Re: UDP question.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 9/16/06, xixi lii <[email protected]> wrote:
2006/9/16, David Schwartz <[email protected]>:
>
> > My two adapters has two different IP address, and I bind one IP
> > on one socket,
> > do you mean that I alloc two socket and bind different IP is not
> > helpful?
>
>        Correct. You are still sending all the packets *to* the same place.
>
> > In fact, all the packet sent from two socket is go out by one
> > network adapter?
>
>        Yes, of course. Why would the kernel send traffic to a destination out an
> interface that doesn't go to that destination?
>
>        Suppose you have two interfaces, 1.2.3.4/8 and 10.2.3.4/8, if you are
> sending a packet *to* 1.2.4.5, it will go out the first interface. This
> applies whether the source address is 1.2.3.4 or 10.2.3.4.
>
>        By default, the kernel routes traffic based on where it is going, not which
> interface address it came from.
>
>        DS
>

Let me explain my network environment, My program is running on a two
adapters machine, whose IP is 192.168.0.1/8 and 192.168.0.2/8, then,
my destination is two machine, whose IP is 192.168.0.3/8 and
192.168.0.4/8. I use four 100M exchange and a 1000M exchange cennected
them to ensure the choke point is not at network  equipment.

when I use two socket without bonding, one socket is bind
192.168.0.1/8 and sendto 192.168.0.3/8, the other is bind
192.168.0.2/8 and sendto 192.168.0.4/8, but, as you see, I get a
result that the speed of send by two adapters is equal to the only one
adapter's.

why dont you try a different subnet for the other adapter & its dest.
something like 192.168.1.2/8 & dest 192.168.1.4/8 ?

Because whenever a packet needs to be sent out, the routing table is
consulted. (check out the output of route / netstat -nr ) So for a
given subnet, only the first interface encountered in the table is
used. Remaining interfaces are used, only if the first fails fails.


yesterday. I got an uncertain idea, is the problem that IP layer is
separate with Eth layer ? when I bind src IP, it just do helpful to IP
layer, not real bind the adapter? when I send, the real ethreal
adapter is select by IP route? If the two interface can go
destinnation both, IP layer will choose the frist, not use both? Am I
right?

yes, that is what the routing table is about.

If so, when I use bonding, the adapter's physical address is the frist
one, Do this means that all of the packet come to my machine will go
through in the frist one adapter?

No. It just means that the MAC address of the 2 nd card is overridden
with the 1st one's MAC. i.e. all packets sent through 2nd NIC will
bear the 1st MAC. The reason this is done is not to confuse network
equipment which sends out ARP messages etc to resolve IP addresses.
(Switches should be intelligent here, else you will have issues with
recving packets on both interfaces).


Thx all.
Best Regard.

xixi

Bhanu.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux