On Sun, 14 Nov 2004 23:31:50 +0100, Oliver Kiessler <oliver.kiessler@xxxxxxxxx> wrote: > thanks, jonathan! I found out that I have "cpuspeed" running. when I > do something CPU intensive, the higher frequency is being used. > > bash-3.00$ cat /proc/cpuinfo > processor : 0 > vendor_id : GenuineIntel > cpu family : 15 > model : 2 > model name : Mobile Intel(R) Pentium(R) 4 CPU 3.06GHz > stepping : 9 > cpu MHz : 3057.131 > cache size : 512 KB > fdiv_bug : no > hlt_bug : no > f00f_bug : no > coma_bug : no > fpu : yes > fpu_exception : yes > cpuid level : 2 > wp : yes > flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca > cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid > xtpr > bogomips : 6045.69 > > On Sun, 14 Nov 2004 16:22:50 -0600, Jonathan Berry <berryja@xxxxxxxxx> wrote: > > Hi Oliver, > > > > On Sun, 14 Nov 2004 23:07:38 +0100, Oliver Kiessler > > > > > > <oliver.kiessler@xxxxxxxxx> wrote: > > > the directory exits. this is what it says: > > > > > > [root@stmarks cpufreq]# ls > > > cpuinfo_cur_freq scaling_available_governors scaling_max_freq > > > cpuinfo_max_freq scaling_cur_freq scaling_min_freq > > > cpuinfo_min_freq scaling_driver scaling_setspeed > > > scaling_available_frequencies scaling_governor > > > > > > [root@stmarks cpufreq]# cat cpuinfo_cur_freq > > > 1599960 > > > > > > [root@stmarks cpufreq]# cat cpuinfo_max_freq > > > 3066590 > > > > > > [root@stmarks cpufreq]# cat cpuinfo_min_freq > > > 1599960 > > > > > > [root@stmarks cpufreq]# cat scaling_available_frequencies > > > 3066590 1599960 > > > > > > [root@stmarks cpufreq]# cat scaling_available_governors > > > userspace performance > > > > > > [root@stmarks cpufreq]# cat scaling_cur_freq > > > 1599960 > > > > > > [root@stmarks cpufreq]# cat scaling_driver > > > speedstep-ich > > > > > > [root@stmarks cpufreq]# cat scaling_governor > > > userspace > > > > > > [root@stmarks cpufreq]# cat scaling_max_freq > > > 3066590 > > > > > > [root@stmarks cpufreq]# cat scaling_min_freq > > > 1599960 > > > > > > [root@stmarks cpufreq]# cat scaling_setspeed > > > 1599960 > > > > > > regards, > > > oliver > > > > > > > Okay, good. Now, do you have a frequency scaling governor running? > > If you do and you do something CPU intensive (say, bzip2 a large file, > > or compile a program or something), then you should see the frequency > > in /proc/cpuinfo, scaling_cur_freq, and scaling_setspeed change to the > > higher frequency while it is doing something. Afterwards, it will > > fall back down. If this works, then everything is okay and you will > > use your 3.06 GHz when you need it, and use less power at 1.6 Ghz when > > you don't. > > > > If you cannot seem to get it to go to the higher frequecy, try as root: > > cat scaling_max_freq > scaling_setspeed > > in the same directory as above. If you are then running at the higher > > frequency, then you probably do not have a governor installed. > > Perhaps try "yum install cpufreqd" or look around for another > > governor. I'm not sure what all is available for a Mobile P4. > > > > Jonathan > > > > PS. You need to add the mailing list to the To: addresses when > > responding, since I'm sending this directly to you as well. Do your CPU overclocked ?
