Output from dmesg I see after putting the device in a USB port
immediately after a re-boot is:
usb 1-6: new high speed USB device using address 2
usb 1-6: device not accepting address 2, error -71
usb 1-6: new high speed USB device using address 3
usb 1-6: device not accepting address 3, error -71
If I take it out, and put it back in again, I get the same messages
for address 4 and 5, etc.
I was using the "front" panel USB ports on my PC. I vaguely remember
someone I know having problems with their front panl USB port, so I
tried plugging it into one of the USB ports on the "back" of the PC,
and wonder of wonders, I can see the device and mount it on my FC2 system.
Went to a friends newer Dell desktop running RHEL3 Workstation, it
worked on his system with both the front and back USB port.
Thanks for the trouble you took to reply, appreciate it.
At 03:11 PM 9/19/2005, you wrote:
Gary P Carr wrote:
I am running FC2, don't see anything when I plug the drive in.
You need to know which device it's showing up as. Take a look at the
output of "dmesg" and look for the entries involving that device. It
will probably look something like this:
usb 1-6: new high speed USB device using ehci_hcd and address 4
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: Model: USB FLASH DRIVE Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 2031616 512-byte hdwr sectors (1040 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 2031616 512-byte hdwr sectors (1040 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
If that's the case, it's device "sda" (see last line above). In my
case, partition 1 is used, so:
mount /dev/sda1 /mnt/cdrom
would make it show up as /mnt/cdrom (I just used /mnt/cdrom as an
example...you could mount it as /mnt/floppy or create your own spot
and mount it there).
At 02:43 PM 9/19/2005, you wrote:
Gary P Carr wrote:
How do I get Fedora to recognize and read a Lexar JumpDrive?
Err.... Have you tried plugging it in? FC3 and 4 at least should
automatically find it and mount it for the current logged in user,
older versions should report the new device to the console and
then allow it to be mounted manually.
Jay
--
Jay Lee
Network / Systems Administrator
Information Technology Dept.
Philadelphia Biblical University
--
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
--
----------------------------------------------------------------------
- Rick Stevens, Senior Systems Engineer rstevens@xxxxxxxxxxxxxxx -
- VitalStream, Inc. http://www.vitalstream.com -
- -
- The light at the end of the tunnel is really an oncoming train. -
----------------------------------------------------------------------
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
