Re: [PATCH] mmc: at91_mci: fix hanging and rework to match flowcharts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Pierre Ossman :
Nicolas Ferre wrote:
Fixes hanging using multi block operations (seen during CMD25).
Follows closely the datasheet flowcharts.

This piece of code handles better big file writing. I had to take care
of the notbusy signal during write (at91_mci_handle_cmdrdy function) and
to rearrange the AT91_MCI_ENDRX and AT91_MCI_RXBUFF flag usage.

Signed-off-by: Nicolas Ferre <[email protected]>
---

Most of the patch looks ok. Do you want to wait for some more tests or should I
chuck this into the imminent merge window?

*pong*

I think it is ok to put it into the merge window.

@@ -817,7 +834,11 @@ static int __init at91_mci_probe(struct
    mmc->ops = &at91_mci_ops;
    mmc->f_min = 375000;
-    mmc->f_max = 25000000;
+    if (cpu_is_at91sam9263())
+        mmc->f_max = 50000000;
+    else
+        mmc->f_max = 25000000;
+
    mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
    mmc->caps = MMC_CAP_BYTEBLOCK | MMC_CAP_MULTIWRITE;


This seems unrelated to the rest of the patch. Also, high-speed won't be enabled
unless you set the appropriate caps (which should be checked against timing
specifications, not just assigned and hope for the best).

True. I remove this chunk off the patch.


@@ -830,11 +851,11 @@ static int __init at91_mci_probe(struct
    host->bus_mode = 0;
    host->board = pdev->dev.platform_data;
    if (host->board->wire4) {
-#ifdef SUPPORT_4WIRE
-        mmc->caps |= MMC_CAP_4_BIT_DATA;
-#else
-        printk("AT91 MMC: 4 wire bus mode not supported by this driver
- using 1 wire\n");
-#endif
+        if (cpu_is_at91sam9260() || cpu_is_at91sam9263())
+            mmc->caps |= MMC_CAP_4_BIT_DATA;
+        else
+            printk("AT91 MMC: 4 wire bus mode not supported"
+                " - using 1 wire\n");
    }

    /*


This also looks unrelated.

Well, It is related to capacities of newer IPs that allow readproof and writeproof features that I enable here :

+	if (cpu_is_at91sam9260() || cpu_is_at91sam9263())
+		mr |= AT91_MCI_RDPROOF | AT91_MCI_WRPROOF;

This allows to have a smooth data transmission internally (prevent underruns) and so have full 4 wires capacity. So I think this is good for having a full featured driver on all chips.

I resend a corrected patch now.

Regards,
--
Nicolas Ferre


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux