Dear Sergio, I have got quite interesting problem with Fedora Linux. When I installed the Fedora Core 1 on 2-Xeon-processor machine with ServerWorks Grand Champion SL chipset, everything was Ok. But when I tried to install the Fedora Core 2, I received the "Unsupported ServerWorks chipset" message. The vendor of motherboard (Tiger GC-SL S2727) is TYAN Computer Corporation and I didn't find the proper support of this chipset for Linux. Now, I would like to know if this chipset is being supported in Fedora Core release 1.92 or Fedora Core release 2.90. Thanks in advance. Best Regards, Alexander Lazarev Systems Specialist Systems and Database Support Unit International Data Centre Division CTBTO Preparatory Commission Phone: + 43 1 260 30 6368 Fax: + 43 1 260 30 5932 Email: alexander.lazarev@xxxxxxxxx -----Original Message----- From: fedora-list-bounces@xxxxxxxxxx [mailto:fedora-list-bounces@xxxxxxxxxx] On Behalf Of Sergio fernandez Sent: Thursday, July 22, 2004 10:33 AM To: For users of Fedora Core releases Subject: Re: <solved>[RE: Cannot install FC2 or FC3-test1 on 29160 SCSIadapter (no html this time)] Hi mate I have FC2 running on a Adaptec SCSI 19160 connected to a SCSI HD. I found that updating the Adaptec SCSI bios/firmware on the card helped. Also In the PC bios I set the primary chain detection to SCSI instead of the default IDE. I also updated the PC bios to the latest firmware. Hope this helps On 20 Jul 2004, at 20:17, Kartoz, Michael F wrote: >> FC2 is not detecting my hard drive on a 29160 SCSI adapter during >> install. Can anyone help? >> >> I'm trying to install FC2 on a machine with only 1 hard drive that is >> attached to an Adaptec 29160 SCSI controller. The AIC-7xxx driver is >> automatically loading and is finding my adapter (I can see this by >> hitting <F4> while module is loading. However, my disk drive is not >> found. When I get to automatically partitioning, I get "no drives >> found". I had no problems installing and running Redhat 9.0 >> previously on this machine. I also tried FC3-test1 but it didn't >> help. >> >> When I hit <F4> while AIC-7XXX module is loading on FC2, I get the >> following: >> <6>PCI: Found IRQ 5 for device 0000:00:0d.0 >> <6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 >> <4> <Adaptec 29160 Ultra160 SCSI adapter> >> <4> aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs >> <4> >> <4>(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16 >> bit) >> <4>scsi0: Unexpected busfree while idle >> <4>SEQADDR == 0x1 >> > > The solution is to use noprobe when booting the install CD and then > manually add the aic7xxx_old driver (instead of aic7xxx). I had seen > mention of using this driver to solve installation issues on older > Redhat distributions but could not find this driver on FC2. Turns out > that it is in there but appears alphabetically under "O" for Old > adaptec... and I was only looking in the "adaptec" section of the list. > Thanks to all who provided suggestions! > > -Mike > > > -- > fedora-list mailing list > fedora-list@xxxxxxxxxx > To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list > Sergio Fernandez Senior Technical Support Albion - Internet Solutions for Business Hp Centre of Excellence www.albion.co.uk Authorised AppleCentre Tel: 020 7550 7550 Business Class ISP fax: 020 7550 7551 Confidentiality Notice:- This email is intended only for the addressee. If you have received this email in error you are hereby notified that any use, copying or dissemination of this communication is prohibited as it may contain privileged and/or confidential information. Please telephone us immediately on 020 7550 7550 if you are not the intended recipient and destroy the original message. -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
