Hi, I had also some trouble after upgrading from FC1 to FC2 on my Dell C800. I run system-config-display after installation and got the following working xorg.conf file (see Attachment) . xorg.conf must be in /etx/X11 Hope this will help. Reinhard On Tue, 2004-05-25 at 22:53, Ed Gurski wrote: > I was previously running FC1 and decided to upgrade to FC2. My Dell > laptop has an ATI Radeon Mobilty video card. When I installed FC2 it > could not detect my monitor, so I set it to a Dell Flat Panel for > laptop. I also set the resolution to 1280 x 1024 (my previous settings). > > When FC2 boots, it gives me the boot GUI and then when X starts I get > the message tha another X server is running on Display 0? I'm a little > confused here since I thought it should start on Display 7. > > I try to get it to start on D:7, but all I see is the big X with nothing > else. > > If this has already been resolved, could someone point me to the thread > and I thank you. >
# Xorg configuration created by system-config-display Section "ServerLayout" Identifier "single head configuration" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" # RgbPath is the location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. # Multiple FontPath entries are allowed (they are concatenated together) # By default, Red Hat 6.0 and later now use a font server independent of # the X server to render fonts. RgbPath "/usr/X11R6/lib/X11/rgb" FontPath "unix/:7100" EndSection Section "Module" Load "dbe" Load "extmod" Load "fbdevhw" Load "glx" Load "record" Load "freetype" Load "type1" Load "dri" EndSection Section "InputDevice" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # To disable the XKEYBOARD extension, uncomment XkbDisable. # Option "XkbDisable" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # Or if you just want both to be control, use: # Option "XkbOptions" "ctrl:nocaps" # Identifier "Keyboard0" Driver "keyboard" Option "XkbModel" "pc105" Option "XkbLayout" "de" Option "XkbVariant" "nodeadkeys" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "IMPS/2" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5" Option "Emulate3Buttons" "no" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "LCD Panel 1280x1024" HorizSync 31.5 - 67.0 VertRefresh 50.0 - 75.0 Option "dpms" EndSection Section "Device" Identifier "Videocard0" Driver "r128" VendorName "Videocard vendor" BoardName "ATI Rage 128 Mobility" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection
