Re: System -> Administration -> Soundcard detection no longer hear sound

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Darlene Wallach wrote:
stan wrote:
Darlene Wallach wrote:
stan wrote:
Darlene Wallach wrote:
While I was installing Fedora 7, I heard sound during
the sound test. After Fedora 7 was installed, I tried
System -> Administration -> Soundcard detection and I
heard sound.

I installed Macromedia, mplayer, vlc. I tried to watch
youtube and did not hear sound. I used the
System -> Preferences -> Personal -> volume control

I now do not hear sound when I select
System -> Administration -> Soundcard detection.

What could explain the soundcard not being detected?

Should I reinstall Fedora 7?

I sent an email out on Monday, 20th Aug to which noone
has responded. Are people tired of helping people get
sound working? Is the subject of no interest?

If anyone can give advice or feedback, I would appreciate
it. Can someone point me to documentation?

Thank you for your attention and consideration,

Darlene Wallach

See if your sound card has been detected.
aplay some.wav    this will use the default device
aplay -D plughw:0,0 some.wav  uses a different plugin than default

You can also look at aplay -lLv to see the info alsa has about your card and how it has configured it.
There is lots of information in /proc/asound as well.

By default alsa starts with sound muted, so use either the alsa mixer gui
or alsamixer in a terminal to adjust at least the master sound level.

If you have more than one soundcard, it is possible that they were assigned in a different order than you expect. This requires explicit assignment it /etc/modprobe.conf. Lately, I've noticed this occurring by default.

Some applications need to be configured to use the card.

And yes, this question has been asked and answered many times on the list. The answer has to be out there somewhere on the web, for sure on either the alsa-user list or this list at gmane.org.
I'm sure you find the subject of interest. :-)

I've had pretty good luck with sound, the basic functions have just worked. If you are using an obscure chip, or a troublesome chip it can be problematic. And because every sound card is different, only someone familiar with your card can really go beyond the basic stuff above. For those, the alsa lists are probably the best bet. They can also tell you if it is even supported.


I did check all the email on the Fedora list regarding
sound problems with Fedora 7. What I did not see was
someone asking about sound working on the sound test
during installation and after installation, then the
sound test failing.

I do not understand what to do change on alsamixer either
the cli or the gui to try to get sound working again.

I tried aplay on a .au file and heard nothing.

I don't know what to put in google to even get close to
getting results that will be useful.

I am very frustrated with myself for somehow screwing up
sound that once worked.

Darlene Wallach

If it once worked, it will work again.  That is a positive.
What kind of card is it?

Does aplay -lLv show any output, or does it say 'no sound device detected'?
default:CARD=Revolution51
   M Audio Revolution-5.1, ICE1724
   Default Audio Device
front:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   Front speakers
surround40:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   4.0 Surround output to Front and Rear speakers
surround41:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Revolution51,DEV=0
   M Audio Revolution-5.1, ICE1724
   IEC958 (S/PDIF) Digital Audio Output
null
   Discard all samples (playback) or generate zero samples (capture)
**** List of PLAYBACK Hardware Devices ****
card 0: Revolution51 [M Audio Revolution-5.1], device 0: ICE1724 [ICE1724]
 Subdevices: 0/1
 Subdevice #0: subdevice #0
card 0: Revolution51 [M Audio Revolution-5.1], device 1: IEC1724 IEC958 [IEC1724 IEC958]
 Subdevices: 1/1
 Subdevice #0: subdevice #0
card 0: Revolution51 [M Audio Revolution-5.1], device 2: ICE1724 Surrounds [ICE1724 Surround PCM]
 Subdevices: 2/2
 Subdevice #0: subdevice #0
 Subdevice #1: subdevice #1

Or, equivalently, when you look in /proc/asound do you see information? Does it exist? card0 cards devices modules oss pcm Revolution51 seq timers version

If you don't see either of the above, your sound card is not detected. Do the dmesg below to find out why.

If there is a card, do this.
Open a terminal.  Type alsamixer.
You will be on the master volume control. Push the up arrow until it is at a reasonable height, just below the red or just in the red. Press escape.

Now try your sound again.

Do a "dmesg | grep -i snd"
and a "dmesg | grep -i alsa"

If your sound is not installing, there will be messages indicating errors in the output.
Please post those errors.



# aplay -lLv
default:CARD=AudioPCI
    Ensoniq AudioPCI, ES1371 DAC2/ADC
    Default Audio Device
front:CARD=AudioPCI,DEV=0
    Ensoniq AudioPCI, ES1371 DAC2/ADC
    Front speakers
surround40:CARD=AudioPCI,DEV=0
    Ensoniq AudioPCI, ES1371 DAC2/ADC
    4.0 Surround output to Front and Rear speakers
iec958:CARD=AudioPCI,DEV=0
    Ensoniq AudioPCI, ES1371 DAC2/ADC
    IEC958 (S/PDIF) Digital Audio Output
null
    Discard all samples (playback) or generate zero samples (capture)
**** List of PLAYBACK Hardware Devices ****
card 0: AudioPCI [Ensoniq AudioPCI], device 0: ES1371/1 [ES1371 DAC2/ADC]
  Subdevices: 0/1
  Subdevice #0: subdevice #0
card 0: AudioPCI [Ensoniq AudioPCI], device 1: ES1371/2 [ES1371 DAC1]
  Subdevices: 1/1
  Subdevice #0: subdevice #0


# ls /proc/asound/
AudioPCI  card0  cards  devices  modules  oss  pcm  seq  timers  version

I used alsamixer and reduced the master and master m
so that only one red square showd

I used wget to download
http://linuxmafia.com/pub/linux/misc/english.au
$ aplay -t au english.au
Playing Sparc Audio 'english.au' : Mu-Law, Rate 8000 Hz, Mono

I did not hear anything

# dmesg | grep -i snd
returns nothing

# dmesg | grep -i alsa
returns nothing

btw, I posted most of this and alot more in my original
message dated Monday, 20th August:
subject: sound prob Ensoniq ES1371 on Fedora 7

I pasted most of the contents of scsconfig.log.
I deleted parts I thought had nothing to do with
sound.

Thank you very much for responding to my email!

Darlene Wallach

You are very close to having sound. Everything looks good, it is just a slight configuration issue.
Try aplay -Dhw:0,0 your_sound_file
I think you should try to find a wav file if you can, I'm not sure that alsa converts formats. If you don't have one, install audacity and convert a file you have to a wav.

Also check if you have oss installed. There are programs out there that still use OSS instead of alsa. Unless the alsa oss emulation packages are installed, that won't work.

do yum list all | grep -i oss to find them.

if you have a .asoundrc in your home directory, move it to a backup. Do the same with all the configuration files in /etc, /etc/asound.conf and /etc/asound.state (might be in /etc/alsa/asound.state). Log in and out to refresh the configuration to the default for the card.


You do have speakers plugged in, right.  :-)

What does xmms do, (audio player). If it complains, go into the options and select alsa as the device.



[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux