Craig White wrote:
On Tue, 2007-07-17 at 10:23 -0700, Srikanth Konjarla wrote:
Craig White wrote:
On Mon, 2007-07-16 at 15:13 -0500, Mikkel L. Ellertson wrote:
Craig White wrote:
I am struggling trying to make a Palm T|X work on Fedora 7
The problem *may* lie with the fact that in order to make this box work
(A Dell Optiplex 320), that I have to add 'pci=nomsi acpi=off' kernel
params on bootup.
udevinfo tells me all about the device.
I can see the device exists when I plug it in and check it via
ls -l /dev/ttyUSB* and
ls -l /dev/pilot
but even if I try (as root),
pilot-xfer -l -p /dev/ttyUSB1 or pilot-xfer -l -p /dev/pilot show
nothing at all
Is the problem my kernel parameters?
It probably isn't your kernel parameters. If it were, then
/dev/ttyUSB0 and /dev/USB1 most likely not be created. What happens
if you use /dev/ttyUSB0? Or, if you have more then 2 ttyUSB*
entries, try using /dev/ttyUSB2. I don't remember if the T|X uses
the first or second USB serial port that is created when you hit sync...
----
OK - didn't know the impact of the kernel params
# ls -l /dev/ttyUSB*
crw-rw---- 1 root uucp 188, 0 2007-07-17 09:52 /dev/ttyUSB0
crw-rw---- 1 root uucp 188, 1 2007-07-17 09:52 /dev/ttyUSB1
and from dmesg...
usb 4-2: new full speed USB device using ohci_hcd and address 6
usb 4-2: configuration #1 chosen from 1 choice
visor 4-2:1.0: Handspring Visor / Palm OS converter detected
usb 4-2: Handspring Visor / Palm OS converter now attached to ttyUSB0
usb 4-2: Handspring Visor / Palm OS converter now attached to ttyUSB1
but while the palm is using ttyUSB0/1 - I get nada...
# pilot-xfer -l -p /dev/ttyUSB1
Listening for incoming connection on /dev/ttyUSB1...
# pilot-xfer -l -p /dev/ttyUSB0
Listening for incoming connection on /dev/ttyUSB0...
#
but never anything else ;-(
As you can see the device files are owned and writable by only root.
There are couple of options that you can try,
1. change the permissions on device files as root.
# chmod 777 /dev/ttyUSB*
Try to sync your palm.
----
you might note the "#" cli prompt which is typical for user root.
Trying to sync the palm is rather pointless if you can't do a basic
listing of the files on the palm from the pilot-xfer (pilot-link
package) which is the base package that all of the GUI tools
(JPilot/KPilot/GPilot) all use.
----
2. Review the udev rules for ttyUSB* under /etc/udev/rules.d. It is very
likely that the default mode is set to "0660". You can refer to
50-udev.rules file. Here is a link from one of the old RH Magazines.
http://www.redhat.com/magazine/002dec04/features/udev/
----
I am all over the udev rules - I am a long time palm user but that is
more for 'users' and I am simply trying to communicate with the palm via
pilot-xfer which as stated above, is the basic toolset for accessing a
palm. The udev rules are tilted towards user space and again, I am
trying to work this through as root first.
I am quite certain that this would work with FC-6 but that isn't the
point...there is an issue with F7 and it would help if someone related
what they have done to get a Palm working on F7 - especially one of the
newer 'OS5' Palms
BTW, i use a Sony Clie UX-50 with Palm OS v5.2
