Re: FC5 : Failed to allocate memory resource

[alan <alan@xxxxxxxxxxxxxx>]

On Wed, 5 Apr 2006, Dan wrote:

> Gavin Li wrote:
> > I just installed FC5 on my brandnew PC, It prompts the following message 
> > when booting up:
> >
> >
> > Uncompressing liux kernel  OK
> >
> > PCI: Failed to allocate memory resource #6 : 20000:50000000 for 0:01:00.0
> >
> >
> > I did a lspci after bootup:
> >
> > # uname -r
> >
> > 2.6.15-1.2054_FC5smp
> >
> > # lspci
> >
> > 00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub
> >
> > 00:01.0 PCI bridge: Intel Corporation 945G/P PCI Express Graphics Port
> >
> > 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
> > Definition Audio Controller (rev 01)
> >
> > 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> > 1 (rev 01)
> >
> > 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> > 3 (rev 01)
> >
> > 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> > 4 (rev 01)
> >
> > 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 
> > (rev 01)
> >
> > 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 
> > (rev 01)
> >
> > 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 
> > (rev 01)
> >
> > 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 
> > (rev 01)
> >
> > 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
> > Controller (rev 01)
> >
> > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
> >
> > 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC 
> > Interface Bridge (rev 01)
> >
> > 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE 
> > Controller (rev 01)
> >
> > 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial 
> > ATA Storage Controllers cc=IDE (rev 01)
> >
> > 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 
> > 01)
> >
> > 01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] 
> > (rev a2)
> >
> > 05:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 
> > Controller (PHY/Link)
> >
> > 05:08.0 Ethernet controller: Intel Corporation 82801G (ICH7 Family) LAN 
> > Controller (rev 01)
> >
> > #
> >
> >
> > Is this mean the "01:00.0 VGA compatible controller: nVidia Corporation 
> > NV43 [GeForce 6600] (rev a2)" is bad?
> >
> >
> >
> > Gavin
> Does it boot? If it does, I wouldn't worry too much about it; I get this for 
> both the old and new video card in my desktop, and Doom 3 and Quake 4 still 
> run excellently.

I also see this on my HP zv5200 AMD64 laptop, but it is refering to the 
cardbus slot.

PCI: Failed to allocate mem resource #10:2000000@e2000000 for 0000:01:04.0
PCI: Failed to allocate mem resource #10:2000000@e2000000 for 0000:01:04.1
PCI: Bus 2, cardbus bridge: 0000:01:04.0
  IO window: 00003000-000030ff
  IO window: 00003400-000034ff
  PREFETCH window: 50000000-51ffffff
PCI: Bus 6, cardbus bridge: 0000:01:04.1
  IO window: 00003800-000038ff
  IO window: 00003c00-00003cff
  PREFETCH window: 52000000-53ffffff
PCI: Bridge: 0000:00:0a.0
  IO window: 3000-7fff
  MEM window: e0100000-e17fffff
  PREFETCH window: 50000000-53ffffff
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: e2000000-e2ffffff
  PREFETCH window: f0000000-f80fffff


01:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 
01)
01:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 
01)


--
"Remember there is a big difference between kneeling down and bending over." - Frank Zappa