I just rebooted one of my SAN hosts, running FC6, and had it boot into the latest FC6 kernel 2.6.22-9. After the boot, the primary SAN partitions it mounts weren't available. A check through /var/log/messages revealed this little nugget: Nov 9 10:01:04 blowingrock kernel: QLogic Fibre Channel HBA Driver Nov 9 10:01:04 blowingrock kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection Nov 9 10:01:04 blowingrock kernel: ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 28 (level, low) -> IRQ 28 Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Found an ISP2300, irq 28, iobase 0xffffc20001438000 Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Configuring PCI space... Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Configure NVRAM parameters... Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Verifying loaded RISC code... Nov 9 10:01:04 blowingrock kernel: ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 26 (level, low) -> IRQ 26 Nov 9 10:01:04 blowingrock kernel: e1000: 0000:02:04.1: e1000_probe: (PCI:33MHz:64-bit) 00:04:23:a8:96:d7 Nov 9 10:01:04 blowingrock kernel: Floppy drive(s): fd0 is 1.44M Nov 9 10:01:04 blowingrock kernel: FDC 0 is a post-1991 82077 Nov 9 10:01:04 blowingrock kernel: e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Firmware image unavailable. Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Firmware images can be retrieved from: ftp://ftp.qlogic.com/outgoing/linux/firmware/. Nov 9 10:01:04 blowingrock kernel: qla2xxx 0000:01:01.0: Failed to initialize adapter So, in my panic, I reset grub to point back to the existing .20 kernel and all came up just fine: Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: Found an ISP2300, irq 28, iobase 0xffffc20000022000 Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: Configuring PCI space... Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: Configure NVRAM parameters... Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: Verifying loaded RISC code... Nov 9 10:31:06 blowingrock kernel: Intel(R) PRO/1000 Network Driver - version 7.3.15-k2-NAPI Nov 9 10:31:06 blowingrock kernel: Copyright (c) 1999-2006 Intel Corporation. Nov 9 10:31:06 blowingrock kernel: input: PC Speaker as /class/input/input3 Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: Allocated (412 KB) for firmware dump... Nov 9 10:31:06 blowingrock kernel: scsi2 : qla2xxx Nov 9 10:31:06 blowingrock kernel: hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33) Nov 9 10:31:06 blowingrock kernel: Uniform CD-ROM driver Revision: 3.20 Nov 9 10:31:06 blowingrock kernel: Floppy drive(s): fd0 is 1.44M Nov 9 10:31:06 blowingrock kernel: FDC 0 is a post-1991 82077 Nov 9 10:31:06 blowingrock kernel: qla2xxx 0000:01:01.0: LOOP UP detected (2 Gbps). So my question, WTH is going on here? I've obviously missed a memo or something. -- Recedite, plebes! Gero rem imperialem! Mark Haney Sr. Systems Administrator ERC Broadband (828) 350-2415 Call (866) ERC-7110 for after hours support
