2006/11/9, Jiri Slaby <[email protected]>:
Jano: please, do not remove Cc people, when replying (i.e. reply to all)
Oops, apologise, I'm getting used to a different mail client
interface. I'll try to do my best to follow the etiquette.
Phillip Susi wrote:
> Ubuntu uses an initramfs, so unless he has rebuilt his kernel to get
> around that, he should still be using one.
I've compiled it into the kernel, but it doesn't work.
> OP, please check dmesg for any new errors after you attempt to mount
> something on hdb. Also what is the output of a mount command with no
> options?
Mount haven't changed. And here's my dmesg acquired after the last
compilation. It's a diff from the previous version I posted, which can
be found here: http://lkml.org/lkml/2006/11/08/322
--- 2.6.18.1 2006-11-08 22:07:53.000000000 +0100
+++ 2.6.18.1b 2006-11-09 18:32:26.000000000 +0100
@@ -51,7 +51,7 @@
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 906300k/917504k available (1813k kernel code, 10728k
reserved, 571k data, 172k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
-Calibrating delay using timer specific routine.. 3682.73 BogoMIPS (lpj=7365468)
+Calibrating delay using timer specific routine.. 3682.72 BogoMIPS (lpj=7365441)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000
00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
00000000 00000000 00000000
@@ -150,31 +150,16 @@
Freeing unused kernel memory: 172k freed
input: ImExPS/2 Logitech Wheel Mouse as /class/input/input1
NET: Registered protocol family 1
-hdc: ATAPI 52X DVD-ROM drive, 256kB Cache
-Uniform CD-ROM driver Revision: 3.20
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
-usbcore: registered new driver usbfs
-usbcore: registered new driver hub
-ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 17
-PCI: VIA IRQ fixup for 0000:00:10.3, from 0 to 1
-ehci_hcd 0000:00:10.3: EHCI Host Controller
-ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
-ehci_hcd 0000:00:10.3: irq 17, io mem 0xbe000000
-ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
-usb usb1: configuration #1 chosen from 1 choice
-hub 1-0:1.0: USB hub found
-hub 1-0:1.0: 6 ports detected
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
-hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
-ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 18
+ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:0d.0 disabled
-usb 1-1: new high speed USB device using ehci_hcd and address 2
-usb 1-1: configuration #1 chosen from 1 choice
-ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
+hdc: ATAPI 52X DVD-ROM drive, 256kB Cache
+Uniform CD-ROM driver Revision: 3.20
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
@@ -185,10 +170,25 @@
VP_IDE: port 0x01f0 already claimed by ide0
VP_IDE: port 0x0170 already claimed by ide1
VP_IDE: neither IDE port enabled (BIOS)
+hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
+usbcore: registered new driver usbfs
+usbcore: registered new driver hub
+ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
+PCI: VIA IRQ fixup for 0000:00:10.3, from 0 to 2
+ehci_hcd 0000:00:10.3: EHCI Host Controller
+ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
+ehci_hcd 0000:00:10.3: irq 18, io mem 0xbe000000
+ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
+usb usb1: configuration #1 chosen from 1 choice
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 6 ports detected
NET: Registered protocol family 17
+usb 1-1: new high speed USB device using ehci_hcd and address 2
+usb 1-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if
0 alt 0 proto 2 vid 0x03F0 pid 0x2B17
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
+ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Below I've attach diff of my current .config in comparison to the one
posted over here: http://lkml.org/lkml/2006/11/09/11
--- config_old 2006-11-09 18:50:59.000000000 +0100
+++ /usr/src/linux-2.6.18.1/.config 2006-11-09 18:25:25.000000000 +0100
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.18.1
-# Thu Nov 9 00:28:54 2006
+# Thu Nov 9 18:25:25 2006
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
@@ -187,6 +187,7 @@
CONFIG_PHYSICAL_START=0x100000
CONFIG_COMPAT_VDSO=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+
#
# Power management options (ACPI, APM)
#
@@ -592,8 +593,11 @@
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
-# CONFIG_BLK_DEV_RAM is not set
-# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
@@ -607,7 +611,7 @@
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
-# CONFIG_BLK_DEV_HD_IDE is not set
+CONFIG_BLK_DEV_HD_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=m
@@ -618,7 +622,7 @@
#
# IDE chipset support/bugfixes
#
-CONFIG_IDE_GENERIC=y
+CONFIG_IDE_GENERIC=m
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
@@ -658,7 +662,7 @@
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
-# CONFIG_BLK_DEV_HD is not set
+CONFIG_BLK_DEV_HD=y
#
# SCSI device support
@@ -758,6 +762,7 @@
CONFIG_SCSI_DC390T=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m
+
#
# Multi-device support (RAID and LVM)
#
@@ -882,6 +887,7 @@
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+
#
# Token Ring devices
#
I hope this will be helpful. Thank you for your feedback.
Best regards,
Jano
--
Mail jano at stepien com pl
Jabber jano at jabber aster pl
GG 1894343
Web stepien.com.pl
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
