller [PNP0303:C196,PNP0f13:C197] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 3:359:955
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 844k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 18, io base 0x000028c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x000028e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00002c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0x90500000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input2
SCSI subsystem initialized
libata version 2.21 loaded.
ata_piix 0000:00:1f.1: version 2.12
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00012c20 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00012c28 irq 15
ata1.00: ATA-6: TOSHIBA MK4026GAX, PA103G, max UDMA/100
ata1.00: 78140160 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
usb 1-2: device not accepting address 2, error -71
ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4243N, 1.07, max MWDMA2
usb 4-2: new high speed USB device using ehci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
hub 4-2:1.0: USB hub found
hub 4-2:1.0: 4 ports detected
ata2.00: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4026GA PA10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4243N 1.07 PQ: 0 ANSI: 5
usb 4-2.2: new low speed USB device using ehci_hcd and address 3
usb 4-2.2: configuration #1 chosen from 1 choice
input: USB Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.7-2.2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1197842190.235:2): selinux=0 auid=4294967295
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
cs: IO port probe 0x100-0x3af: excluding 0x100-0x107 0x140-0x14f 0x378-0x37f
cs: IO port probe 0x100-0x3af: excluding 0x100-0x107 0x140-0x14f 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
parport_pc 00:05: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
NET: Registered protocol family 23
input: PC Speaker as /class/input/input4
intel_rng: FWH not detected
ieee80211_crypt: registered algorithm 'NULL'
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [C13D]
input: Lid Switch as /class/input/input7
ACPI: Lid Switch [C13C]
Detected unconfigured HP nx5000 family SMSC IrDA chip, pre-configuring device.
Setting up Intel 82801 controller and SMSC device
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x004e): LPC47N227
smsc_superio_flat(): fir: 0x130, sir: 0x2f8, dma: 03, irq: 5, mode: 0x0e
SMsC IrDA Controller found
IrCC version 2.0, firport 0x130, sirport 0x2f8 dma=3, irq=5
No transceiver found. Defaulting to Fast pin select
IrDA: Registered device irda0
ACPI: Battery Slot [C13B] (battery present)
ACPI: Battery Slot [C13A] (battery absent)
ACPI: AC Adapter [C139] (on-line)
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
input: Video Bus as /class/input/input8
ACPI: Video Device [C046] (multi-head: yes rom: no post: no)
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 21 (level, low) -> IRQ 21
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
ACPI: PCI Interrupt 0000:01:0d.0[A] -> GSI 23 (level, low) -> IRQ 20
firewire_ohci: Added fw-ohci device 0000:01:0d.0, OHCI version 1.10
ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 20 (level, low) -> IRQ 22
ssb: Sonics Silicon Backplane found on PCI device 0000:01:0e.0
b44.c:v2.0
ACPI: PCI Interrupt 0000:01:06.3[A] -> GSI 18 (level, low) -> IRQ 16
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0d:9d:8f:12:79
net eth0_rename: device_rename: sysfs_create_symlink failed (-17)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
net eth0: device_rename: sysfs_create_symlink failed (-17)
net eth1: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0_rename to eth1
AC'97 0 analog subsections not ready
firewire_core: created new fw device fw0 (0 config rom retries, S400)
intel8x0_measure_ac97_clock: measured 50488 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.6 to 64
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 18
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda8, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1239800k swap on /dev/sda6. Priority:-1 extents:1 across:1239800k
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
audit(1197842224.493:3): audit_pid=1992 old=0 by auid=4294967295
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon[2082]: VMCI: Driver initialized.
/dev/vmmon[2082]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[2082]: Module vmmon: initialized
/dev/vmnet: open called by PID 2105 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 2120 (vmnet-netifup)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2121 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 2118 (vmnet-natd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2156 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 2157 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
eth0: no IPv6 routers present
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ttyS0: LSR safety check engaged!
ttyS2: LSR safety check engaged!
ppdev: user-space parallel port driver
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
ttyS0: LSR safety check engaged!
ttyS2: LSR safety check engaged!
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm] Initialized i915 1.6.0 20060119 on minor 1
hald-addon-acpi[2715]: segfault at 00000ffc eip 00aaf3ec esp bfb12d68 error 4
>
> Regards,
> Les H
>
> --
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
>
