Hello.
Rework hpt3xx_ratemask() and hpt3xx_ratefilter() so that the former
returns the max. mode computed at the load time and doesn't have to do bad
Ultra33 drive list lookups anymore; remove the duplicate code from the latter
function. Move the quirky drive list lookup into hpt3xx_quirkproc() where it
should have been from the start...
Disable UltraATA/100 for HPT370 by default as the 33 MHz ATA clock being
used does not allow for it, and this *greatly* increases the transfer speed.
Save some space by using byte-wide fields in struct hpt_info; switch to
reading the 8-bit PCI revision ID reg. only, not the whole 32-bit reg.
Start incrementing the driver version number with each patch (should have
been done from the first one posted).
MBR, Sergei
Signed-off-by: Sergei Shtylyov <[email protected]>
Index: linus/drivers/ide/pci/hpt366.c
===================================================================
--- linus.orig/drivers/ide/pci/hpt366.c
+++ linus/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
+ * linux/drivers/ide/pci/hpt366.c Version 0.43 May 17, 2006
*
* Copyright (C) 1999-2003 Andre Hedrick <[email protected]>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
@@ -62,8 +62,8 @@
* be done on 66 MHz PCI bus
* - avoid calibrating PLL twice as the second time results in a wrong PCI
* frequency and thus in the wrong timings for the secondary channel
- * - disable UltraATA/133 for HPT372 by default (50 MHz DPLL clock do not
- * allow for this speed anyway)
+ * - disable UltraATA/133 for HPT372 and UltraATA/100 for HPT370 by default
+ * as the ATA clock being used does not allow for this speed anyway
* - add support for HPT302N and HPT371N clocking (the same as for HPT372N)
* - HPT371/N are single channel chips, so avoid touching the primary channel
* which exists only virtually (there's no pins for it)
@@ -76,6 +76,7 @@
* and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
* - pass to init_chipset() handlers a copy of the IDE PCI device structure as
* they tamper with its fields
+ * - optimize the rate masking/filtering and the drive list lookup code
* <[email protected]>
*
*/
@@ -337,7 +338,7 @@ static u32 sixty_six_base_hpt37x[] = {
#define HPT371_ALLOW_ATA133_6 0
#define HPT302_ALLOW_ATA133_6 0
#define HPT372_ALLOW_ATA133_6 0
-#define HPT370_ALLOW_ATA100_5 1
+#define HPT370_ALLOW_ATA100_5 0
#define HPT366_ALLOW_ATA66_4 1
#define HPT366_ALLOW_ATA66_3 1
#define HPT366_MAX_DEVS 8
@@ -355,8 +356,8 @@ static u32 sixty_six_base_hpt37x[] = {
struct hpt_info
{
u8 max_mode; /* Speeds allowed */
- int revision; /* Chipset revision */
- int flags; /* Chipset properties */
+ u8 revision; /* Chipset revision */
+ u8 flags; /* Chipset properties */
#define PLL_MODE 1
#define IS_3xxN 2
#define PCI_66MHZ 4
@@ -365,61 +366,50 @@ struct hpt_info
};
/*
- * This wants fixing so that we do everything not by classrev
+ * This wants fixing so that we do everything not by revision
* (which breaks on the newest chips) but by creating an
* enumeration of chip variants and using that
*/
-static __devinit u32 hpt_revision (struct pci_dev *dev)
+static __devinit u8 hpt_revision(struct pci_dev *dev)
{
- u32 class_rev;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
+ u8 rev = 0;
+
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
switch(dev->device) {
/* Remap new 372N onto 372 */
case PCI_DEVICE_ID_TTI_HPT372N:
- class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
+ rev = PCI_DEVICE_ID_TTI_HPT372; break;
case PCI_DEVICE_ID_TTI_HPT374:
- class_rev = PCI_DEVICE_ID_TTI_HPT374; break;
+ rev = PCI_DEVICE_ID_TTI_HPT374; break;
case PCI_DEVICE_ID_TTI_HPT371:
- class_rev = PCI_DEVICE_ID_TTI_HPT371; break;
+ rev = PCI_DEVICE_ID_TTI_HPT371; break;
case PCI_DEVICE_ID_TTI_HPT302:
- class_rev = PCI_DEVICE_ID_TTI_HPT302; break;
+ rev = PCI_DEVICE_ID_TTI_HPT302; break;
case PCI_DEVICE_ID_TTI_HPT372:
- class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
+ rev = PCI_DEVICE_ID_TTI_HPT372; break;
default:
break;
}
- return class_rev;
+ return rev;
}
-static int check_in_drive_lists(ide_drive_t *drive, const char **list);
-
-static u8 hpt3xx_ratemask (ide_drive_t *drive)
+static int check_in_drive_list(ide_drive_t *drive, const char **list)
{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 mode = 0;
+ struct hd_driveid *id = drive->id;
- /* FIXME: TODO - move this to set info->mode once at boot */
+ while (*list)
+ if (!strcmp(*list++,id->model))
+ return 1;
+ return 0;
+}
+
+static u8 hpt3xx_ratemask(ide_drive_t *drive)
+{
+ struct hpt_info *info = ide_get_hwifdata(HWIF(drive));
+ u8 mode = info->max_mode;
- if (info->revision >= 8) { /* HPT374 */
- mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 7) { /* HPT371 */
- mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 6) { /* HPT302 */
- mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 5) { /* HPT372 */
- mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 4) { /* HPT370A */
- mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
- } else if (info->revision >= 3) { /* HPT370 */
- mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
- mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode;
- } else { /* HPT366 and HPT368 */
- mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2;
- }
if (!eighty_ninty_three(drive) && mode)
mode = min(mode, (u8)1);
return mode;
@@ -430,16 +420,15 @@ static u8 hpt3xx_ratemask (ide_drive_t *
* either PIO or UDMA modes 0,4,5
*/
-static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
+static u8 hpt3xx_ratefilter(ide_drive_t *drive, u8 speed)
{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
+ struct hpt_info *info = ide_get_hwifdata(HWIF(drive));
u8 mode = hpt3xx_ratemask(drive);
if (drive->media != ide_disk)
return min(speed, (u8)XFER_PIO_4);
- switch(mode) {
+ switch (mode) {
case 0x04:
speed = min(speed, (u8)XFER_UDMA_6);
break;
@@ -447,33 +436,34 @@ static u8 hpt3xx_ratefilter (ide_drive_t
speed = min(speed, (u8)XFER_UDMA_5);
if (info->revision >= 5)
break;
- if (check_in_drive_lists(drive, bad_ata100_5))
- speed = min(speed, (u8)XFER_UDMA_4);
- break;
+ if (!check_in_drive_list(drive, bad_ata100_5))
+ goto check_bad_ata33;
+ /* fall thru */
case 0x02:
speed = min(speed, (u8)XFER_UDMA_4);
/*
* CHECK ME, Does this need to be set to 5 ??
*/
if (info->revision >= 3)
- break;
- if ((check_in_drive_lists(drive, bad_ata66_4)) ||
- (!(HPT366_ALLOW_ATA66_4)))
- speed = min(speed, (u8)XFER_UDMA_3);
- if ((check_in_drive_lists(drive, bad_ata66_3)) ||
- (!(HPT366_ALLOW_ATA66_3)))
- speed = min(speed, (u8)XFER_UDMA_2);
- break;
+ goto check_bad_ata33;
+ if (HPT366_ALLOW_ATA66_4 &&
+ !check_in_drive_list(drive, bad_ata66_4))
+ goto check_bad_ata33;
+
+ speed = min(speed, (u8)XFER_UDMA_3);
+ if (HPT366_ALLOW_ATA66_3 &&
+ !check_in_drive_list(drive, bad_ata66_3))
+ goto check_bad_ata33;
+ /* fall thru */
case 0x01:
speed = min(speed, (u8)XFER_UDMA_2);
- /*
- * CHECK ME, Does this need to be set to 5 ??
- */
- if (info->revision >= 3)
+
+ check_bad_ata33:
+ if (info->revision >= 4)
break;
- if (check_in_drive_lists(drive, bad_ata33))
- speed = min(speed, (u8)XFER_MW_DMA_2);
- break;
+ if (!check_in_drive_list(drive, bad_ata33))
+ break;
+ /* fall thru */
case 0x00:
default:
speed = min(speed, (u8)XFER_MW_DMA_2);
@@ -482,22 +472,6 @@ static u8 hpt3xx_ratefilter (ide_drive_t
return speed;
}
-static int check_in_drive_lists (ide_drive_t *drive, const char **list)
-{
- struct hd_driveid *id = drive->id;
-
- if (quirk_drives == list) {
- while (*list)
- if (strstr(id->model, *list++))
- return 1;
- } else {
- while (*list)
- if (!strcmp(*list++,id->model))
- return 1;
- }
- return 0;
-}
-
static u32 pci_bus_clock_list(u8 speed, u32 *chipset_table)
{
int i;
@@ -672,9 +646,15 @@ static int config_chipset_for_dma (ide_d
return ide_dma_enable(drive);
}
-static int hpt3xx_quirkproc (ide_drive_t *drive)
+static int hpt3xx_quirkproc(ide_drive_t *drive)
{
- return ((int) check_in_drive_lists(drive, quirk_drives));
+ struct hd_driveid *id = drive->id;
+ const char **list = quirk_drives;
+
+ while (*list)
+ if (strstr(id->model, *list++))
+ return 1;
+ return 0;
}
static void hpt3xx_intrproc (ide_drive_t *drive)
@@ -1382,7 +1362,7 @@ static void __devinit init_iops_hpt366(i
struct hpt_info *info = kzalloc(sizeof(struct hpt_info), GFP_KERNEL);
struct pci_dev *dev = hwif->pci_dev;
u16 did = dev->device;
- u8 rid = 0;
+ u8 mode, rid = 0;
if(info == NULL) {
printk(KERN_WARNING "hpt366: out of memory.\n");
@@ -1396,7 +1376,7 @@ static void __devinit init_iops_hpt366(i
return;
}
- pci_read_config_byte(dev, PCI_CLASS_REVISION, &rid);
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rid);
if (( did == PCI_DEVICE_ID_TTI_HPT366 && rid == 6) ||
((did == PCI_DEVICE_ID_TTI_HPT372 ||
@@ -1405,9 +1385,22 @@ static void __devinit init_iops_hpt366(i
did == PCI_DEVICE_ID_TTI_HPT372N)
info->flags |= IS_3xxN;
- info->revision = hpt_revision(dev);
+ rid = info->revision = hpt_revision(dev);
+ if (rid >= 8) /* HPT374 */
+ mode = HPT374_ALLOW_ATA133_6 ? 4 : 3;
+ else if (rid >= 7) /* HPT371 and HPT371N */
+ mode = HPT371_ALLOW_ATA133_6 ? 4 : 3;
+ else if (rid >= 6) /* HPT302 and HPT302N */
+ mode = HPT302_ALLOW_ATA133_6 ? 4 : 3;
+ else if (rid >= 5) /* HPT372, HPT372A, and HPT372N */
+ mode = HPT372_ALLOW_ATA133_6 ? 4 : 3;
+ else if (rid >= 3) /* HPT370 and HPT370A */
+ mode = HPT370_ALLOW_ATA100_5 ? 3 : 2;
+ else /* HPT366 and HPT368 */
+ mode = (HPT366_ALLOW_ATA66_4 || HPT366_ALLOW_ATA66_3) ? 2 : 1;
+ info->max_mode = mode;
- if (info->revision >= 3)
+ if (rid >= 3)
hpt37x_clocking(hwif);
else
hpt366_clocking(hwif);
@@ -1462,8 +1455,7 @@ static int __devinit init_setup_hpt371(s
static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d)
{
struct pci_dev *findev = NULL;
- u8 pin1 = 0, pin2 = 0;
- unsigned int class_rev;
+ u8 rev = 0, pin1 = 0, pin2 = 0;
char *chipset_names[] = {"HPT366", "HPT366", "HPT368",
"HPT370", "HPT370A", "HPT372",
"HPT372N" };
@@ -1471,16 +1463,15 @@ static int __devinit init_setup_hpt366(s
if (PCI_FUNC(dev->devfn) & 1)
return -ENODEV;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
if(dev->device == PCI_DEVICE_ID_TTI_HPT372N)
- class_rev = 6;
+ rev = 6;
- if(class_rev <= 6)
- d->name = chipset_names[class_rev];
+ if(rev <= 6)
+ d->name = chipset_names[rev];
- switch(class_rev) {
+ switch(rev) {
case 6:
case 5:
case 4:
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
