[POSSIBLE BUG]: tg3 network is "lost"

Hello everybody.

This is a second post, because title was wrong on the first post. Please
excuse my english, i'm french.

I have a big trouble with several server, web server. They are all
debian sarge based.

Program that run on tem are principally Apache2, PHP5, Zend cluster with
session management, Postfix and NFS client


Theses servers work well and, suddendly, one of them lost network.

Let me describe when i say "lost network":
- The server doesn't answer to a ping, all network application on it
doesn't anwer too
- The server can't ping another server, or make another network connection
- The server loose NFS communication with the NFS server
- On the console, if i type ifconfig i see the interface configured with
it's own IP
- On the console if i launch iptraf i only see icmp host unrechable message
- On the console if i type "mii-tool" it say that link is 100FX
negociated and link is UP
- The only way i have found to solve the trouble is to launch
"/etc/init.d/network restart". the network come back.
- When the server "lost" network, i don't have any message even with
debug activated on kernel
- When i restart network, i have these kernel message (seems to be
"normal"):

92554.221511] PM: Writing back config space on device 0000:02:02.0 at
offset b (was 164814e4, writing d00e11)
[492554.221528] PM: Writing back config space on device 0000:02:02.0 at
offset 3 (was 804000, writing 804010)
[492554.221534] PM: Writing back config space on device 0000:02:02.0 at
offset 2 (was 2000000, writing 2000010)
[492554.221540] PM: Writing back config space on device 0000:02:02.0 at
offset 1 (was 2b00000, writing 2b00146)
[492554.525866] PM: Writing back config space on device 0000:02:02.0 at
offset b (was 164814e4, writing d00e11)
[492554.525883] PM: Writing back config space on device 0000:02:02.0 at
offset 3 (was 804000, writing 804010)
[492554.525889] PM: Writing back config space on device 0000:02:02.0 at
offset 2 (was 2000000, writing 2000010)
[492554.525895] PM: Writing back config space on device 0000:02:02.0 at
offset 1 (was 2b00000, writing 2b00146)
[492556.321312] tg3: eth0: Link is up at 100 Mbps, full duplex.
[492556.321334] tg3: eth0: Flow control is on for TX and on for RX.


- Theses server are IP statics (not DHCP client).
- This is not cable or switch trouble (servers are on different switch)
- They are kernel 2.6.19.3, but we have the same trouble with other
kernel like 2.6.17.1


I attach you some information about server, like lspci -vvv, config.gz.


Thanks for reading me and for your help.

Attachment: config.gz
Description: application/gzip

0000:00:00.0 Host bridge: Intel Corp. Server Memory Controller Hub (rev 0c)
	Subsystem: Compaq Computer Corporation: Unknown device 3200
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [40] #09 [4105]

0000:00:02.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port A0 (rev 0c) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=00, secondary=0d, subordinate=0f, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
		Address: fee00000  Data: 0000
	Capabilities: [64] #10 [0041]

0000:00:04.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port B0 (rev 0c) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=00, secondary=06, subordinate=0c, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
		Address: fee00000  Data: 0000
	Capabilities: [64] #10 [0041]

0000:00:06.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express Port C0 (rev 0c) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=00, secondary=03, subordinate=05, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
		Address: fee00000  Data: 0000
	Capabilities: [64] #10 [0041]

0000:00:1c.0 PCI bridge: Intel Corp. 6300ESB 64-bit PCI-X Bridge (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
	I/O behind bridge: 00004000-00004fff
	Memory behind bridge: fdf00000-fdffffff
	Prefetchable memory behind bridge: 00000000e2000000-00000000e2000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] PCI-X bridge device.
		Secondary Status: 64bit+, 133MHz-, SCD-, USC-, SCO-, SRD- Freq=1
		Status: Bus=0 Dev=28 Func=0 64bit+ 133MHz- SCD- USC-, SCO-, SRD-
		: Upstream: Capacity=65535, Commitment Limit=0
		: Downstream: Capacity=65535, Commitment Limit=0

0000:00:1d.0 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02) (prog-if 00 [UHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at 5000 [size=32]

0000:00:1d.1 USB Controller: Intel Corp. 6300ESB USB Universal Host Controller (rev 02) (prog-if 00 [UHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 5020 [size=32]

0000:00:1d.4 System peripheral: Intel Corp. 6300ESB Watchdog Timer (rev 02)
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Region 0: Memory at fbef0000 (32-bit, non-prefetchable) [size=16]

0000:00:1d.5 PIC: Intel Corp. 6300ESB I/O Advanced Programmable Interrupt Controller (rev 02) (prog-if 20 [IO(X)-APIC])
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [50] PCI-X non-bridge device.
		Command: DPERE- ERO- RBC=0 OST=0
		Status: Bus=0 Dev=29 Func=5 64bit+ 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-

0000:00:1d.7 USB Controller: Intel Corp. 6300ESB USB2 Enhanced Host Controller (rev 02) (prog-if 20 [EHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin D routed to IRQ 23
	Region 0: Memory at fbee0000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] #0a [2080]

0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 0a) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 00001000-00003fff
	Memory behind bridge: fbf00000-fcffffff
	Prefetchable memory behind bridge: e2100000-e21fffff
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

0000:00:1f.0 ISA bridge: Intel Corp. 6300ESB LPC Interface Controller (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

0000:00:1f.1 IDE interface: Intel Corp. 6300ESB PATA Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
	Subsystem: Compaq Computer Corporation: Unknown device 3201
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at <ignored>
	Region 1: I/O ports at <ignored>
	Region 2: I/O ports at <ignored>
	Region 3: I/O ports at <ignored>
	Region 4: I/O ports at 0500 [size=16]
	Region 5: Memory at e2200000 (32-bit, non-prefetchable) [size=1K]

0000:01:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
	Subsystem: Compaq Computer Corporation: Unknown device 001e
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min), Cache Line Size: 0x10 (64 bytes)
	Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at 3000 [size=256]
	Region 2: Memory at fbff0000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at e2100000 [disabled] [size=128K]
	Capabilities: [5c] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:04.0 System peripheral: Compaq Computer Corporation Integrated Lights Out Controller (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device b206
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at 1800 [size=256]
	Region 1: Memory at fbfe0000 (32-bit, non-prefetchable) [size=512]
	Capabilities: [f0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:04.2 System peripheral: Compaq Computer Corporation Integrated Lights Out  Processor (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device b206
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin B routed to IRQ 22
	Region 0: I/O ports at 3400 [size=256]
	Region 1: Memory at fbfd0000 (32-bit, non-prefetchable) [size=2K]
	Region 2: Memory at fbfc0000 (32-bit, non-prefetchable) [size=8K]
	Region 3: Memory at fbf00000 (32-bit, non-prefetchable) [size=512K]
	Expansion ROM at e2120000 [disabled] [size=64K]
	Capabilities: [f0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

0000:02:01.0 RAID bus controller: Compaq Computer Corporation Smart Array 64xx (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device 4091
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 24
	Region 0: Memory at fdff0000 (64-bit, non-prefetchable) [size=8K]
	Region 2: I/O ports at 4000 [size=256]
	Region 3: Memory at fdf80000 (64-bit, non-prefetchable) [size=256K]
	Expansion ROM at e2000000 [disabled] [size=256K]
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [dc] PCI-X non-bridge device.
		Command: DPERE- ERO+ RBC=0 OST=4
		Status: Bus=2 Dev=1 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple, DMMRBC=2, DMOST=4, DMCRS=2, RSCEM-
	Capabilities: [f0] Vital Product Data

0000:02:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
	Subsystem: Compaq Computer Corporation NC7782 Gigabit Server Adapter (PCI-X, 10,100,1000-T)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 25
	Region 0: Memory at fdf70000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] 	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
		Address: 7afffd25fbf79f6c  Data: 7fdc

0000:02:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
	Subsystem: Compaq Computer Corporation NC7782 Gigabit Server Adapter (PCI-X, 10,100,1000-T)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin B routed to IRQ 26
	Region 0: Memory at fdf60000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] 	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
		Address: 0408d1a0bbaf2020  Data: 8c80

0000:06:00.0 PCI bridge: Intel Corp. PCI Bridge Hub A (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=06, secondary=07, subordinate=09, sec-latency=64
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [44] #10 [0071]
	Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [6c] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d8] 
0000:06:00.2 PCI bridge: Intel Corp. PCI Bridge Hub B (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 0x10 (64 bytes)
	Bus: primary=06, secondary=0a, subordinate=0c, sec-latency=64
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
	BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [44] #10 [0071]
	Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [6c] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d8]

Follow-Ups:
- Re: [POSSIBLE BUG]: tg3 network is "lost"
  - From: serge <[email protected]>

Prev by Date: Re: Suspend2 is getting a new name.
Next by Date: Re: Suspend2 is getting a new name.
Previous by thread: Suspend2 is getting a new name.
Next by thread: Re: [POSSIBLE BUG]: tg3 network is "lost"
Index(es):
- Date
- Thread

[Index of Archives] [Kernel Newbies] [Netfilter] [Bugtraq] [Photo] [Stuff] [Gimp] [Yosemite News] [MIPS Linux] [ARM Linux] [Linux Security] [Linux RAID] [Video 4 Linux] [Linux for the blind] [Linux Resources]