Daniel Stonier wrote:
You may need to edit your modules.conf and rc.local Have you i2c-proc showing up with an 'lsmod'? I added a few modprobes to the end of my rc.local and an alias in the modules.conf to get it going.
I had problems with FC's rpm's. Ended up removing the lm_sensors rpm and downloading the latest i2c and lm_sensors tarballs and followed the following procedure without any hassles.
- Unpack both tarballs. - Make, Make install on i2c first, then lm_sensors second. - depmod -a - Check /usr/local/bin is in ld.so.conf - ldconfig - Run /sbin/sensors-detect and update modules.conf and rc.local as directed.
Cheers, Daniel
On Thu, 04 Mar 2004 20:08:30 -0500, Craig <cs007fc@xxxxxxxxxx> wrote:
OK, I know people have talked/questioned/answered this before but the archives are down again and I can't for the life of me remember (I'm having a mental meltdown today) what I need to do. When booting up the lm_sensors fail because it can't find /proc:
Mar 4 13:18:23 alopa lm_sensors: Starting up sensors:
Mar 4 13:18:23 alopa kernel: to serial-pci-info@xxxxxxxxxxxxxxxxxxxxxx
Mar 4 13:18:23 alopa kernel: ttyS04 at port 0xd400 (irq = 16) is a 16550A
Mar 4 13:18:23 alopa kernel: Real Time Clock Driver v1.10e
Mar 4 13:18:23 alopa kernel: floppy0: no floppy controllers found
Mar 4 13:18:23 alopa kernel: NET4: Frame Diverter 0.46
Mar 4 13:18:23 alopa kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Mar 4 13:18:23 alopa kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Mar 4 13:18:23 alopa kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 4 13:18:23 alopa lm_sensors: Can't access /proc file
Mar 4 13:18:23 alopa kernel: VP_IDE: IDE controller at PCI slot 00:0f.1
Mar 4 13:18:23 alopa kernel: VP_IDE: chipset revision 6
Mar 4 13:18:23 alopa kernel: VP_IDE: not 100%% native mode: will probe irqs later
Mar 4 13:18:23 alopa lm_sensors:
Mar 4 13:18:23 alopa kernel: VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.1
Mar 4 13:18:23 alopa lm_sensors: Unable to find i2c bus information;
Mar 4 13:18:23 alopa kernel: ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:DMA
Mar 4 13:18:23 alopa lm_sensors: For 2.6 kernels, make sure you have mounted sysfs!
Mar 4 13:18:23 alopa kernel: ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:DMA
Mar 4 13:18:23 alopa lm_sensors: For older kernels, make sure you have done 'modprobe i2c-proc'!
Mar 4 13:18:23 alopa kernel: hda: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
Mar 4 13:18:23 alopa rc: Starting lm_sensors: failed
Nope, i2c-proc is not loaded at all. :-( Where did you find lm_sensors and i2c sources, my search came up empty.
Craig
