Re: scsi problem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



first thing I'd fix is find a free irq and re-jumper the scsi card for
it.  A lot of older devices just won't work right without an irq,
despite what the driver says.

also, verifying that you can detect the scanner wuold be good. I don't
see any specific mention of the scanner being detected.

cd /proc/scsi
and explore the files under there. one should list the name of your
scanner.  If not, then even though the driver is loaded, the scanner
isn't being seen. I'd suspect something wrong with the driver and/or
the card.

Any possibility you could buy a new pci scsi card? they're awfully
cheap these days.  I doubt the scsi scanner would need more than a
narrow 20MB/s controller.

   - Kevin

On Sun, 15 Aug 2004 11:35:51 +0200, Huub van Niekerk
<v.niekerk@xxxxxxxxx> wrote:
> Hi,
> 
> I've compiled a custom kernel so I should be able to use my scanner. Now
> dmesg shows this:
> 
> > SCSI subsystem initialized
> > Initializing USB Mass Storage driver...
> > scsi0 : SCSI emulation for USB Mass Storage devices
> >   Vendor: PHILIPS   Model: JR24CDRW          Rev: P1.1
> >   Type:   CD-ROM                             ANSI SCSI revision: 02
> > USB Mass Storage device found at 2
> > usbcore: registered new driver usb-storage
> > USB Mass Storage support registered.
> > USB Universal Host Controller Interface driver v2.2
> > ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
> > uhci_hcd 0000:00:07.2: UHCI Host Controller
> > sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda pop-up
> > Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> 
> and
> 
> > Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 5
> > kudzu: Using deprecated /dev/sg mechanism instead of SG_IO on the
> > actual device
> 
> and
> 
> > scsi1 : IRQ0 not free, interrupts disabled
> > scsi1 : interrupts not enabled. for better interactive performance,
> > scsi1 : please jumper the board for a free IRQ.
> > scsi1 : at port 0x280 interrupts disabled options CAN_QUEUE=16
> > CMD_PER_LUN=2 release=1 generic options AUTOPROBE_IRQ AUTOSENSE
> > USLEEP, USLEEP_POLL=1 USLEEP_SLEEP=20 generic release=7
> > scsi1 : Generic NCR5380/53C400 Driver
> > sane-find-scann: Using deprecated /dev/sg mechanism instead of SG_IO
> > on the actual device
> > sane-find-scann: Using deprecated /dev/sg mechanism instead of SG_IO
> > on the actual device
> > sane-find-scann: Using deprecated /dev/sg mechanism instead of SG_IO
> > on the actual device
> > usb 1-3: usbfs: USBDEVFS_CONTROL failed cmd sane-find-scann rqt 128 rq
> > 6 len 100 ret -32
> > usb 1-3: usbfs: USBDEVFS_CONTROL failed cmd sane-find-scann rqt 128 rq
> > 6 len 100 ret -32
> 
> So ny question is actually how I can make sane-find-scanner look for the
> scsi1, i.e. my scanner, instead of my CD-RW drive.
> 
> Thanks
> 
> Huub
> 
> --
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>



[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux