From: Jay Cliburn <[email protected]>
From: Chris Snook <[email protected]>
This patch contains the header files needed by the Attansic L1 gigabit
ethernet adapter driver.
Signed-off-by: Jay Cliburn <[email protected]>
Signed-off-by: Chris Snook <[email protected]>
---
atl1.h | 266 +++++++++++++++
atl1_hw.h | 1053 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 1319 insertions(+)
diff --git a/drivers/net/atl1/atl1.h b/drivers/net/atl1/atl1.h
new file mode 100644
index 0000000..9578104
--- /dev/null
+++ b/drivers/net/atl1/atl1.h
@@ -0,0 +1,266 @@
+/**
+ * atl1.h - atl1 main header
+ *
+ * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
+ * Copyright(c) 2006 Chris Snook <[email protected]>
+ * Copyright(c) 2006 Jay Cliburn <[email protected]>
+ *
+ * Derived from Intel e1000 driver
+ * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ **/
+
+#ifndef _ATL1_H_
+#define _ATL1_H_
+
+#include <linux/tcp.h>
+#include <linux/skbuff.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/spinlock_types.h>
+#include <linux/workqueue.h>
+#include <linux/timer.h>
+#include <linux/delay.h>
+#include <linux/if_vlan.h>
+
+#include <asm/types.h>
+#include <asm/atomic.h>
+
+#include "atl1_hw.h"
+
+#ifdef NETIF_F_TSO
+#include <net/checksum.h>
+#endif
+
+#ifdef SIOCGMIIPHY
+#include <linux/mii.h>
+#endif
+
+#ifdef SIOCETHTOOL
+#include <linux/ethtool.h>
+#endif
+
+#define BAR_0 0
+
+/* function prototypes needed by multiple files */
+s32 atl1_up(struct atl1_adapter *adapter);
+void atl1_down(struct atl1_adapter *adapter);
+int atl1_reset(struct atl1_adapter *adapter);
+s32 atl1_setup_ring_resources(struct atl1_adapter *adapter);
+void atl1_free_ring_resources(struct atl1_adapter *adapter);
+
+struct atl1_adapter;
+
+#define ATL1_MAX_INTR 3
+
+#define ATL1_DEFAULT_TPD 256
+#define ATL1_MAX_TPD 1023
+#define ATL1_MIN_TPD 64
+#define ATL1_DEFAULT_RFD 512
+#define ATL1_MIN_RFD 128
+#define ATL1_MAX_RFD 2047
+
+#define ATL1_GET_DESC(R, i, type) (&(((type *)((R)->desc))[i]))
+#define ATL1_RFD_DESC(R, i) ATL1_GET_DESC(R, i, struct rx_free_desc)
+#define ATL1_TPD_DESC(R, i) ATL1_GET_DESC(R, i, struct tx_packet_desc)
+#define ATL1_RRD_DESC(R, i) ATL1_GET_DESC(R, i, struct rx_return_desc)
+
+#define usec_delay(x) udelay(x)
+#ifndef msec_delay
+#define msec_delay(x) do { if(in_interrupt()) { \
+ /* Don't mdelay in interrupt context!*/ \
+ BUG(); \
+ } else { \
+ msleep(x); \
+ }} while(0)
+/**
+ * Some workarounds require millisecond delays and are run during interrupt
+ * context. Most notably, when establishing link, the phy may need tweaking
+ * but cannot process phy register reads/writes faster than millisecond
+ * intervals...and we establish link due to a "link status change" interrupt.
+ **/
+#define msec_delay_irq(x) mdelay(x)
+#endif
+
+/**
+ * wrapper around a pointer to a socket buffer,
+ * so a DMA handle can be stored along with the buffer
+ **/
+struct atl1_buffer {
+ struct sk_buff *skb;
+ u16 length;
+ u16 alloced;
+ dma_addr_t dma;
+};
+
+#define MAX_TX_BUF_LEN 0x3000 /* 12KB */
+
+struct atl1_tpd_ring {
+ void *desc; /* pointer to the descriptor ring memory */
+ dma_addr_t dma; /* physical adress of the descriptor ring */
+ u16 size; /* length of descriptor ring in bytes */
+ u16 count; /* number of descriptors in the ring */
+
+ u16 hw_idx; /* hardware index */
+ atomic_t next_to_clean;
+ atomic_t next_to_use;
+ struct atl1_buffer *buffer_info;
+};
+
+struct atl1_rfd_ring {
+ void *desc;
+ dma_addr_t dma;
+ u16 size;
+ u16 count;
+ atomic_t next_to_use;
+ u16 next_to_clean;
+ struct atl1_buffer *buffer_info;
+};
+
+struct atl1_rrd_ring {
+ void *desc;
+ dma_addr_t dma;
+ unsigned int size;
+ u16 count;
+ u16 next_to_use;
+ atomic_t next_to_clean;
+};
+
+struct atl1_ring_header {
+ /* pointer to the descriptor ring memory */
+ void *desc;
+ /* physical adress of the descriptor ring */
+ dma_addr_t dma;
+ /* length of descriptor ring in bytes */
+ unsigned int size;
+};
+
+struct atl1_cmb {
+ struct coals_msg_block *cmb;
+ dma_addr_t dma;
+};
+
+struct atl1_smb {
+ struct stats_msg_block *smb;
+ dma_addr_t dma;
+};
+
+/* Statistics counters */
+struct atl1_sft_stats {
+ u64 rx_packets;
+ u64 tx_packets;
+ u64 rx_bytes;
+ u64 tx_bytes;
+ u64 multicast;
+ u64 collisions;
+ u64 rx_errors;
+ u64 rx_length_errors;
+ u64 rx_crc_errors;
+ u64 rx_frame_errors;
+ u64 rx_fifo_errors;
+ u64 rx_missed_errors;
+ u64 tx_errors;
+ u64 tx_fifo_errors;
+ u64 tx_aborted_errors;
+ u64 tx_window_errors;
+ u64 tx_carrier_errors;
+
+ u64 tx_pause; /* The number of Pause packet transmitted. */
+ u64 excecol; /* The number of transmit packets aborted due to excessive collisions. */
+ u64 deffer; /* The number of packets transmitted that is deferred. */
+ u64 scc; /* The number of packets subsequently transmitted successfully with a single prior collision. */
+ u64 mcc; /* The number of packets subsequently transmitted successfully with multiple prior collisions. */
+ u64 latecol; /* The number of packets transmitted with late collisions. */
+ u64 tx_underun; /* The number of transmit packets aborted due to transmit FIFO underrun, or TRD FIFO underrun */
+ u64 tx_trunc; /* The number of transmit packets truncated due to size exceeding MTU, regardless if it is truncated by Selene or not.
+ * (The name is not really reflects the meaning in this case here.) */
+ u64 rx_pause; /* The number of Pause packet received. */
+ u64 rx_rrd_ov;
+ u64 rx_trunc;
+};
+
+/* board specific private data structure */
+#define ATL1_REGS_LEN 8
+
+struct atl1_adapter {
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+ struct net_device_stats net_stats;
+ struct atl1_sft_stats soft_stats;
+
+ struct vlan_group *vlgrp;
+ u32 rx_buffer_len;
+ u32 wol;
+ u16 link_speed;
+ u16 link_duplex;
+ spinlock_t stats_lock;
+ spinlock_t tx_lock;
+ spinlock_t vl_lock;
+ spinlock_t mii_lock;
+ atomic_t irq_sem;
+ struct work_struct tx_timeout_task;
+ struct work_struct link_chg_task;
+ struct work_struct pcie_dma_to_rst_task;
+ struct timer_list watchdog_timer;
+ struct timer_list phy_config_timer;
+ bool phy_timer_pending;
+
+ bool mac_disabled;
+
+ /* All descriptor rings' memory */
+ struct atl1_ring_header ring_header;
+
+ /* TX */
+ struct atl1_tpd_ring tpd_ring;
+ spinlock_t mb_lock;
+
+ /* RX */
+ struct atl1_rfd_ring rfd_ring;
+ struct atl1_rrd_ring rrd_ring;
+ u64 hw_csum_err;
+ u64 hw_csum_good;
+
+ u32 gorcl;
+ u64 gorcl_old;
+
+ /* Interrupt Moderator timer ( 2us resolution) */
+ u16 imt;
+ /* Interrupt Clear timer (2us resolution) */
+ u16 ict;
+
+ /* MII interface info */
+ struct mii_if_info mii;
+
+ /* structs defined in atl1_hw.h */
+ u32 bd_number; /* board number */
+ bool pci_using_64;
+ struct atl1_hw hw;
+ struct atl1_smb smb;
+ struct atl1_cmb cmb;
+
+#ifdef ETHTOOL_TEST
+ u32 test_icr;
+ struct atl1_ring_header test_ring_header;
+ struct atl1_tpd_ring test_tpd_ring;
+ struct atl1_rfd_ring test_rfd_ring;
+ struct atl1_rrd_ring test_rrd_ring;
+#endif
+ int enable_msi;
+ u32 pci_state[16];
+};
+
+#endif /* _ATL1_H_ */
diff --git a/drivers/net/atl1/atl1_hw.h b/drivers/net/atl1/atl1_hw.h
new file mode 100644
index 0000000..378b2b4
--- /dev/null
+++ b/drivers/net/atl1/atl1_hw.h
@@ -0,0 +1,1053 @@
+/**
+ * atl1_hw.h - atl1 hardware definitions
+ *
+ * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
+ * Copyright(c) 2006 Chris Snook <[email protected]>
+ * Copyright(c) 2006 Jay Cliburn <[email protected]>
+ *
+ * Derived from Intel e1000 driver
+ * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * There are a lot of defines in here that are unused and/or have cryptic
+ * names. Please leave them alone, as they're the closest thing we have
+ * to a spec from Attansic at present. *ahem* -- CHS
+ **/
+
+#ifndef _ATL1_HW_H_
+#define _ATL1_HW_H_
+
+#define _ATL1_ATTRIB_PACK_ __attribute__ ((packed))
+
+struct atl1_adapter;
+struct atl1_hw;
+
+/* function prototypes needed by multiple files */
+s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw);
+s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data);
+s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 * speed, u16 * duplex);
+s32 atl1_read_mac_addr(struct atl1_hw *hw);
+s32 atl1_init_hw(struct atl1_hw *hw);
+s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 * speed, u16 * duplex);
+s32 atl1_set_speed_and_duplex(struct atl1_hw *hw, u16 speed, u16 duplex);
+u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 * mc_addr);
+void atl1_hash_set(struct atl1_hw *hw, u32 hash_value);
+s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 * phy_data);
+void atl1_set_mac_addr(struct atl1_hw *hw);
+s32 atl1_phy_enter_power_saving(struct atl1_hw *hw);
+s32 atl1_reset_hw(struct atl1_hw *hw);
+void atl1_check_options(struct atl1_adapter *adapter);
+void atl1_set_ethtool_ops(struct net_device *netdev);
+
+/* register definitions */
+#define REG_PCIE_CAP_LIST 0x58
+
+#define REG_VPD_CAP 0x6C
+#define VPD_CAP_ID_MASK 0xff
+#define VPD_CAP_ID_SHIFT 0
+#define VPD_CAP_NEXT_PTR_MASK 0xFF
+#define VPD_CAP_NEXT_PTR_SHIFT 8
+#define VPD_CAP_VPD_ADDR_MASK 0x7FFF
+#define VPD_CAP_VPD_ADDR_SHIFT 16
+#define VPD_CAP_VPD_FLAG 0x80000000
+
+#define REG_VPD_DATA 0x70
+
+#define REG_SPI_FLASH_CTRL 0x200
+#define SPI_FLASH_CTRL_STS_NON_RDY 0x1
+#define SPI_FLASH_CTRL_STS_WEN 0x2
+#define SPI_FLASH_CTRL_STS_WPEN 0x80
+#define SPI_FLASH_CTRL_DEV_STS_MASK 0xFF
+#define SPI_FLASH_CTRL_DEV_STS_SHIFT 0
+#define SPI_FLASH_CTRL_INS_MASK 0x7
+#define SPI_FLASH_CTRL_INS_SHIFT 8
+#define SPI_FLASH_CTRL_START 0x800
+#define SPI_FLASH_CTRL_EN_VPD 0x2000
+#define SPI_FLASH_CTRL_LDSTART 0x8000
+#define SPI_FLASH_CTRL_CS_HI_MASK 0x3
+#define SPI_FLASH_CTRL_CS_HI_SHIFT 16
+#define SPI_FLASH_CTRL_CS_HOLD_MASK 0x3
+#define SPI_FLASH_CTRL_CS_HOLD_SHIFT 18
+#define SPI_FLASH_CTRL_CLK_LO_MASK 0x3
+#define SPI_FLASH_CTRL_CLK_LO_SHIFT 20
+#define SPI_FLASH_CTRL_CLK_HI_MASK 0x3
+#define SPI_FLASH_CTRL_CLK_HI_SHIFT 22
+#define SPI_FLASH_CTRL_CS_SETUP_MASK 0x3
+#define SPI_FLASH_CTRL_CS_SETUP_SHIFT 24
+#define SPI_FLASH_CTRL_EROM_PGSZ_MASK 0x3
+#define SPI_FLASH_CTRL_EROM_PGSZ_SHIFT 26
+#define SPI_FLASH_CTRL_WAIT_READY 0x10000000
+
+#define REG_SPI_ADDR 0x204
+
+#define REG_SPI_DATA 0x208
+
+#define REG_SPI_FLASH_CONFIG 0x20C
+#define SPI_FLASH_CONFIG_LD_ADDR_MASK 0xFFFFFF
+#define SPI_FLASH_CONFIG_LD_ADDR_SHIFT 0
+#define SPI_FLASH_CONFIG_VPD_ADDR_MASK 0x3
+#define SPI_FLASH_CONFIG_VPD_ADDR_SHIFT 24
+#define SPI_FLASH_CONFIG_LD_EXIST 0x4000000
+
+#define REG_SPI_FLASH_OP_PROGRAM 0x210
+#define REG_SPI_FLASH_OP_SC_ERASE 0x211
+#define REG_SPI_FLASH_OP_CHIP_ERASE 0x212
+#define REG_SPI_FLASH_OP_RDID 0x213
+#define REG_SPI_FLASH_OP_WREN 0x214
+#define REG_SPI_FLASH_OP_RDSR 0x215
+#define REG_SPI_FLASH_OP_WRSR 0x216
+#define REG_SPI_FLASH_OP_READ 0x217
+
+#define REG_TWSI_CTRL 0x218
+#define TWSI_CTRL_LD_OFFSET_MASK 0xFF
+#define TWSI_CTRL_LD_OFFSET_SHIFT 0
+#define TWSI_CTRL_LD_SLV_ADDR_MASK 0x7
+#define TWSI_CTRL_LD_SLV_ADDR_SHIFT 8
+#define TWSI_CTRL_SW_LDSTART 0x800
+#define TWSI_CTRL_HW_LDSTART 0x1000
+#define TWSI_CTRL_SMB_SLV_ADDR_MASK 0x7F
+#define TWSI_CTRL_SMB_SLV_ADDR_SHIFT 15
+#define TWSI_CTRL_LD_EXIST 0x400000
+#define TWSI_CTRL_READ_FREQ_SEL_MASK 0x3
+#define TWSI_CTRL_READ_FREQ_SEL_SHIFT 23
+#define TWSI_CTRL_FREQ_SEL_100K 0
+#define TWSI_CTRL_FREQ_SEL_200K 1
+#define TWSI_CTRL_FREQ_SEL_300K 2
+#define TWSI_CTRL_FREQ_SEL_400K 3
+#define TWSI_CTRL_SMB_SLV_ADDR
+#define TWSI_CTRL_WRITE_FREQ_SEL_MASK 0x3
+#define TWSI_CTRL_WRITE_FREQ_SEL_SHIFT 24
+
+#define REG_PCIE_DEV_MISC_CTRL 0x21C
+#define PCIE_DEV_MISC_CTRL_EXT_PIPE 0x2
+#define PCIE_DEV_MISC_CTRL_RETRY_BUFDIS 0x1
+#define PCIE_DEV_MISC_CTRL_SPIROM_EXIST 0x4
+#define PCIE_DEV_MISC_CTRL_SERDES_ENDIAN 0x8
+#define PCIE_DEV_MISC_CTRL_SERDES_SEL_DIN 0x10
+
+/* Selene Master Control Register */
+#define REG_MASTER_CTRL 0x1400
+#define MASTER_CTRL_SOFT_RST 0x1
+#define MASTER_CTRL_MTIMER_EN 0x2
+#define MASTER_CTRL_ITIMER_EN 0x4
+#define MASTER_CTRL_MANUAL_INT 0x8
+#define MASTER_CTRL_REV_NUM_SHIFT 16
+#define MASTER_CTRL_REV_NUM_MASK 0xff
+#define MASTER_CTRL_DEV_ID_SHIFT 24
+#define MASTER_CTRL_DEV_ID_MASK 0xff
+
+/* Timer Initial Value Register */
+#define REG_MANUAL_TIMER_INIT 0x1404
+
+/* IRQ ModeratorTimer Initial Value Register */
+#define REG_IRQ_MODU_TIMER_INIT 0x1408
+
+#define REG_GPHY_ENABLE 0x140C
+
+/* IRQ Anti-Lost Timer Initial Value Register */
+#define REG_CMBDISDMA_TIMER 0x140E
+
+/* Block IDLE Status Register */
+#define REG_IDLE_STATUS 0x1410
+#define IDLE_STATUS_RXMAC 1
+#define IDLE_STATUS_TXMAC 2
+#define IDLE_STATUS_RXQ 4
+#define IDLE_STATUS_TXQ 8
+#define IDLE_STATUS_DMAR 0x10
+#define IDLE_STATUS_DMAW 0x20
+#define IDLE_STATUS_SMB 0x40
+#define IDLE_STATUS_CMB 0x80
+
+/* MDIO Control Register */
+#define REG_MDIO_CTRL 0x1414
+#define MDIO_DATA_MASK 0xffff
+#define MDIO_DATA_SHIFT 0
+#define MDIO_REG_ADDR_MASK 0x1f
+#define MDIO_REG_ADDR_SHIFT 16
+#define MDIO_RW 0x200000
+#define MDIO_SUP_PREAMBLE 0x400000
+#define MDIO_START 0x800000
+#define MDIO_CLK_SEL_SHIFT 24
+#define MDIO_CLK_25_4 0
+#define MDIO_CLK_25_6 2
+#define MDIO_CLK_25_8 3
+#define MDIO_CLK_25_10 4
+#define MDIO_CLK_25_14 5
+#define MDIO_CLK_25_20 6
+#define MDIO_CLK_25_28 7
+#define MDIO_BUSY 0x8000000
+#define MDIO_WAIT_TIMES 30
+
+/* MII PHY Status Register */
+#define REG_PHY_STATUS 0x1418
+
+/* BIST Control and Status Register0 (for the Packet Memory) */
+#define REG_BIST0_CTRL 0x141c
+#define BIST0_NOW 0x1
+#define BIST0_SRAM_FAIL 0x2
+#define BIST0_FUSE_FLAG 0x4
+#define REG_BIST1_CTRL 0x1420
+#define BIST1_NOW 0x1
+#define BIST1_SRAM_FAIL 0x2
+#define BIST1_FUSE_FLAG 0x4
+
+/* MAC Control Register */
+#define REG_MAC_CTRL 0x1480
+#define MAC_CTRL_TX_EN 1
+#define MAC_CTRL_RX_EN 2
+#define MAC_CTRL_TX_FLOW 4
+#define MAC_CTRL_RX_FLOW 8
+#define MAC_CTRL_LOOPBACK 0x10
+#define MAC_CTRL_DUPLX 0x20
+#define MAC_CTRL_ADD_CRC 0x40
+#define MAC_CTRL_PAD 0x80
+#define MAC_CTRL_LENCHK 0x100
+#define MAC_CTRL_HUGE_EN 0x200
+#define MAC_CTRL_PRMLEN_SHIFT 10
+#define MAC_CTRL_PRMLEN_MASK 0xf
+#define MAC_CTRL_RMV_VLAN 0x4000
+#define MAC_CTRL_PROMIS_EN 0x8000
+#define MAC_CTRL_TX_PAUSE 0x10000
+#define MAC_CTRL_SCNT 0x20000
+#define MAC_CTRL_SRST_TX 0x40000
+#define MAC_CTRL_TX_SIMURST 0x80000
+#define MAC_CTRL_SPEED_SHIFT 20
+#define MAC_CTRL_SPEED_MASK 0x300000
+#define MAC_CTRL_SPEED_1000 2
+#define MAC_CTRL_SPEED_10_100 1
+#define MAC_CTRL_DBG_TX_BKPRESURE 0x400000
+#define MAC_CTRL_TX_HUGE 0x800000
+#define MAC_CTRL_RX_CHKSUM_EN 0x1000000
+#define MAC_CTRL_MC_ALL_EN 0x2000000
+#define MAC_CTRL_BC_EN 0x4000000
+#define MAC_CTRL_DBG 0x8000000
+
+/* MAC IPG/IFG Control Register */
+#define REG_MAC_IPG_IFG 0x1484
+#define MAC_IPG_IFG_IPGT_SHIFT 0
+#define MAC_IPG_IFG_IPGT_MASK 0x7f
+#define MAC_IPG_IFG_MIFG_SHIFT 8
+#define MAC_IPG_IFG_MIFG_MASK 0xff
+#define MAC_IPG_IFG_IPGR1_SHIFT 16
+#define MAC_IPG_IFG_IPGR1_MASK 0x7f
+#define MAC_IPG_IFG_IPGR2_SHIFT 24
+#define MAC_IPG_IFG_IPGR2_MASK 0x7f
+
+/* MAC STATION ADDRESS */
+#define REG_MAC_STA_ADDR 0x1488
+
+/* Hash table for multicast address */
+#define REG_RX_HASH_TABLE 0x1490
+
+/* MAC Half-Duplex Control Register */
+#define REG_MAC_HALF_DUPLX_CTRL 0x1498
+#define MAC_HALF_DUPLX_CTRL_LCOL_SHIFT 0
+#define MAC_HALF_DUPLX_CTRL_LCOL_MASK 0x3ff
+#define MAC_HALF_DUPLX_CTRL_RETRY_SHIFT 12
+#define MAC_HALF_DUPLX_CTRL_RETRY_MASK 0xf
+#define MAC_HALF_DUPLX_CTRL_EXC_DEF_EN 0x10000
+#define MAC_HALF_DUPLX_CTRL_NO_BACK_C 0x20000
+#define MAC_HALF_DUPLX_CTRL_NO_BACK_P 0x40000
+#define MAC_HALF_DUPLX_CTRL_ABEBE 0x80000
+#define MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT 20
+#define MAC_HALF_DUPLX_CTRL_ABEBT_MASK 0xf
+#define MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT 24
+#define MAC_HALF_DUPLX_CTRL_JAMIPG_MASK 0xf
+
+/* Maximum Frame Length Control Register */
+#define REG_MTU 0x149c
+
+/* Wake-On-Lan control register */
+#define REG_WOL_CTRL 0x14a0
+#define WOL_PATTERN_EN 0x00000001
+#define WOL_PATTERN_PME_EN 0x00000002
+#define WOL_MAGIC_EN 0x00000004
+#define WOL_MAGIC_PME_EN 0x00000008
+#define WOL_LINK_CHG_EN 0x00000010
+#define WOL_LINK_CHG_PME_EN 0x00000020
+#define WOL_PATTERN_ST 0x00000100
+#define WOL_MAGIC_ST 0x00000200
+#define WOL_LINKCHG_ST 0x00000400
+#define WOL_CLK_SWITCH_EN 0x00008000
+#define WOL_PT0_EN 0x00010000
+#define WOL_PT1_EN 0x00020000
+#define WOL_PT2_EN 0x00040000
+#define WOL_PT3_EN 0x00080000
+#define WOL_PT4_EN 0x00100000
+#define WOL_PT5_EN 0x00200000
+#define WOL_PT6_EN 0x00400000
+
+/* WOL Length ( 2 DWORD ) */
+#define REG_WOL_PATTERN_LEN 0x14a4
+#define WOL_PT_LEN_MASK 0x7f
+#define WOL_PT0_LEN_SHIFT 0
+#define WOL_PT1_LEN_SHIFT 8
+#define WOL_PT2_LEN_SHIFT 16
+#define WOL_PT3_LEN_SHIFT 24
+#define WOL_PT4_LEN_SHIFT 0
+#define WOL_PT5_LEN_SHIFT 8
+#define WOL_PT6_LEN_SHIFT 16
+
+/* Internal SRAM Partition Register */
+#define REG_SRAM_RFD_ADDR 0x1500
+#define REG_SRAM_RFD_LEN (REG_SRAM_RFD_ADDR+ 4)
+#define REG_SRAM_RRD_ADDR (REG_SRAM_RFD_ADDR+ 8)
+#define REG_SRAM_RRD_LEN (REG_SRAM_RFD_ADDR+12)
+#define REG_SRAM_TPD_ADDR (REG_SRAM_RFD_ADDR+16)
+#define REG_SRAM_TPD_LEN (REG_SRAM_RFD_ADDR+20)
+#define REG_SRAM_TRD_ADDR (REG_SRAM_RFD_ADDR+24)
+#define REG_SRAM_TRD_LEN (REG_SRAM_RFD_ADDR+28)
+#define REG_SRAM_RXF_ADDR (REG_SRAM_RFD_ADDR+32)
+#define REG_SRAM_RXF_LEN (REG_SRAM_RFD_ADDR+36)
+#define REG_SRAM_TXF_ADDR (REG_SRAM_RFD_ADDR+40)
+#define REG_SRAM_TXF_LEN (REG_SRAM_RFD_ADDR+44)
+#define REG_SRAM_TCPH_PATH_ADDR (REG_SRAM_RFD_ADDR+48)
+#define SRAM_TCPH_ADDR_MASK 0x0fff
+#define SRAM_TCPH_ADDR_SHIFT 0
+#define SRAM_PATH_ADDR_MASK 0x0fff
+#define SRAM_PATH_ADDR_SHIFT 16
+
+/* Load Ptr Register */
+#define REG_LOAD_PTR (REG_SRAM_RFD_ADDR+52)
+
+/* Descriptor Control register */
+#define REG_DESC_BASE_ADDR_HI 0x1540
+#define REG_DESC_RFD_ADDR_LO (REG_DESC_BASE_ADDR_HI+4)
+#define REG_DESC_RRD_ADDR_LO (REG_DESC_BASE_ADDR_HI+8)
+#define REG_DESC_TPD_ADDR_LO (REG_DESC_BASE_ADDR_HI+12)
+#define REG_DESC_CMB_ADDR_LO (REG_DESC_BASE_ADDR_HI+16)
+#define REG_DESC_SMB_ADDR_LO (REG_DESC_BASE_ADDR_HI+20)
+#define REG_DESC_RFD_RRD_RING_SIZE (REG_DESC_BASE_ADDR_HI+24)
+#define DESC_RFD_RING_SIZE_MASK 0x7ff
+#define DESC_RFD_RING_SIZE_SHIFT 0
+#define DESC_RRD_RING_SIZE_MASK 0x7ff
+#define DESC_RRD_RING_SIZE_SHIFT 16
+#define REG_DESC_TPD_RING_SIZE (REG_DESC_BASE_ADDR_HI+28)
+#define DESC_TPD_RING_SIZE_MASK 0x3ff
+#define DESC_TPD_RING_SIZE_SHIFT 0
+
+/* TXQ Control Register */
+#define REG_TXQ_CTRL 0x1580
+#define TXQ_CTRL_TPD_BURST_NUM_SHIFT 0
+#define TXQ_CTRL_TPD_BURST_NUM_MASK 0x1f
+#define TXQ_CTRL_EN 0x20
+#define TXQ_CTRL_ENH_MODE 0x40
+#define TXQ_CTRL_TPD_FETCH_TH_SHIFT 8
+#define TXQ_CTRL_TPD_FETCH_TH_MASK 0x3f
+#define TXQ_CTRL_TXF_BURST_NUM_SHIFT 16
+#define TXQ_CTRL_TXF_BURST_NUM_MASK 0xffff
+
+/* Jumbo packet Threshold for task offload */
+#define REG_TX_JUMBO_TASK_TH_TPD_IPG 0x1584
+#define TX_JUMBO_TASK_TH_MASK 0x7ff
+#define TX_JUMBO_TASK_TH_SHIFT 0
+#define TX_TPD_MIN_IPG_MASK 0x1f
+#define TX_TPD_MIN_IPG_SHIFT 16
+
+/* RXQ Control Register */
+#define REG_RXQ_CTRL 0x15a0
+#define RXQ_CTRL_RFD_BURST_NUM_SHIFT 0
+#define RXQ_CTRL_RFD_BURST_NUM_MASK 0xff
+#define RXQ_CTRL_RRD_BURST_THRESH_SHIFT 8
+#define RXQ_CTRL_RRD_BURST_THRESH_MASK 0xff
+#define RXQ_CTRL_RFD_PREF_MIN_IPG_SHIFT 16
+#define RXQ_CTRL_RFD_PREF_MIN_IPG_MASK 0x1f
+#define RXQ_CTRL_CUT_THRU_EN 0x40000000
+#define RXQ_CTRL_EN 0x80000000
+
+/* Rx jumbo packet threshold and rrd retirement timer */
+#define REG_RXQ_JMBOSZ_RRDTIM (REG_RXQ_CTRL+ 4)
+#define RXQ_JMBOSZ_TH_MASK 0x7ff
+#define RXQ_JMBOSZ_TH_SHIFT 0
+#define RXQ_JMBO_LKAH_MASK 0xf
+#define RXQ_JMBO_LKAH_SHIFT 11
+#define RXQ_RRD_TIMER_MASK 0xffff
+#define RXQ_RRD_TIMER_SHIFT 16
+
+/* RFD flow control register */
+#define REG_RXQ_RXF_PAUSE_THRESH (REG_RXQ_CTRL+ 8)
+#define RXQ_RXF_PAUSE_TH_HI_SHIFT 16
+#define RXQ_RXF_PAUSE_TH_HI_MASK 0xfff
+#define RXQ_RXF_PAUSE_TH_LO_SHIFT 0
+#define RXQ_RXF_PAUSE_TH_LO_MASK 0xfff
+
+/* RRD flow control register */
+#define REG_RXQ_RRD_PAUSE_THRESH (REG_RXQ_CTRL+12)
+#define RXQ_RRD_PAUSE_TH_HI_SHIFT 0
+#define RXQ_RRD_PAUSE_TH_HI_MASK 0xfff
+#define RXQ_RRD_PAUSE_TH_LO_SHIFT 16
+#define RXQ_RRD_PAUSE_TH_LO_MASK 0xfff
+
+/* DMA Engine Control Register */
+#define REG_DMA_CTRL 0x15c0
+#define DMA_CTRL_DMAR_IN_ORDER 0x1
+#define DMA_CTRL_DMAR_ENH_ORDER 0x2
+#define DMA_CTRL_DMAR_OUT_ORDER 0x4
+#define DMA_CTRL_RCB_VALUE 0x8
+#define DMA_CTRL_DMAR_BURST_LEN_SHIFT 4
+#define DMA_CTRL_DMAR_BURST_LEN_MASK 7
+#define DMA_CTRL_DMAW_BURST_LEN_SHIFT 7
+#define DMA_CTRL_DMAW_BURST_LEN_MASK 7
+#define DMA_CTRL_DMAR_EN 0x400
+#define DMA_CTRL_DMAW_EN 0x800
+
+/* CMB/SMB Control Register */
+#define REG_CSMB_CTRL 0x15d0
+#define CSMB_CTRL_CMB_NOW 1
+#define CSMB_CTRL_SMB_NOW 2
+#define CSMB_CTRL_CMB_EN 4
+#define CSMB_CTRL_SMB_EN 8
+
+/* CMB DMA Write Threshold Register */
+#define REG_CMB_WRITE_TH (REG_CSMB_CTRL+ 4)
+#define CMB_RRD_TH_SHIFT 0
+#define CMB_RRD_TH_MASK 0x7ff
+#define CMB_TPD_TH_SHIFT 16
+#define CMB_TPD_TH_MASK 0x7ff
+
+/* RX/TX count-down timer to trigger CMB-write. 2us resolution. */
+#define REG_CMB_WRITE_TIMER (REG_CSMB_CTRL+ 8)
+#define CMB_RX_TM_SHIFT 0
+#define CMB_RX_TM_MASK 0xffff
+#define CMB_TX_TM_SHIFT 16
+#define CMB_TX_TM_MASK 0xffff
+
+/* Number of packet received since last CMB write */
+#define REG_CMB_RX_PKT_CNT (REG_CSMB_CTRL+12)
+
+/* Number of packet transmitted since last CMB write */
+#define REG_CMB_TX_PKT_CNT (REG_CSMB_CTRL+16)
+
+/* SMB auto DMA timer register */
+#define REG_SMB_TIMER (REG_CSMB_CTRL+20)
+
+/* Mailbox Register */
+#define REG_MAILBOX 0x15f0
+#define MB_RFD_PROD_INDX_SHIFT 0
+#define MB_RFD_PROD_INDX_MASK 0x7ff
+#define MB_RRD_CONS_INDX_SHIFT 11
+#define MB_RRD_CONS_INDX_MASK 0x7ff
+#define MB_TPD_PROD_INDX_SHIFT 22
+#define MB_TPD_PROD_INDX_MASK 0x3ff
+
+/* Interrupt Status Register */
+#define REG_ISR 0x1600
+#define ISR_SMB 1
+#define ISR_TIMER 2
+#define ISR_MANUAL 4
+#define ISR_RXF_OV 8
+#define ISR_RFD_UNRUN 0x10
+#define ISR_RRD_OV 0x20
+#define ISR_TXF_UNRUN 0x40
+#define ISR_LINK 0x80
+#define ISR_HOST_RFD_UNRUN 0x100
+#define ISR_HOST_RRD_OV 0x200
+#define ISR_DMAR_TO_RST 0x400
+#define ISR_DMAW_TO_RST 0x800
+#define ISR_GPHY 0x1000
+#define ISR_RX_PKT 0x10000
+#define ISR_TX_PKT 0x20000
+#define ISR_TX_DMA 0x40000
+#define ISR_RX_DMA 0x80000
+#define ISR_CMB_RX 0x100000
+#define ISR_CMB_TX 0x200000
+#define ISR_MAC_RX 0x400000
+#define ISR_MAC_TX 0x800000
+#define ISR_UR_DETECTED 0x1000000
+#define ISR_FERR_DETECTED 0x2000000
+#define ISR_NFERR_DETECTED 0x4000000
+#define ISR_CERR_DETECTED 0x8000000
+#define ISR_PHY_LINKDOWN 0x10000000
+#define ISR_DIS_SMB 0x20000000
+#define ISR_DIS_DMA 0x40000000
+#define ISR_DIS_INT 0x80000000
+
+/* Interrupt Mask Register */
+#define REG_IMR 0x1604
+
+/* Normal Interrupt mask */
+#define IMR_NORMAL_MASK (\
+ ISR_SMB |\
+ ISR_GPHY |\
+ ISR_PHY_LINKDOWN|\
+ ISR_DMAR_TO_RST |\
+ ISR_DMAW_TO_RST |\
+ ISR_CMB_TX |\
+ ISR_CMB_RX )
+
+/* Debug Interrupt Mask (enable all interrupt) */
+#define IMR_DEBUG_MASK (\
+ ISR_SMB |\
+ ISR_TIMER |\
+ ISR_MANUAL |\
+ ISR_RXF_OV |\
+ ISR_RFD_UNRUN |\
+ ISR_RRD_OV |\
+ ISR_TXF_UNRUN |\
+ ISR_LINK |\
+ ISR_CMB_TX |\
+ ISR_CMB_RX |\
+ ISR_RX_PKT |\
+ ISR_TX_PKT |\
+ ISR_MAC_RX |\
+ ISR_MAC_TX )
+
+/* Interrupt Status Register */
+#define REG_RFD_RRD_IDX 0x1800
+#define REG_TPD_IDX 0x1804
+
+/* MII definition */
+/* PHY Common Register */
+#define MII_BMCR 0x00
+#define MII_BMSR 0x01
+#define MII_PHYSID1 0x02
+#define MII_PHYSID2 0x03
+#define MII_ADVERTISE 0x04
+#define MII_LPA 0x05
+#define MII_EXPANSION 0x06
+#define MII_AT001_CR 0x09
+#define MII_AT001_SR 0x0A
+#define MII_AT001_ESR 0x0F
+#define MII_AT001_PSCR 0x10
+#define MII_AT001_PSSR 0x11
+#define MII_DCOUNTER 0x12
+#define MII_FCSCOUNTER 0x13
+#define MII_NWAYTEST 0x14
+#define MII_RERRCOUNTER 0x15
+#define MII_SREVISION 0x16
+#define MII_RESV1 0x17
+#define MII_LBRERROR 0x18
+#define MII_PHYADDR 0x19
+#define MII_RESV2 0x1a
+#define MII_TPISTATUS 0x1b
+#define MII_NCONFIG 0x1c
+
+/* PHY Control Register */
+#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+#define MII_CR_SPEED_MASK 0x2040
+#define MII_CR_SPEED_1000 0x0040
+#define MII_CR_SPEED_100 0x2000
+#define MII_CR_SPEED_10 0x0000
+
+/* PHY Status Register */
+#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
+#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
+
+/* Link partner ability register. */
+#define MII_LPA_SLCT 0x001f /* Same as advertise selector */
+#define MII_LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
+#define MII_LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
+#define MII_LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
+#define MII_LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
+#define MII_LPA_100BASE4 0x0200 /* 100BASE-T4 */
+#define MII_LPA_PAUSE 0x0400 /* PAUSE */
+#define MII_LPA_ASYPAUSE 0x0800 /* Asymmetrical PAUSE */
+#define MII_LPA_RFAULT 0x2000 /* Link partner faulted */
+#define MII_LPA_LPACK 0x4000 /* Link partner acked us */
+#define MII_LPA_NPAGE 0x8000 /* Next page bit */
+
+/* Autoneg Advertisement Register */
+#define MII_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
+#define MII_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define MII_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define MII_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define MII_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define MII_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
+#define MII_AR_PAUSE 0x0400 /* Pause operation desired */
+#define MII_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+#define MII_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
+#define MII_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+#define MII_AR_SPEED_MASK 0x01E0
+#define MII_AR_DEFAULT_CAP_MASK 0x0DE0
+
+/* 1000BASE-T Control Register */
+#define MII_AT001_CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define MII_AT001_CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+#define MII_AT001_CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port, 0=DTE device */
+#define MII_AT001_CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master, 0=Configure PHY as Slave */
+#define MII_AT001_CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value, 0=Automatic Master/Slave config */
+#define MII_AT001_CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define MII_AT001_CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
+#define MII_AT001_CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
+#define MII_AT001_CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
+#define MII_AT001_CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
+#define MII_AT001_CR_1000T_SPEED_MASK 0x0300
+#define MII_AT001_CR_1000T_DEFAULT_CAP_MASK 0x0300
+
+/* 1000BASE-T Status Register */
+#define MII_AT001_SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
+#define MII_AT001_SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
+#define MII_AT001_SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define MII_AT001_SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+#define MII_AT001_SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
+#define MII_AT001_SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
+#define MII_AT001_SR_1000T_REMOTE_RX_STATUS_SHIFT 12
+#define MII_AT001_SR_1000T_LOCAL_RX_STATUS_SHIFT 13
+
+/* Extended Status Register */
+#define MII_AT001_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
+#define MII_AT001_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
+#define MII_AT001_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
+#define MII_AT001_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
+
+/* AT001 PHY Specific Control Register */
+#define MII_AT001_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
+#define MII_AT001_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define MII_AT001_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
+#define MII_AT001_PSCR_MAC_POWERDOWN 0x0008
+#define MII_AT001_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low, 0=CLK125 toggling */
+#define MII_AT001_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5, Manual MDI configuration */
+#define MII_AT001_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+#define MII_AT001_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
+#define MII_AT001_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled all speeds. */
+#define MII_AT001_PSCR_10BT_EXT_DIST_ENABLE 0x0080 /* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T RX Threshold), 0=Normal 10BASE-T RX Threshold */
+#define MII_AT001_PSCR_MII_5BIT_ENABLE 0x0100 /* 1=5-Bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
+#define MII_AT001_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
+#define MII_AT001_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
+#define MII_AT001_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+#define MII_AT001_PSCR_POLARITY_REVERSAL_SHIFT 1
+#define MII_AT001_PSCR_AUTO_X_MODE_SHIFT 5
+#define MII_AT001_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7
+
+/* AT001 PHY Specific Status Register */
+#define MII_AT001_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define MII_AT001_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define MII_AT001_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define MII_AT001_PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define MII_AT001_PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define MII_AT001_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+/* PCI Command Register Bit Definitions */
+#define PCI_REG_COMMAND 0x04 /* PCI Command Register */
+#define CMD_IO_SPACE 0x0001
+#define CMD_MEMORY_SPACE 0x0002
+#define CMD_BUS_MASTER 0x0004
+
+/* Wake Up Filter Control */
+#define ATL1_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define ATL1_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define ATL1_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define ATL1_WUFC_MC 0x00000008 /* Multicast Wakeup Enable */
+#define ATL1_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+
+/* Error Codes */
+#define ATL1_SUCCESS 0
+#define ATL1_ERR_EEPROM 1
+#define ATL1_ERR_PHY 2
+#define ATL1_ERR_CONFIG 3
+#define ATL1_ERR_PARAM 4
+#define ATL1_ERR_MAC_TYPE 5
+#define ATL1_ERR_PHY_TYPE 6
+#define ATL1_ERR_PHY_SPEED 7
+#define ATL1_ERR_PHY_RES 8
+
+#define SPEED_0 0xffff
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+#define MEDIA_TYPE_AUTO_SENSOR 0
+#define MEDIA_TYPE_1000M_FULL 1
+#define MEDIA_TYPE_100M_FULL 2
+#define MEDIA_TYPE_100M_HALF 3
+#define MEDIA_TYPE_10M_FULL 4
+#define MEDIA_TYPE_10M_HALF 5
+
+#define ADVERTISE_10_HALF 0x0001
+#define ADVERTISE_10_FULL 0x0002
+#define ADVERTISE_100_HALF 0x0004
+#define ADVERTISE_100_FULL 0x0008
+#define ADVERTISE_1000_HALF 0x0010
+#define ADVERTISE_1000_FULL 0x0020
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
+#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */
+#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */
+
+/* The size (in bytes) of a ethernet packet */
+#define ENET_HEADER_SIZE 14
+#define MAXIMUM_ETHERNET_FRAME_SIZE 1518 /* with FCS */
+#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* with FCS */
+#define ETHERNET_FCS_SIZE 4
+#define MAX_JUMBO_FRAME_SIZE 0x2800
+
+#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
+
+/* For checksumming , the sum of all words in the EEPROM should equal 0xBABA */
+#define EEPROM_SUM 0xBABA
+#define NODE_ADDRESS_SIZE 6
+
+/* Statistics counters collected by the MAC */
+struct stats_msg_block {
+ /* rx */
+ u32 rx_ok; /* The number of good packet received. */
+ u32 rx_bcast; /* The number of good broadcast packet received. */
+ u32 rx_mcast; /* The number of good multicast packet received. */
+ u32 rx_pause; /* The number of Pause packet received. */
+ u32 rx_ctrl; /* The number of Control packet received other than Pause frame. */
+ u32 rx_fcs_err; /* The number of packets with bad FCS. */
+ u32 rx_len_err; /* The number of packets with mismatch of length field and actual size. */
+ u32 rx_byte_cnt; /* The number of bytes of good packet received. FCS is NOT included. */
+ u32 rx_runt; /* The number of packets received that are less than 64 byte long and with good FCS. */
+ u32 rx_frag; /* The number of packets received that are less than 64 byte long and with bad FCS. */
+ u32 rx_sz_64; /* The number of good and bad packets received that are 64 byte long. */
+ u32 rx_sz_65_127; /* The number of good and bad packets received that are between 65 and 127-byte long. */
+ u32 rx_sz_128_255; /* The number of good and bad packets received that are between 128 and 255-byte long. */
+ u32 rx_sz_256_511; /* The number of good and bad packets received that are between 256 and 511-byte long. */
+ u32 rx_sz_512_1023; /* The number of good and bad packets received that are between 512 and 1023-byte long. */
+ u32 rx_sz_1024_1518; /* The number of good and bad packets received that are between 1024 and 1518-byte long. */
+ u32 rx_sz_1519_max; /* The number of good and bad packets received that are between 1519-byte and MTU. */
+ u32 rx_sz_ov; /* The number of good and bad packets received that are more than MTU size šC truncated by Selene. */
+ u32 rx_rxf_ov; /* The number of frame dropped due to occurrence of RX FIFO overflow. */
+ u32 rx_rrd_ov; /* The number of frame dropped due to occurrence of RRD overflow. */
+ u32 rx_align_err; /* Alignment Error */
+ u32 rx_bcast_byte_cnt; /* The byte count of broadcast packet received, excluding FCS. */
+ u32 rx_mcast_byte_cnt; /* The byte count of multicast packet received, excluding FCS. */
+ u32 rx_err_addr; /* The number of packets dropped due to address filtering. */
+
+ /* tx */
+ u32 tx_ok; /* The number of good packet transmitted. */
+ u32 tx_bcast; /* The number of good broadcast packet transmitted. */
+ u32 tx_mcast; /* The number of good multicast packet transmitted. */
+ u32 tx_pause; /* The number of Pause packet transmitted. */
+ u32 tx_exc_defer; /* The number of packets transmitted with excessive deferral. */
+ u32 tx_ctrl; /* The number of packets transmitted is a control frame, excluding Pause frame. */
+ u32 tx_defer; /* The number of packets transmitted that is deferred. */
+ u32 tx_byte_cnt; /* The number of bytes of data transmitted. FCS is NOT included. */
+ u32 tx_sz_64; /* The number of good and bad packets transmitted that are 64 byte long. */
+ u32 tx_sz_65_127; /* The number of good and bad packets transmitted that are between 65 and 127-byte long. */
+ u32 tx_sz_128_255; /* The number of good and bad packets transmitted that are between 128 and 255-byte long. */
+ u32 tx_sz_256_511; /* The number of good and bad packets transmitted that are between 256 and 511-byte long. */
+ u32 tx_sz_512_1023; /* The number of good and bad packets transmitted that are between 512 and 1023-byte long. */
+ u32 tx_sz_1024_1518; /* The number of good and bad packets transmitted that are between 1024 and 1518-byte long. */
+ u32 tx_sz_1519_max; /* The number of good and bad packets transmitted that are between 1519-byte and MTU. */
+ u32 tx_1_col; /* The number of packets subsequently transmitted successfully with a single prior collision. */
+ u32 tx_2_col; /* The number of packets subsequently transmitted successfully with multiple prior collisions. */
+ u32 tx_late_col; /* The number of packets transmitted with late collisions. */
+ u32 tx_abort_col; /* The number of transmit packets aborted due to excessive collisions. */
+ u32 tx_underrun; /* The number of transmit packets aborted due to transmit FIFO underrun, or TRD FIFO underrun */
+ u32 tx_rd_eop; /* The number of times that read beyond the EOP into the next frame area when TRD was not written timely */
+ u32 tx_len_err; /* The number of transmit packets with length field does NOT match the actual frame size. */
+ u32 tx_trunc; /* The number of transmit packets truncated due to size exceeding MTU. */
+ u32 tx_bcast_byte; /* The byte count of broadcast packet transmitted, excluding FCS. */
+ u32 tx_mcast_byte; /* The byte count of multicast packet transmitted, excluding FCS. */
+ u32 smb_updated; /* 1: SMB Updated. This is used by software as the indication of the statistics update.
+ * Software should clear this bit as soon as retrieving the statistics information. */
+} _ATL1_ATTRIB_PACK_;
+
+/* Coalescing Message Block */
+struct coals_msg_block {
+ u32 int_stats; /* interrupt status */
+ u16 rrd_prod_idx; /* TRD Producer Index. */
+ u16 rfd_cons_idx; /* RFD Consumer Index. */
+ u16 update; /* Selene sets this bit every time it DMA the CMB to host memory.
+ * Software supposes to clear this bit when CMB information is processed. */
+ u16 tpd_cons_idx; /* TPD Consumer Index. */
+} _ATL1_ATTRIB_PACK_;
+
+/* RRD descriptor */
+struct rx_return_desc {
+ u8 num_buf; /* Number of RFD buffers used by the received packet */
+ u8 resved;
+ u16 buf_indx; /* RFD Index of the first buffer */
+ union {
+ u32 valid;
+ struct {
+ u16 rx_chksum;
+ u16 pkt_size;
+ } xsum_sz;
+ } xsz;
+
+ u16 pkt_flg; /* Packet flags */
+ u16 err_flg; /* Error flags */
+ u16 resved2;
+ u16 vlan_tag; /* VLAN TAG */
+} _ATL1_ATTRIB_PACK_;
+
+#define PACKET_FLAG_ETH_TYPE 0x0080
+#define PACKET_FLAG_VLAN_INS 0x0100
+#define PACKET_FLAG_ERR 0x0200
+#define PACKET_FLAG_IPV4 0x0400
+#define PACKET_FLAG_UDP 0x0800
+#define PACKET_FLAG_TCP 0x1000
+#define PACKET_FLAG_BCAST 0x2000
+#define PACKET_FLAG_MCAST 0x4000
+#define PACKET_FLAG_PAUSE 0x8000
+
+#define ERR_FLAG_CRC 0x0001
+#define ERR_FLAG_CODE 0x0002
+#define ERR_FLAG_DRIBBLE 0x0004
+#define ERR_FLAG_RUNT 0x0008
+#define ERR_FLAG_OV 0x0010
+#define ERR_FLAG_TRUNC 0x0020
+#define ERR_FLAG_IP_CHKSUM 0x0040
+#define ERR_FLAG_L4_CHKSUM 0x0080
+#define ERR_FLAG_LEN 0x0100
+#define ERR_FLAG_DES_ADDR 0x0200
+
+/* RFD descriptor */
+struct rx_free_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 buf_len; /* Size of the receive buffer in host memory, in byte */
+ u16 coalese; /* Update consumer index to host after the reception of this frame */
+} _ATL1_ATTRIB_PACK_;
+
+/* TPD descriptor */
+struct tso_param {
+ unsigned buf_len:14;
+ unsigned dma_int:1;
+ unsigned pkt_int:1;
+ u16 valan_tag;
+ unsigned eop:1;
+ /* command */
+ unsigned coalese:1;
+ unsigned ins_vlag:1;
+ unsigned custom_chksum:1;
+ unsigned segment:1;
+ unsigned ip_chksum:1;
+ unsigned tcp_chksum:1;
+ unsigned udp_chksum:1;
+ /* packet state */
+ unsigned vlan_tagged:1;
+ unsigned eth_type:1;
+ unsigned iphl:4;
+ unsigned tcp_hdrlen:4;
+ unsigned hdr_flg:1;
+ unsigned mss:13;
+} _ATL1_ATTRIB_PACK_;
+
+struct csum_param {
+ unsigned buf_len:14;
+ unsigned dma_int:1;
+ unsigned pkt_int:1;
+ u16 valan_tag;
+ unsigned eop:1;
+ /* command */
+ unsigned coalese:1;
+ unsigned ins_vlag:1;
+ unsigned custom_chksum:1;
+ unsigned segment:1;
+ unsigned ip_chksum:1;
+ unsigned tcp_chksum:1;
+ unsigned udp_chksum:1;
+ /* packet state */
+ unsigned vlan_tagged:1;
+ unsigned eth_type:1;
+ unsigned iphl:4;
+ unsigned:2;
+ unsigned payload_offset:8;
+ unsigned xsum_offset:8;
+} _ATL1_ATTRIB_PACK_;
+
+union tpd_descr {
+ u64 data;
+ struct csum_param csum;
+ struct tso_param tso;
+} _ATL1_ATTRIB_PACK_;
+
+struct tx_packet_desc {
+ __le64 buffer_addr;
+ union tpd_descr desc;
+} _ATL1_ATTRIB_PACK_;
+
+/* DMA Order Settings */
+enum atl1_dma_order {
+ atl1_dma_ord_in = 1,
+ atl1_dma_ord_enh = 2,
+ atl1_dma_ord_out = 4
+};
+
+enum atl1_dma_rcb {
+ atl1_rcb_64 = 0,
+ atl1_rcb_128 = 1
+};
+
+enum atl1_dma_req_block {
+ atl1_dma_req_128 = 0,
+ atl1_dma_req_256 = 1,
+ atl1_dma_req_512 = 2,
+ atl1_dam_req_1024 = 3,
+ atl1_dam_req_2048 = 4,
+ atl1_dma_req_4096 = 5
+};
+
+/* UNUSED - jkc 20061118
+enum atl1_speed_duplex_type {
+ atl1_10_half = 0,
+ atl1_10_full = 1,
+ atl1_100_half = 2,
+ atl1_100_full = 3
+};
+*/
+
+struct atl1_spi_flash_dev {
+ const char *manu_name; /* manufacturer id */
+ /* op-code */
+ u8 cmd_wrsr;
+ u8 cmd_read;
+ u8 cmd_program;
+ u8 cmd_wren;
+ u8 cmd_wrdi;
+ u8 cmd_rdsr;
+ u8 cmd_rdid;
+ u8 cmd_sector_erase;
+ u8 cmd_chip_erase;
+};
+
+/* Structure containing variables used by the shared code */
+struct atl1_hw {
+ u8 __iomem *hw_addr;
+ void *back;
+
+ enum atl1_dma_order dma_ord;
+ enum atl1_dma_rcb rcb_value;
+ enum atl1_dma_req_block dmar_block;
+ enum atl1_dma_req_block dmaw_block;
+
+ u8 preamble_len;
+ u8 max_retry; /* Retransmission maximum , afterwards the packet will be discarded. */
+ u8 jam_ipg; /* IPG to start JAM for collision based flow control in half-duplex mode. In unit of 8-bit time. */
+ u8 ipgt; /* Desired back to back inter-packet gap. The default is 96-bit time. */
+ u8 min_ifg; /* Minimum number of IFG to enforce in between RX frames. Frame gap below such IFP is dropped. */
+ u8 ipgr1; /* 64bit Carrier-Sense window */
+ u8 ipgr2; /* 96-bit IPG window */
+
+ u8 tpd_burst; /* Number of TPD to prefetch in a cache-aligned burst. Each TPD is 16-byte in length. */
+ u8 rfd_burst; /* Number of RFD to prefetch in a cache-aligned burst. Each RFD is 12-byte in length. */
+ u8 rfd_fetch_gap;
+ u8 rrd_burst; /* Threshold of number of RRDs can be retired in a burst. Each RRD is 16-byte in length. */
+ u8 tpd_fetch_th;
+ u8 tpd_fetch_gap;
+ u16 tx_jumbo_task_th;
+ u16 txf_burst; /* Number of data byte to read in a cache-aligned burst. Each SRAM entry is 8-byte in length. */
+ u16 rx_jumbo_th; /* Jumbo packet size for non-VLAN packet. VLAN packet should add 4-byte */
+ u16 rx_jumbo_lkah;
+ u16 rrd_ret_timer; /* RRD retirement timer. Decrement by 1 after every 512ns passes. */
+ u16 lcol; /* Collision Window */
+
+ u16 cmb_tpd;
+ u16 cmb_rrd;
+ u16 cmb_rx_timer;
+ u16 cmb_tx_timer;
+ u32 smb_timer;
+ u16 media_type;
+ u16 autoneg_advertised;
+ u16 pci_cmd_word;
+
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg;
+
+ u32 mem_rang;
+ u32 txcw;
+ u32 max_frame_size;
+ u32 min_frame_size;
+ u32 mc_filter_type;
+ u32 num_mc_addrs;
+ u32 collision_delta;
+ u32 tx_packet_delta;
+ u16 phy_spd_default;
+
+ u16 dev_rev;
+ u16 device_id;
+ u16 vendor_id;
+ u16 subsystem_id;
+ u16 subsystem_vendor_id;
+ u8 revision_id;
+
+ /* spi flash */
+ u8 flash_vendor;
+
+ u8 dma_fairness;
+ u8 mac_addr[NODE_ADDRESS_SIZE];
+ u8 perm_mac_addr[NODE_ADDRESS_SIZE];
+
+ /* bool phy_preamble_sup; */
+ bool phy_configured;
+};
+
+/* formerly ATL1_WRITE_REG */
+static inline void atl1_write32(const struct atl1_hw *hw, int reg, u32 val)
+{
+ writel(val, hw->hw_addr + reg);
+}
+
+/* formerly ATL1_READ_REG */
+static inline u32 atl1_read32(const struct atl1_hw *hw, int reg)
+{
+ return readl(hw->hw_addr + reg);
+}
+
+/* formerly ATL1_WRITE_REGB */
+static inline void atl1_write8(const struct atl1_hw *hw, int reg, u32 val)
+{
+ writeb(val, hw->hw_addr + reg);
+}
+
+/* formerly ATL1_READ_REGB */
+static inline u8 atl1_read8(const struct atl1_hw *hw, int reg)
+{
+ return readb(hw->hw_addr + reg);
+}
+
+/* formerly ATL1_WRITE_REGW */
+static inline void atl1_write16(const struct atl1_hw *hw, int reg, u32 val)
+{
+ writew(val, hw->hw_addr + reg);
+}
+
+/* formerly ATL1_READ_REGW */
+static inline u16 atl1_read16(const struct atl1_hw *hw, int reg)
+{
+ return readw(hw->hw_addr + reg);
+}
+
+/* formerly ATL1_WRITE_REG_ARRAY */
+static inline void atl1_write32_array(const struct atl1_hw *hw, int reg, int offset, u32 val)
+{
+ writel(val, (hw->hw_addr + reg) + (offset << 2));
+}
+
+/* formerly ATL1_READ_REG_ARRAY */
+static inline u32 atl1_read32_array(const struct atl1_hw *hw, int reg, int offset)
+{
+ return readl((hw->hw_addr + reg) + (offset << 2));
+}
+
+#endif /* _ATL1_HW_H_ */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
