> On Tue, 01 Feb 2005 19:52:31 +0100, Eric Tanguy > <eric.tanguy@xxxxxxxxxxxxxx> wrote: > > Le mardi 01 fÃvrier 2005 Ã 13:11 +0000, Simon Andrews a Ãcrit : > > > Eric Tanguy wrote: > > > > Le dimanche 30 janvier 2005 Ã 20:18 +0100, Eric Tanguy a Ãcrit : > > > > > > > >>My bt878 capture card worked before but now with the last updated kernel > > > >>i can't have it to work. I have no /dev/video*. What could be the > > > >>problem ? > > > >> > > > >>Thanks > > > >>Eric > > > > > > > > When i launch sudo modprobe bttv > > > > FATAL: Error inserting bttv > > > > (/lib/modules/2.6.10-1.741_FC3/kernel/drivers/media/video/bttv.ko): > > > > Unknown symbol in module, or unknown parameter (see dmesg) > > > > > > > > And in dmesg : > > > > bttv: Unknown parameter `' > > > > > > This sounds familiar - others have reported the same message for > > > different modules. I belive that the new kernel is more picky about the > > > formatting of modprobe.conf. Specifically it barfs if there are extra > > > spaces at the end of any of the lines. Try deleting any trailing spaces > > > on lines in modprobe.conf and trying again. > > > > > > Simon. > > > > > Now the problem is that i receive nothing using tvtime. > > I have this in demsg : > > Linux video capture interface: v1.00 > > bttv: driver version 0.9.15 loaded > > bttv: using 8 buffers with 2080k (520 pages) each for capture > > bttv: Bt8xx card found (0). > > ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 11 (level, low) -> IRQ 11 > > bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 11, latency: 64, mmio: > > 0xeb800000 > > bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012 > > bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected] > > bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init] > > tda9885/6/7: chip found @ 0x96 > > bttv0: i2c: checking for MSP34xx @ 0x80... not found > > bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no > > bttv0: using tuner=33 > > bttv0: i2c: checking for MSP34xx @ 0x80... not found > > bttv0: i2c: checking for TDA9875 @ 0xb0... not found > > bttv0: i2c: checking for TDA7432 @ 0x8a... not found > > bttv0: registered device video0 > > bttv0: registered device vbi0 > > bttv0: PLL: 28636363 => 35468950 . ok > > bttv0: timeout: drop=338 irq=6288/30866, risc=1c07c03c, bits: HSYNC > > OFLOW FDSR > > bttv0: reset, reinitialize > > bttv0: PLL: 28636363 => 35468950 . ok > > bttv0: timeout: drop=595 irq=28513/83359, risc=05d5303c, bits: HSYNC > > OFLOW > > bttv0: reset, reinitialize > > bttv0: PLL: 28636363 => 35468950 . ok > > bttv0: timeout: drop=856 irq=31193/91527, risc=05d5303c, bits: HSYNC > > OFLOW FBUS FDSR > > bttv0: reset, reinitialize > > bttv0: PLL: 28636363 => 35468950 . ok > > > > someone have similar pbs with tv card ? > > Le mardi 01 fÃvrier 2005 Ã 14:21 -0500, Travis Osterman a Ãcrit : > If your card has a hardware encoder you might try > $ cat /dev/video0 > /tmp/test.mpg > [ctrl+C to stop] > $ mplayer /tmp/test.mpg > > to determine whether it's a card issue or a tvtime issue. I use the > ivtv driver with my pvr-250 card. Good luck. > > -- Travis > > My card doesn't seem to have a hardware encoder but my card works fine under winxp (double boot). So it could be a tvtime problem but i tried a lot of tv viewer with the same result. It could also be a driver pb. I believe to have seen in this list other people who have pbs with bttv driver and the last kernel but i can't find this thread. Eric -- Eric Tanguy | Nantes, France <eric.tanguy@xxxxxxxxxxxxxx> Key : A4B8368F | Key Server : subkeys.pgp.net Fedora Core release 3 (Heidelberg) sur athlon kernel 2.6.10-1.741_FC3
Attachment:
signature.asc
Description: Ceci est une partie de message =?ISO-8859-1?Q?num=E9riquement?= =?ISO-8859-1?Q?_sign=E9e?=
