On Mon, 2006-11-20 at 20:49 +0000, Paul Ward wrote: > sounds like a posibility, I will check this out in the morning. > I have looked at the disk and it looks set correctly as device 0 master. > I did unplug the cable as I had to move the cable as the drive was > plugged into the middle conector and I had to change that to reach the > new drive. > > I have also noticed that since plugging in my testing drive (currently > FC6) it seems fine. > You seem to imply that you moved a drive from the end connector to the middle one on your IDE ribbon, and that drive was jumpered as master. I have seen some errors generated by having the drives misjumpered on a cable select cable (almost all IDE cables of the ultra type are cable select - with 3 different colored connectors). Those cables are designed to have the master on the end connector (black) and the slave on the center connector (gray). Jumpering them otherwise can cause errors. I personally always just jumper the drive to CS and then the cable position decides what it is (master or slave). > Thanks for the sanity check ;) > > On 20/11/06, bruce <bedouglas@xxxxxxxxxxxxx> wrote: > > hi adam... > > > > not to imply that this might be your issue... but i had something similar > > with a drive i was dealing with a few weeks ago. turned out to be a simple > > problem in that i hadn't plugged in the data cable completely, and that i > > hadn't properly configured the master/slave jumpers completely. > > > > > > > > -----Original Message----- > > From: fedora-list-bounces@xxxxxxxxxx > > [mailto:fedora-list-bounces@xxxxxxxxxx]On Behalf Of Adam Hough > > Sent: Monday, November 20, 2006 10:52 AM > > To: For users of Fedora > > Subject: Re: Hard Drive Error Disk or Motherboard? > > > > > > Have your tried testing the power supply yet? > > > > On Mon, 2006-11-20 at 18:48 +0000, Paul Ward wrote: > > > Hi, > > > > > > I started having a problem this morning after I added an extra drive > > > to my ide1 channel as a slave. > > > After only 60 seconds the following messages started to appear on my > > > tty1 screen. > > > I immediatly removed the new disk and tried again with the same messages. > > > Next thing was removing and changeing the ide cable again this did not > > work. > > > > > > I have read the following from another post but am unsure if this > > > would work also the file hardware does not exist on my FC5. > > > > > > I would like to add the board was running windozes a few years back > > > and it started having disk problems. I then shelved it for 6 months > > > but Fedora seemed ok for the last year on it untill now. > > > > > > Does anyone have any suggestions. > > > > > > Nov 20 10:12:09 myth kernel: hda: dma_intr: status=0x51 { DriveReady > > > SeekComplete Error } > > > Nov 20 10:12:09 myth kernel: hda: dma_intr: error=0x10 { > > > SectorIdNotFound }, LBAsect=110169966, high=6, low=9506670, > > > sector=110169951 > > > Nov 20 10:12:09 myth kernel: ide: failed opcode was: unknown > > > Nov 20 10:12:16 myth kernel: hda: dma_intr: status=0x51 { DriveReady > > > SeekComplete Error } > > > Nov 20 10:12:16 myth kernel: hda: dma_intr: error=0x10 { > > > SectorIdNotFound }, LBAsect=110169966, high=6, low=9506670, > > > sector=110169951 > > > Nov 20 10:12:16 myth kernel: ide: failed opcode was: unknown > > > Nov 20 10:12:24 myth kernel: hda: dma_intr: status=0x51 { DriveReady > > > SeekComplete Error } > > > Nov 20 10:12:24 myth kernel: hda: dma_intr: error=0x10 { > > > SectorIdNotFound }, LBAsect=110169966, high=6, low=9506670, > > > sector=110169951 > > > Nov 20 10:12:24 myth kernel: ide: failed opcode was: unknown > > > Nov 20 10:12:31 myth kernel: hda: dma_intr: status=0x51 { DriveReady > > > SeekComplete Error } > > > Nov 20 10:12:31 myth kernel: hda: dma_intr: error=0x10 { > > > SectorIdNotFound }, LBAsect=110169966, high=6, low=9506670, > > > sector=110169951 > > > Nov 20 10:12:31 myth kernel: ide: failed opcode was: unknown > > > Nov 20 10:12:31 myth kernel: hda: DMA disabled > > > Nov 20 10:15:18 myth kernel: hdb: DMA disabled > > > Nov 20 10:16:29 myth kernel: ide0: reset: success > > > > > -- > > Adam Hough > > High Performance Computing > > Computing Services Center 200 > > 225-578-7202 > > fax: 225-578-6400 > > ahough@xxxxxxx > > > > -- > > fedora-list mailing list > > fedora-list@xxxxxxxxxx > > To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list > > > > -- > > fedora-list mailing list > > fedora-list@xxxxxxxxxx > > To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list > > >
