Enable enclosure management via LED
As described in the AHCI spec, some AHCI controllers may support
Enclosure management via a variety of protocols. This patch
adds support for the LED message type that is specified in
AHCI 1.1 and higher.
Signed-off-by: Kristen Carlson Accardi <[email protected]>
---
drivers/ata/ahci.c | 153 +++++++++++++++++++++++++++++++++++++++++++++-
drivers/ata/libata-scsi.c | 5 -
include/linux/libata.h | 3
3 files changed, 157 insertions(+), 4 deletions(-)
Index: 2.6-git/drivers/ata/ahci.c
===================================================================
--- 2.6-git.orig/drivers/ata/ahci.c 2007-10-16 16:31:55.000000000 -0700
+++ 2.6-git/drivers/ata/ahci.c 2007-10-17 18:17:28.000000000 -0700
@@ -43,6 +43,7 @@
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_device.h>
#include <linux/libata.h>
#define DRV_NAME "ahci"
@@ -88,6 +89,8 @@ enum {
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
+ HOST_EM_LOC = 0x1c, /* Enclosure Management location */
+ HOST_EM_CTL = 0x20, /* Enclosure Management Control */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
@@ -95,6 +98,7 @@ enum {
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
+ HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
@@ -185,6 +189,10 @@ enum {
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
AHCI_LFLAG_COMMON = ATA_LFLAG_SKIP_D2H_BSY,
+
+ /* em_ctl bits */
+ EM_CTL_RST = (1 << 9), /* Reset */
+ EM_CTL_TM = (1 << 8), /* Transmit Message */
};
struct ahci_cmd_hdr {
@@ -208,6 +216,7 @@ struct ahci_host_priv {
u32 port_map; /* port map to use */
u32 saved_cap; /* saved initial cap */
u32 saved_port_map; /* saved initial port_map */
+ u32 em_loc; /* enclosure management location */
};
struct ahci_port_priv {
@@ -223,6 +232,7 @@ struct ahci_port_priv {
unsigned int ncq_saw_dmas:1;
unsigned int ncq_saw_sdb:1;
u32 intr_mask; /* interrupts to enable */
+ u16 led_state; /* saved current led state */
};
static int ahci_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
@@ -521,6 +531,9 @@ static struct pci_driver ahci_pci_driver
#endif
};
+static int ahci_em_messages = 1;
+module_param(ahci_em_messages, int, 0444);
+MODULE_PARM_DESC(ahci_em_messages, "Set AHCI Enclosure Management Message type (0 = disabled, 1 = LED, 2 = SAF-TE, 3 = SES-2, 4 = SGPIO)");
static inline int ahci_nr_ports(u32 cap)
{
@@ -902,6 +915,120 @@ static int ahci_reset_controller(struct
return 0;
}
+/****** LED Enclosure Management routines ********/
+static int ahci_reset_em(struct ata_host *host)
+{
+ void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
+ u32 em_ctl;
+
+ em_ctl = readl(mmio + HOST_EM_CTL);
+ if ((em_ctl & EM_CTL_TM) || (em_ctl & EM_CTL_RST))
+ return -EINVAL;
+
+ writel(em_ctl | EM_CTL_RST, mmio + HOST_EM_CTL);
+ return 0;
+}
+
+static int ahci_transmit_led_message(struct ata_port *ap, int led_num,
+ int state)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = ap->host->iomap[AHCI_PCI_BAR];
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 em_ctl;
+ u32 message[] = {0,0};
+
+ /*
+ * if we are still busy transmitting a previous message,
+ * do not allow
+ */
+ em_ctl = readl(mmio + HOST_EM_CTL);
+ if (em_ctl & EM_CTL_TM)
+ return -EINVAL;
+
+ /*
+ * create message header - this is all zero except for
+ * the message size, which is 4 bytes.
+ */
+ message[0] |= (4 << 8);
+
+ pp->led_state &= ~(9 << (3*led_num));
+
+ /*
+ * create the actual message
+ * XXX will need Port Multiplier support
+ */
+ message[1] = (ap->port_no | (pp->led_state << 16));
+
+ /* LED bit locations are determined by the led_num */
+ message[1] |= (state << (16 + (3*led_num)));
+
+ /* write message to EM_LOC */
+ writel(message[0], mmio + hpriv->em_loc);
+ writel(message[1], mmio + hpriv->em_loc+4);
+
+ /* save off new led state */
+ pp->led_state = ((message[1] >> 16) & 0x00ff);
+
+ /*
+ * tell hardware to transmit the message
+ */
+ writel(em_ctl | EM_CTL_TM, mmio + HOST_EM_CTL);
+ return 0;
+}
+
+static ssize_t ahci_led_locate_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct scsi_device *sdev = to_scsi_device(dev);
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
+ int state;
+ int rc;
+
+ if (!atadev || !ata_dev_enabled(atadev))
+ return -EINVAL;
+
+ state = simple_strtoul(buf, NULL, 0);
+ if (state != 0 && state != 1)
+ return -EINVAL;
+
+ rc = ahci_transmit_led_message(ap, 1, state);
+ if (!rc)
+ return count;
+ return rc;
+}
+static DEVICE_ATTR(locate, S_IWUGO, NULL, ahci_led_locate_store);
+
+static ssize_t ahci_led_fault_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct scsi_device *sdev = to_scsi_device(dev);
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
+ int state;
+ int rc;
+
+ if (!atadev || !ata_dev_enabled(atadev))
+ return -EINVAL;
+
+ state = simple_strtoul(buf, NULL, 0);
+ if (state != 0 && state != 1)
+ return -EINVAL;
+
+ rc = ahci_transmit_led_message(ap, 2, state);
+ if (!rc)
+ return count;
+ return rc;
+}
+static DEVICE_ATTR(fault, S_IWUGO, NULL, ahci_led_fault_store);
+
+static struct device_attribute *ahci_em_led_attrs[] = {
+ &dev_attr_locate,
+ &dev_attr_fault,
+ NULL
+};
+
static void ahci_port_init(struct pci_dev *pdev, struct ata_port *ap,
int port_no, void __iomem *mmio,
void __iomem *port_mmio)
@@ -1934,7 +2061,7 @@ static void ahci_print_info(struct ata_h
dev_printk(KERN_INFO, &pdev->dev,
"flags: "
"%s%s%s%s%s%s%s"
- "%s%s%s%s%s%s%s\n"
+ "%s%s%s%s%s%s%s%s\n"
,
cap & (1 << 31) ? "64bit " : "",
@@ -1951,7 +2078,8 @@ static void ahci_print_info(struct ata_h
cap & (1 << 17) ? "pmp " : "",
cap & (1 << 15) ? "pio " : "",
cap & (1 << 14) ? "slum " : "",
- cap & (1 << 13) ? "part " : ""
+ cap & (1 << 13) ? "part " : "",
+ cap & (1 << 6) ? "ems ": ""
);
}
@@ -2036,6 +2164,27 @@ static int ahci_init_one(struct pci_dev
ahci_init_controller(host);
ahci_print_info(host);
+ if (ahci_em_messages && (hpriv->cap & HOST_CAP_EMS)) {
+ u8 messages;
+ void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
+ u32 em_loc = readl(mmio + HOST_EM_LOC);
+ u32 em_ctl = readl(mmio + HOST_EM_CTL);
+
+ messages = (em_ctl & 0x000f0000) >> 16;
+
+ /* we only support LED message type right now */
+ if ((messages & 0x01) && (ahci_em_messages == 1)) {
+ /* store em_loc */
+ hpriv->em_loc = ((em_loc >> 16) * 4);
+
+ /* reset the LEDs */
+ ahci_reset_em(host);
+
+ /* modify sht to add led sysfs files */
+ ahci_sht.sdev_attrs = ahci_em_led_attrs;
+ }
+ }
+
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, ahci_interrupt, IRQF_SHARED,
&ahci_sht);
Index: 2.6-git/include/linux/libata.h
===================================================================
--- 2.6-git.orig/include/linux/libata.h 2007-10-16 16:31:55.000000000 -0700
+++ 2.6-git/include/linux/libata.h 2007-10-16 16:32:16.000000000 -0700
@@ -185,6 +185,7 @@ enum {
ATA_FLAG_ACPI_SATA = (1 << 17), /* need native SATA ACPI layout */
ATA_FLAG_AN = (1 << 18), /* controller supports AN */
ATA_FLAG_PMP = (1 << 19), /* controller supports PMP */
+ ATA_FLAG_EM = (1 << 20), /* Enclosure Management support */
/* The following flag belongs to ap->pflags but is kept in
* ap->flags because it's referenced in many LLDs and will be
@@ -870,6 +871,8 @@ extern int ata_scsi_slave_config(struct
extern void ata_scsi_slave_destroy(struct scsi_device *sdev);
extern int ata_scsi_change_queue_depth(struct scsi_device *sdev,
int queue_depth);
+struct ata_device * ata_scsi_find_dev(struct ata_port *ap,
+ const struct scsi_device *scsidev);
extern struct ata_device *ata_dev_pair(struct ata_device *adev);
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern u8 ata_irq_on(struct ata_port *ap);
Index: 2.6-git/drivers/ata/libata-scsi.c
===================================================================
--- 2.6-git.orig/drivers/ata/libata-scsi.c 2007-10-16 16:31:55.000000000 -0700
+++ 2.6-git/drivers/ata/libata-scsi.c 2007-10-16 16:33:20.000000000 -0700
@@ -55,7 +55,7 @@ typedef unsigned int (*ata_xlat_func_t)(
static struct ata_device * __ata_scsi_find_dev(struct ata_port *ap,
const struct scsi_device *scsidev);
-static struct ata_device * ata_scsi_find_dev(struct ata_port *ap,
+struct ata_device * ata_scsi_find_dev(struct ata_port *ap,
const struct scsi_device *scsidev);
static int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel,
unsigned int id, unsigned int lun);
@@ -2544,7 +2544,7 @@ static int ata_scsi_dev_enabled(struct a
* RETURNS:
* Associated ATA device, or %NULL if not found.
*/
-static struct ata_device *
+struct ata_device *
ata_scsi_find_dev(struct ata_port *ap, const struct scsi_device *scsidev)
{
struct ata_device *dev = __ata_scsi_find_dev(ap, scsidev);
@@ -2554,6 +2554,7 @@ ata_scsi_find_dev(struct ata_port *ap, c
return dev;
}
+EXPORT_SYMBOL_GPL(ata_scsi_find_dev);
/*
* ata_scsi_map_proto - Map pass-thru protocol value to taskfile value.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
