Re: core 6 issues

Hmmm. I've never used dmesg | grep acpi before. My! That's some output, and

it's way beyond my understanding. Normally I just use the dmesg command, and

can make some sort of sense from the output from that.

I'll throw that back to Aaron to interpret that, as he suggested it.

If you just run dmesg, and scroll down a bit you should see references to
acpi, along with some suggestions as there are problems with it. If you can
post the relevant acpi bits from that it might be helpfull.

Nigel.

Hello Nigel,
here's some lines from my term. window as you suggested:

ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information

ACPI: Core revision 20060707

ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices

ACPI: Processor [CPU1] (supports 8 throttling states)

ACPI: Getting cpuindex for acpiid 0x3

ACPI: Getting cpuindex for acpiid 0x4
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS

ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 17 (level, low) -> IRQ 16
and others similar to this line.

Thanks again!
JJ

_________________________________________________________________