Hi!
After upgrading to FC2 my system (Athlon 1.2Ghz, 756MB) started to
freeze after an hour or so of work. On all occasions I had to reboot the
system and the last message in the system log was similar to:
May 28 12:38:49 mimas kernel: usb 1-2: USB disconnect, address 2
May 28 12:38:49 mimas kernel: usb 1-2: new low speed USB device using
address 3
May 28 12:38:50 mimas kernel: input: USB HID v1.00 Mouse [Microsoft
Microsoft IntelliMouse Explorer] on usb-0000:00:11.2-2
May 28 12:44:46 mimas syslogd 1.4.1: restart.
So I removed the USB mouse and so far it works fine with old PS2 one.
Can I do anything about it?
I attach kernel log if that helps.
Regards, Igor
Linux version 2.6.5-1.358 (bhcompile@xxxxxxxxxxxxxxxxxxxxx) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 Sat May 8 09:04:50 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000dc000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff8000 (ACPI data)
BIOS-e820: 000000002fff8000 - 0000000030000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
767MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 196592
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192496 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI disabled because your bios is from 97 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: ro root=/dev/hda3
mapped 4G/4G trampoline to ffff3000.
Initializing CPU#0
CPU 0 irqstacks, hard=02345000 soft=02344000
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 1333.250 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 776484k/786368k available (1540k kernel code, 9124k reserved, 599k data, 144k init, 0k highmem)
Calibrating delay loop... 2621.44 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
Failure registering capabilities with the kernel
selinux_register_security: Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f1ff c1c7f9ff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) Processor stepping 04
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb51, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: ACPI tables contain no PCI IRQ routing entries
PCI: Invalid ACPI-PCI IRQ routing table
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3074] at 0000:00:11.0
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1085753464.4294965724:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: AGP aperture is 64M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L040AVER07-0, ATA DISK drive
hdb: WDC WD800JB-00CRA1, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY CD-RW CRX220E1, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=65535/16/63, UDMA(100)
hda: hda1 hda2 hda3
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: hdb1 hdb2 hdb3
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
usbcore: registered new driver hiddev
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 183k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 144k freed
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: irq 5, io base 0000c800
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: irq 5, io base 0000cc00
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:11.4: UHCI Host Controller
uhci_hcd 0000:00:11.4: irq 5, io base 0000d000
uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3
usb 1-2: new low speed USB device using address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:11.2-2
usb 2-2: new full speed USB device using address 2
divert: allocating divert_blk for usb0
usb0: register usbnet at usb-0000:00:11.3-2, Genesys GeneLink
usbcore: registered new driver usbnet
EXT3 FS on hda3, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@xxxxxxxxxxxxxx
Adding 1004052k swap on /dev/hdb2. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
SCSI subsystem initialized
inserting floppy driver for 2.6.5-1.358
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:07.0: 3Com PCI 3c905C Tornado at 0xd800. Vers LK1.1.19
divert: allocating divert_blk for eth0
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:07.0: 3Com PCI 3c905C Tornado at 0xd800. Vers LK1.1.19
divert: allocating divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
NET: Registered protocol family 10
Disabled Privacy Extensions on device 022db720(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using address 3
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:11.2-2
usb 1-2: USB disconnect, address 3
input: PS/2 Logitech Mouse on isa0060/serio1
PCI: Setting latency timer of device 0000:00:11.5 to 64
