Re: Q: PCI-X @ 266MHz on HP rx6600 (Qlogic 4Gb FC HBA)

[Andrew Vasquez <andrew.vasquez@qlogic.com>]

On Thu, 26 Jul 2007, Andrew Patterson wrote:

> On Thu, 2007-07-26 at 15:36 +0200, Ulrich Windl wrote:
> > Hi,
> > 
> > I have a question: The Qlogic ISP2422 chip is said to handle PCI-X 266MHz. So does 
> > the HP Itanium2 server rx6600. Basically that was the reason to select that 
> > server. The FC-HBA is in a 266 MHz capable slot. However when booting SLES10 SP1 
> > for IA64, the logs say:

There's a mixup here in terminology...  The QLA2460 card which you
have does in fact support 'PCI-X 266'...

> > <6>QLogic Fibre Channel HBA Driver
> > <6>GSI 49 (level, low) -> CPU 3 (0x0300) vector 51
> > <6>ACPI: PCI Interrupt 0000:0f:01.0[A] -> GSI 49 (level, low) -> IRQ 51
> > <6>qla2xxx 0000:0f:01.0: Found an ISP2422, irq 51, iobase 0xc0000000b0040000
> > [...]
> > <6>qla2xxx 0000:0f:01.0: LOOP UP detected (4 Gbps).
> > <6>qla2xxx 0000:0f:01.0: Topology - (F_Port), Host Loop address 0x0
> > <6>scsi0 : qla2xxx
> > <6>qla2xxx 0000:0f:01.0:
> > <4> QLogic Fibre Channel HBA Driver: 8.01.07-k3
> > <4>  QLogic HP AB378-60001 -
> > <4>  ISP2422: PCI-X Mode 2 (133 MH4.00.26 [IP]  @ 0000:0f:01.0 hdma+, host#=0, 
> > fw=4.00.26 [IP]

The 33/66/100/133 values refer to the bus-clock speed at which the
card is operating.  As is seen here (although a bit truncated --
separate issue, I'll try to see if I can reproduce this on one of my
HPQ rigs), the card is inserted into a PCI-X Mode-2 capable 133MHz
(bus clock) slot.  When operating under this mode, each data-phase
between two devices is divided into 2 sub-phases, effectively doubling
the transfer-data-rate to 266Mhz.

> > <5>  Vendor: HP        Model: HSV200            Rev: 6100
> > <5>  Type:   RAID                               ANSI SCSI revision: 02
> > <5> 0:0:0:0: Attached scsi generic sg0 type 12
> > 
> > Now does Linux support the speed of 266 MHz, and is it just displayed incorrectly, 
> > or doesn't Linux support the speed of 266MHz yet?
> 
> This is a bug in the driver.  The lookup table only goes to 133 MHz.
> 
> static char *pci_bus_modes[] = {
>                 "33", "66", "100", "133",
> 
> The same problem exists in the scsi_misc tree.

Regards,
Andrew Vasquez
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/