This thread seems to be getting top posted, so I'll continue. I've got apcupsd working with FC3 and a Back-UPS RS 1500. These are the lines I needed to edit in /etc/apcupsd/apcupsd.conf:- This UPS is USB only, so set UPSCABLE usb UPSTYPE usb The HID devices have been moved up a directory from /dev/usb/ since I last installed apcupsd on RH9 so change the device line to:- DEVICE /dev/hiddev[0-15] This should get you going, I think. I also set:- BATTERYLEVEL 25 MINUTES 15 but these are down to personal preference. To do a quick test of your installation, set the TIMEOUT parameter to something other than zero. BTW I used:- http://dag.wieers.com/packages/apcupsd/apcupsd-3.10.13-1.1.fc3.rf.i386.rpm to install. Good luck. Dave Fletcher On Tuesday 22 Feb 2005 12:20, javier perez wrote: > ---------- Forwarded message ---------- > From: javier perez <pepebuho.jp@xxxxxxxxx> > Date: Tue, 22 Feb 2005 07:19:45 -0500 > Subject: Re: USB being disconnected on boot FC3 > To: Ankush Grover <ankush174@xxxxxxxxx> > > > Hi > I reinstalled the below mentioned packages. > I still get the disconnect and deregister messages in > /var/log/messages when my computer boots up. > > also, APCUPSD fails to initialize . and an inserted USB Flash also > gets deregistered!!! What can I check to make it work ? > > See attached the boot log messages > eb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.2: OHCI Host Controller > Feb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.2: irq 10, pci mem > 0xf3ffe000 Feb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.2: new USB > bus > registered, assigned bus number 1 > Feb 22 07:07:35 bloody kernel: hub 1-0:1.0: USB hub found > Feb 22 07:07:35 bloody kernel: hub 1-0:1.0: 3 ports detected > Feb 22 07:07:35 bloody kernel: ACPI: PCI interrupt 0000:00:01.3[D] -> > GSI 10 (level, low) -> IRQ 10 > Feb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.3: OHCI Host Controller > Feb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.3: irq 10, pci mem > 0xf3fff000 Feb 22 07:07:35 bloody kernel: ohci_hcd 0000:00:01.3: new USB > bus > registered, assigned bus number 2 > Feb 22 07:07:35 bloody kernel: hub 2-0:1.0: USB hub found > Feb 22 07:07:35 bloody kernel: hub 2-0:1.0: 2 ports detected > Feb 22 07:07:35 bloody kernel: usb 2-1: new low speed USB device using > ohci_hcd and address 2 > Feb 22 07:07:35 bloody kernel: hiddev96: USB HID v1.10 Device [APC > Back-UPS ES 500 FW:801.e5.D USB FW:e5] on usb-0000:00:01.3-1 > Feb 22 07:07:35 bloody kernel: usb 2-2: new full speed USB device > using ohci_hcd and address 3 > Feb 22 07:07:36 bloody kernel: SCSI subsystem initialized > Feb 22 07:07:36 bloody kernel: Initializing USB Mass Storage driver... > Feb 22 07:07:36 bloody kernel: scsi0 : SCSI emulation for USB Mass > Storage devices > Feb 22 07:07:36 bloody kernel: usbcore: registered new driver usb-storage > Feb 22 07:07:36 bloody kernel: USB Mass Storage support registered. > Feb 22 07:07:36 bloody kernel: ohci_hcd 0000:00:01.2: remove, state 1 > Feb 22 07:07:36 bloody kernel: usb usb1: USB disconnect, address 1 > Feb 22 07:07:36 bloody kernel: ohci_hcd 0000:00:01.2: USB bus 1 > deregistered Feb 22 07:07:36 bloody kernel: ohci_hcd 0000:00:01.3: remove, > state 1 Feb 22 07:07:36 bloody kernel: usb usb2: USB disconnect, address 1 > Feb 22 07:07:36 bloody kernel: usb 2-1: USB disconnect, address 2 > Feb 22 07:07:36 bloody kernel: usb 2-2: USB disconnect, address 3 > Feb 22 07:07:36 bloody kernel: ohci_hcd 0000:00:01.3: USB bus 2 > deregistered . > > On Mon, 21 Feb 2005 17:38:17 +0530, Ankush Grover <ankush174@xxxxxxxxx> wrote: > > hey, > > http://www.oracle.com/technology/pub/columns/datta_deploy.html > > did you update ur kernel,hotplug,usdutilits,udev etc. rpms if not > > first update them. > > > > Regards > > > > Ankush > > > > On Mon, 21 Feb 2005 06:27:36 -0500, javier perez <pepebuho.jp@xxxxxxxxx> wrote: > > > Hi > > > > > > I thought I had a problem with my UPS but it turns out to be a larger > > > problem with USB in general. > > > > > > I had FC2 and the UPS worked fine. > > > > > > Then I upgraded to FC3 and several updates later, USB is not working > > > with my UPS. > > > In fact, it seems not to be working. > > > > > > Here is the dmesg info. It seems that usb finds my UPS, but then all > > > usb's are disconnected! > > > > > > I searched on the net, I found a similar question on FedoraForum but no > > > answers. > > > > > > Thanks for your help > > > I have the 2.6.10-1.766_FC3 kernel, > > > > > > Javier > > > > > > [root@bloody ~]# dmesg |grep usb > > > usbcore: registered new driver usbfs > > > usbcore: registered new driver hub > > > usbcore: registered new driver hiddev > > > usbcore: registered new driver usbhid > > > drivers/usb/input/hid-core.c: v2.0:USB HID core driver > > > usb 2-1: new low speed USB device using ohci_hcd and address 2 > > > hiddev96: USB HID v1.10 Device [APC Back-UPS ES 500 FW:801.e5.D USB > > > FW:e5] on usb-0000:00:01.3-1 > > > usb usb1: USB disconnect, address 1 > > > usb usb2: USB disconnect, address 1 > > > usb 2-1: USB disconnect, address 2 > > > [root@bloody ~]# > > > > > > -- > > > ------------------------------ > > > /\_/\ > > > > > > |O O| pepebuho.jp@xxxxxxxxx > > > > > > ~~~~ Javier Perez > > > ~~~~ While the night runs > > > ~~~~ toward the day... > > > m m Pepebuho watches > > > from his high perch. > > > > > > -- > > > fedora-list mailing list > > > fedora-list@xxxxxxxxxx > > > To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list > > -- > ------------------------------ > /\_/\ > > |O O| pepebuho.jp@xxxxxxxxx > > ~~~~ Javier Perez > ~~~~ While the night runs > ~~~~ toward the day... > m m Pepebuho watches > from his high perch. > > > -- > ------------------------------ > /\_/\ > > |O O| pepebuho.jp@xxxxxxxxx > > ~~~~ Javier Perez > ~~~~ While the night runs > ~~~~ toward the day... > m m Pepebuho watches > from his high perch.
