Not to be contrary, but wouldn't it be just as easy to do a make rpm then cd /usr/src/redhat/RPMS/i386 rpm -i <kernelpkg> and then run new-kernel-pkg --depmod --mkinitrd --install <version> This handles the grub modification, the module build, the mkinitrd creation, etc. While what you are doing is perfectly legitimate, this saves some steps and take the possibility of error out of the user's hands. Mike Hatzel -----Original Message----- From: Geoffrey Leach [mailto:geoff@xxxxxxxxxxxx] Sent: Tuesday, May 25, 2004 3:24 PM To: Fedora List Subject: Building a 2.6.6 kernel What follows is a short course on building your own kernel, using the released sources from kernel.org. Keep in mind, that with the freedom of DIY builds comes responsibility. If you don't build all of the SCSI controller modules, for instance, you won't be able to drop in a new SCSI card and have it "just work". Also, you can't complain to the good folks who make the ernel rpms when your new kernel breaks. OK. With all of that in mind, you've installed FC2, and you want to roll your own. Here's what you do. o Check the functioning of your rescue disk. Boot with "linux rescue" From the Fedora Core 2 Install disk 1 or DVD and make sure that you can get a your hard disk. Nothing that I write here should make your system unbootable, unless, of course, you don't have a rescue disk. :-) o Go to ftp://ftp.kernel.org/pub/linux/kernel/2.6 and download the latest kernel source. This may or may not be the same thing as found in the kernel-source-2.6.x rpm (when it becomes available), depending on whether or not it was build with patches. o Unpack the kernel source file into /usr/src/linux. o When your FC2 kernel was installed, a kernel config file was installed in /boot. Something like /boot/config-2.6.5-1.358 Copy this file to /usr/src/linux/.config o Check that you have all of config options. Cd to /usr/src/linux. # make oldconfig This will present any configuration options that are not in your .config file. It's safe to accept the default (hit return) for all of them. o nVidia users: check the configuration. If you say, # make help you'll see that there are a number of helpful make targets. The one you want here is gconfig (if you run Gnome/gtk) or xconfig (if you prefer Qt). # make gconfig This opens a new window that permits you to fiddle the kernelr configuration. Open the "kernel hacking" section and check that the "Use 4Kb for kernel stack instead of 8Kb 4KSTACKS" options is unchecked. If not, uncheck it by doubleclicking on the box. (This for gconfig. xconfig may be different). Now go to "Processor type and features", and within that to "Firmware Drivers". Make sure that "Use register arguments (EXPERIMENTAL) REGPARM" is unchecked. o Name the kernel. Edit the Makefile. At the top, you'll see: VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 6 EXTRAVERSION = ... or something similar. If you wish to tag you kernel, set EXTRAVERSION, otherwise, clear it. I use "EXTRAVERSION=ex" o Compile the kernel. # make all You should not see any fatal errors. o Install the kernel. I've appennded a script that I use that makes this easy to do. Copy the script to /usr/src/linux, and change VERSION as appropriate. You want to use the same values as set in the kernel Makefile here. DO NOT USE THE SAME NAME AS YOUR EXISTING KERNEL. # ./install o Make a backup copy of /boot/grub/grub.conf. If you should somehow trash the file in the next step, you will need this (and your rescue disk) to restore the system. o Add a stanza to /boot/grub/grub.conf. If you have a standard Fecora grub.conf, it should say default=0, which means that the default kernel is the first title entry. Copy the first entry somewhere below (so your new kernel is NOT the default) and modify the title, kernel and initrd entries to match your new version. You'll see the new title on the kernel-selection screen when you boot next. You should also replace "rhgb quiet" with vga=all. This will allow you to select console properties maximize the amount of infromation you can see. I use vga=780 which gets me 60 linex x 132 characters. o Reboot and select your new kernel. If you're an nVidia user, nothings that you have done at this point affects your graphics. One thing at a time. ==== The install script #! /bin/sh VERSION=2.6.6ex make modules_install cp -vf bzImage /boot/vmlinuz-${VERSION} cp -vf System.map /boot/System.map-${VERSION} mkinitrd -f -/boot/initrd-${VERSION}.img ${VERSION}
