Hello,
[1.] One line summary of the problem:
saa7134 and tuner modules / Problem with Pinnacle MediaCenter 300i
[2.] Full description of the problem/report:
After starting the computer, I do a modprobe saa7134.
These are the options from /etc/modprobe.conf:
options tuner no_autodetect=33
options saa7134 card=50 tuner=33
(Autodetection for card= works, but I set it anyways. Tuner
autodetection seems to be broken)
dmesg output:
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKA] -> GSI 19 (level,
low) -> IRQ 17
saa7134[0]: found at 0000:02:0a.0, rev: 1, irq: 17, latency: 64, mmio:
0xfeaff800
saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL
[card=50,insmod option]
saa7134[0]: board init: gpio is c806000
saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 27 36 95 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: 00 30 8d 18 cc d8 ff ff f4 b8 ff ff ff ff ff ff
tuner 2-0043: chip found @ 0x86 (saa7134[0])
tuner 2-0043: microtune: companycode=e0e0 part=e0 rev=e0
tuner 2-0043: microtune unknown found, not (yet?) supported, sorry :-/
saa7134[0]/irq[10,4297703459]: r=0x20 s=0x00 PE
saa7134[0]/irq: looping -- clearing PE (parity error!) enable bit
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
As you can see, the tuner does not work. I do a rmmod tuner and a rmmod
saa7134 and do a modprobe saa7134 again:
dmesg output:
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKA] -> GSI 19 (level,
low) -> IRQ 17
saa7134[0]: found at 0000:02:0a.0, rev: 1, irq: 17, latency: 64, mmio:
0xfeaff800
saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL
[card=50,insmod option]
saa7134[0]: board init: gpio is c806000
tda9887 2-0043: chip found @ 0x86 (saa7134[0])
saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 27 36 95 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: 00 30 8d 18 cc d8 ff ff f4 b8 ff ff ff ff ff ff
tuner 2-0060: chip found @ 0xc0 (saa7134[0])
tuner 2-0060: microtune: companycode=3cbf part=42 rev=83
tuner 2-0060: microtune MT2050 found, OK
saa7134[0]/irq[10,4298210983]: r=0x20 s=0x00 PE
saa7134[0]/irq: looping -- clearing PE (parity error!) enable bit
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
After that the card is working.
So something goes wrong with detection. One funny thing: If repeating
steps from above, the rev= line changes: See:
tuner 2-0060: microtune: companycode=3cbf part=42 rev=88
[3.] Keywords (i.e., modules, networking, kernel):
saa7134; Multimedia
[4.] Kernel version (from /proc/version):
Linux version 2.6.15-suspend2-r5 (root@amd64) (gcc-Version 4.0.2 (Gentoo
4.0.2-r3, pie-8.7.8)) #5 PREEMPT Wed Feb 8 17:59:21 CET 2006
Same with vanilla-sources (2.6.15.3) and 2.6.16_rc2-git
[5.] Most recent kernel version which did not have the bug:
I am not sure, but I think it was version 2.6.14.x
[6.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
No Oopses
[7.] A small shell script or example program which triggers the
problem (if possible)
Only the modprobe/rmmod stuff from above
[8.] Environment
Gentoo Base System version 1.12.0_pre15
Portage 2.1_pre4-r1 (default-linux/amd64/2005.1, gcc-4.0.2,
glibc-2.3.6-r2, 2.6.15-suspend2-r5 x86_64)
=================================================================
System uname: 2.6.15-suspend2-r5 x86_64 AMD Athlon(tm) 64 Processor 3200+
ccache version 2.4 [enabled]
dev-lang/python: 2.4.2-r1
sys-apps/sandbox: 1.2.17
sys-devel/autoconf: 2.13, 2.59-r7
sys-devel/automake: 1.4_p6, 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6-r1
sys-devel/binutils: 2.16.1-r1
sys-devel/libtool: 1.5.22
virtual/os-headers: 2.6.11-r3
ACCEPT_KEYWORDS="amd64 ~amd64"
ACCEPT_LICENSE=""
ALSA_CARDS="intel8x0 emu10k1"
ANT_HOME="/usr/share/ant-core"
ARCH="amd64"
AUTOCLEAN="yes"
BASH_ENV="/etc/spork/is/not/valid/profile.env"
CBUILD="x86_64-pc-linux-gnu"
CCACHE_SIZE="5G"
CDEFINE_amd64="__x86_64__"
CDEFINE_x86="__i386__"
CFLAGS="-O2 -march=athlon64 -pipe"
CFLAGS_x86="-m32 -L/emul/linux/x86/lib -L/emul/linux/x86/usr/lib"
CHOST="x86_64-pc-linux-gnu"
CHOST_amd64="x86_64-pc-linux-gnu"
CHOST_x86="i686-pc-linux-gnu"
CLASSPATH="."
CLEAN_DELAY="5"
CONFIG_PROTECT="/etc /usr/kde/2/share/config /usr/kde/3/share/config
/usr/share/X11/xkb /usr/share/config /var/bind /var/qmail/control"
CONFIG_PROTECT_MASK="/etc/gconf /etc/splash /etc/terminfo
/etc/texmf/web2c /etc/env.d"
CVS_RSH="ssh"
CXXFLAGS="-O2 -march=athlon64 -pipe"
DCCC_PATH="/usr/lib/distcc/bin"
DEFAULT_ABI="amd64"
DISPLAY=":0.0"
DISTCC_LOG=""
DISTCC_VERBOSE="0"
DISTDIR="/usr/portage/distfiles"
EDITOR="/usr/bin/vim"
ELIBC="glibc"
EMERGE_WARNING_DELAY="10"
FEATURES="autoconfig ccache digest distlocks prelink sandbox sfperms strict"
FETCHCOMMAND="/usr/bin/wget -t 5 --passive-ftp --no-check-certificate
${URI} -P ${DISTDIR}"
FLTK_DOCDIR="/usr/share/doc/fltk-1.1.7/html"
FRITZCAPI_CARDS="fcusb2"
GCC_SPECS=""
GDK_USE_XFT="1"
GDM_LANG="de_DE.utf8"
GENTOO_MIRRORS="http://ftp-stud.fht-esslingen.de/pub/Mirrors/gentoo/
ftp://gentoo.inode.at/source/ ftp://ftp.easynet.nl/mirror/gentoo/
ftp://sunsite.informatik.rwth-aachen.de/pub/Linux/gentoo";
GUILE_LOAD_PATH="/usr/share/guile/1.6"
G_BROKEN_FILENAMES="1"
HISTCONTROL="ignoredups:erasedups"
HOME="/root"
HOSTNAME="amd64"
INFOPATH="/usr/share/info:/usr/share/binutils-data/x86_64-pc-linux-gnu/2.16.1/info:/usr/share/gcc-data/x86_64-pc-linux-gnu/4.0.2/info"
INPUT_DEVICES="evdev keyboard mouse "
JAVAC="/opt/blackdown-jdk-1.4.2.03/bin/javac"
JAVA_HOME="/opt/blackdown-jdk-1.4.2.03"
JDK_HOME="/opt/blackdown-jdk-1.4.2.03"
KERNEL="linux"
LADSPA_PATH="/usr/lib64/ladspa"
LANG="de_DE.utf8"
LC_ALL="de_DE.utf8"
LDFLAGS_x86="-m elf_i386 -L/emul/linux/x86/lib -L/emul/linux/x86/usr/lib"
LESS="-R -M --shift 5"
LESSCHARSET="utf-8"
LESSOPEN="|lesspipe.sh %s"
LIBDIR_amd64="lib64"
LIBDIR_x86="lib32"
LINGUAS="de"
LOGNAME="root"
LS_COLORS="no=00:fi=00:di=01;34:ln=01;36:pi=40;33:so=01;35:do=01;35:bd=40;33;01:cd=40;33;01:or=01;05;37;41:mi=01;05;37;41:su=37;41:sg=30;43:tw=30;42:ow=34;42:st=37;44:ex=01;32:*.tar=01;31:*.tgz=01;31:*.arj=01;31:*.taz=01;31:*.lzh=01;31:*.zip=01;31:*.z=01;31:*.Z=01;31:*.gz=01;31:*.bz2=01;31:*.bz=01;31:*.tbz2=01;31:*.tz=01;31:*.deb=01;31:*.rpm=01;31:*.jar=01;31:*.rar=01;31:*.ace=01;31:*.zoo=01;31:*.cpio=01;31:*.7z=01;31:*.rz=01;31:*.jpg=01;35:*.jpeg=01;35:*.gif=01;35:*.bmp=01;35:*.pbm=01;35:*.pgm=01;35:*.ppm=01;35:*.tga=01;35:*.xbm=01;35:*.xpm=01;35:*.tif=01;35:*.tiff=01;35:*.png=01;35:*.mng=01;35:*.pcx=01;35:*.mov=01;35:*.mpg=01;35:*.mpeg=01;35:*.m2v=01;35:*.mkv=01;35:*.ogm=01;35:*.mp4=01;35:*.m4v=01;35:*.mp4v=01;35:*.qt=01;35:*.wmv=01;35:*.asf=01;35:*.rm=01;35:*.rmvb=01;35:*.flc=01;35:*.avi=01;35:*.fli=01;35:*.gl=01;35:*.dl=01;35:*.xcf=01;35:*.xwd=01;35:*.pdf=00;32:*.ps=00;32:*.txt=00;32:*.patch=00;32:*.diff=00;32:*.log=00;32:*.tex=00;32:*.doc=00;32:*.flac=01;35:*.mp3=01;35:*
.mpc=00;36:*.ogg=00;36:*.wav=00;36:*.mid=00;36:*.midi=00;36:*.au=00;36:*.flac=00;36:*.aac=00;36:"
MAKEOPTS="-j3"
MANPATH="/usr/local/share/man:/usr/share/man:/usr/share/binutils-data/x86_64-pc-linux-gnu/2.16.1/man:/usr/share/gcc-data/x86_64-pc-linux-gnu/4.0.2/man::/opt/blackdown-jdk-1.4.2.03/man"
MULTILIB_ABIS="x86 amd64"
MULTILIB_STRICT_DENY="64-bit.*shared object"
MULTILIB_STRICT_DIRS="/lib /usr/lib /usr/kde/*/lib /usr/qt/*/lib
/usr/X11R6/lib"
MULTILIB_STRICT_EXEMPT="(perl5|gcc|gcc-lib|eclipse-3|debug|portage)"
OPENGL_PROFILE="nvidia"
PAGER="/usr/bin/less"
PATH="/root/bin:/usr/lib/ccache/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/opt/bin:/usr/x86_64-pc-linux-gnu/gcc-bin/4.0.2:/opt/Acrobat7:/opt/blackdown-jdk-1.4.2.03/bin:/opt/blackdown-jdk-1.4.2.03/jre/bin"
PKGDIR="/usr/portage/packages"
PORTAGE_ARCHLIST="ppc s390 amd64 ppc64 m68k arm sparc sh mips ia64 alpha
ppc-macos hppa x86"
PORTAGE_BINHOST_CHUNKSIZE="3000"
PORTAGE_CALLER="emerge"
PORTAGE_ELOG_CLASSES="info warn error log"
PORTAGE_ELOG_MAILURI="root@localhost localhost"
PORTAGE_ELOG_SYSTEM="save mail"
PORTAGE_GID="250"
PORTAGE_MASTER_PID="15131"
PORTAGE_TMPDIR="/var/tmp"
PORTAGE_TMPFS="/dev/shm"
PORTDIR="/usr/portage"
PORTDIR_OVERLAY="/usr/local/overlays/portage"
PRELINK_PATH=""
PRELINK_PATH_MASK="/usr/lib/gstreamer-0.8:/lib/modules:/usr/lib64/locale:/usr/lib64/wine:/usr/lib64/valgrind:*.la:*.png:*.py:*.pl:*.pm:*.sh:*.xml:*.xslt:*.a:*.js:/usr/lib/klibc"
PWD="/root"
PYTHONDOCS="/usr/share/doc/python-docs-2.4.2/html"
PYTHONPATH="/usr/lib/portage/pym"
QTDIR="/emul/linux/x86/usr/qt/2:/emul/linux/x86/usr/qt/3"
RESUMECOMMAND="/usr/bin/wget -c -t 5 --passive-ftp
--no-check-certificate ${URI} -P ${DISTDIR}"
RPMDIR="/usr/portage/rpm"
RSYNC_RETRIES="3"
RSYNC_TIMEOUT="180"
SANE_CONFIG_DIR="/etc/sane.d"
SHELL="/bin/bash"
SHLVL="1"
SYMLINK_LIB="yes"
SYNC="rsync://rsync.europe.gentoo.org/gentoo-portage"
TERM="xterm"
USE="amd64 X X509 a52 aac aalib acl acpi acpi4linux activefilter alsa
apache2 avi bash-completion bcmath berkdb bigger-fonts bitmap-fonts
bluetooth browserplugin bzip2 bzlib cairo caps cddb cdparanoia cdr
chroot client codecs crypt cscope css ctype cups dbm dbus dga dhcp
directfb dlloader doc dri dts dvd dvdr dvdread dxr3 eds emboss encode
esd exif expat extensions faac faad fame fax faxonly fbcon fbsplash
ffmpeg firefox flac font-server foomaticdb freetype fuse gd gdbm gif
gimp gimpprint glitz glut gmp gnome gphoto2 gpm gstreamer gtk gtk2
gtkhtml guile hal hbci howl icq icu idn imagemagick imap imlib ipv6
javascript jbig jpeg jpeg2k lcd lcms ldap libcaca libclamav lirc
lm_sensors logrotate lzo lzw lzw-tiff mad maildir mailwrapper mbox mcal
md5sum mikmod mime mjpeg mng
motif mp3 mpeg mpeg4 mppe-mppc mysql nautilus ncurses network nls
no-old-linux nptl nptlonly nsplugin ntfs nvidia ogg oggvorbis opengl oss
pam password pcntl pdflib perl php pic png pnp posix postgres ppds
python quicktime readline rtc ruby samba scanner sdl session sftplogging
slang snmp sockets sox speex spell sqlite ssl subversion svg symlink
tcltk tcpd tetex theora threads tiff tokenizer truetype truetype-fonts
type1-fonts udev unicode usb userlocales vcd vim-with-x vorbis wma wmf
wxwindows xine xml2 xmms xpm xprint xrandr xscreensaver xsl xv xvid zlib
elibc_glibc fritzcapi_cards_fcusb2 input_devices_evdev
input_devices_keyboard input_devices_mouse kernel_linux linguas_de
userland_GNU video_cards_apm video_cards_v4l video_cards_nvidia
video_cards_nv"
USER="root"
USERLAND="GNU"
USE_EXPAND="DVB_CARDS ELIBC FCDSL_CARDS FRITZCAPI_CARDS INPUT_DEVICES
KERNEL LINGUAS USERLAND VIDEO_CARDS"
USE_EXPAND_HIDDEN=""
USE_ORDER="env:pkg:conf:defaults"
VIDEO_CARDS="apm v4l nvidia nv"
XARGS="xargs -r"
XAUTHORITY="/root/.xauthVRSTJs"
_="/usr/bin/emerge"
[8.1.] Software (add the output of the ver_linux script here)
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux amd64 2.6.15-suspend2-r5 #5 PREEMPT Wed Feb 8 17:59:21 CET 2006
x86_64 AMD Athlon(tm) 64 Processor 3200+ AuthenticAMD GNU/Linux
Gnu C 4.0.2
Gnu make 3.80
binutils 2.16.1
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.2
e2fsprogs 1.38
reiserfsprogs line
reiser4progs line
PPP 2.4.3
nfs-utils 1.0.7
Linux C Library 2.3.6
Dynamic linker (ldd) 2.3.6
Procps 3.2.6
Net-tools 1.60
Kbd 1.12
Sh-utils 5.93
udev 084
Modules Loaded tuner saa7134 tda9887 video_buf v4l2_common
v4l1_compat ir_kbd_i2c ir_common videodev snd_seq_midi snd_emu10k1_synth
snd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_seq_oss
snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss b1pci b1dma b1 capi
capifs kernelcapi snd_emu10k1 snd_rawmidi snd_ac97_codec snd_ac97_bus
snd_pcm snd_seq_device snd_timer snd_page_alloc snd_util_mem snd_hwdep
snd soundcore 8250_pnp 8250 serial_core forcedeth 8139too mii nvidia eth1394
[8.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 4
model name : AMD Athlon(tm) 64 Processor 3200+
stepping : 8
cpu MHz : 803.924
cache size : 1024 KB
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm
3dnowext 3dnow
bogomips : 1608.88
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp
[8.3.] Module information (from /proc/modules):
tuner 39396 0 - Live 0xffffffff885e0000
saa7134 114216 0 - Live 0xffffffff885c3000
tda9887 14800 0 - Live 0xffffffff885eb000
video_buf 18244 1 saa7134, Live 0xffffffff885bd000
v4l2_common 6400 1 saa7134, Live 0xffffffff885ba000
v4l1_compat 11140 1 saa7134, Live 0xffffffff885b6000
ir_kbd_i2c 7436 1 saa7134, Live 0xffffffff885b3000
ir_common 8708 2 saa7134,ir_kbd_i2c, Live 0xffffffff885af000
videodev 9280 1 saa7134, Live 0xffffffff885ab000
snd_seq_midi 6976 0 - Live 0xffffffff885a8000
snd_emu10k1_synth 6656 0 - Live 0xffffffff885a5000
snd_emux_synth 33920 1 snd_emu10k1_synth, Live 0xffffffff8859b000
snd_seq_virmidi 6144 1 snd_emux_synth, Live 0xffffffff88598000
snd_seq_midi_emul 5696 1 snd_emux_synth, Live 0xffffffff88595000
snd_seq_oss 30948 0 - Live 0xffffffff8858c000
snd_seq_midi_event 6656 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss, Live
0xffffffff88589000
snd_seq 49240 8
snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event,
Live 0xffffffff8857b000
snd_pcm_oss 39008 0 - Live 0xffffffff88570000
snd_mixer_oss 15232 1 snd_pcm_oss, Live 0xffffffff8856b000
b1pci 7360 1 - Live 0xffffffff88566000
b1dma 13636 1 b1pci, Live 0xffffffff88561000
b1 22784 2 b1pci,b1dma, Live 0xffffffff8855a000
capi 14640 4 - Live 0xffffffff88555000
capifs 4752 2 capi, Live 0xffffffff88552000
kernelcapi 46112 4 b1pci,b1dma,b1,capi, Live 0xffffffff88545000
snd_emu10k1 112196 2 snd_emu10k1_synth, Live 0xffffffff88528000
snd_rawmidi 21920 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1, Live
0xffffffff88521000
snd_ac97_codec 98428 1 snd_emu10k1, Live 0xffffffff88507000
snd_ac97_bus 2432 1 snd_ac97_codec, Live 0xffffffff88505000
snd_pcm 81932 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec, Live
0xffffffff884ef000
snd_seq_device 7824 7
snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,
Live 0xffffffff884ec000
snd_timer 21256 3 snd_seq,snd_emu10k1,snd_pcm, Live 0xffffffff884e5000
snd_page_alloc 8400 2 snd_emu10k1,snd_pcm, Live 0xffffffff884e1000
snd_util_mem 3840 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff884df000
snd_hwdep 8392 2 snd_emux_synth,snd_emu10k1, Live 0xffffffff884db000
snd 53184 15
snd_emux_synth,snd_seq_virmidi,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_hwdep,
Live 0xffffffff884cd000
soundcore 8480 1 snd, Live 0xffffffff884c9000
8250_pnp 10496 0 - Live 0xffffffff884c5000
8250 20992 1 8250_pnp, Live 0xffffffff884be000
serial_core 18176 1 8250, Live 0xffffffff884b8000
forcedeth 21956 0 - Live 0xffffffff884b1000
8139too 22976 0 - Live 0xffffffff884aa000
mii 4928 1 8139too, Live 0xffffffff884a7000
nvidia 4847316 12 - Live 0xffffffff88006000
eth1394 17936 0 - Live 0xffffffff88000000
[8.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
0480-0487 : pnp 00:08
0810-0815 : ACPI CPU throttle
0970-0977 : 0000:00:0a.0
0970-0977 : sata_nv
09f0-09f7 : 0000:00:0a.0
09f0-09f7 : sata_nv
0b70-0b73 : 0000:00:0a.0
0b70-0b73 : sata_nv
0bf0-0bf3 : 0000:00:0a.0
0bf0-0bf3 : sata_nv
0cf8-0cff : PCI conf1
0d00-0d07 : pnp 00:08
0d00-0d07 : it87-isa
4000-4003 : PM1a_EVT_BLK
4004-4005 : PM1a_CNT_BLK
4008-400b : PM_TMR
401c-401c : PM2_CNT_BLK
4020-4027 : GPE0_BLK
5000-503f : 0000:00:01.1
5000-5007 : nForce2_smbus
5040-507f : 0000:00:01.1
5040-5047 : nForce2_smbus
5080-509f : 0000:00:01.1
b000-cfff : PCI Bus #02
b800-b87f : 0000:02:0b.0
bc00-bc1f : 0000:02:09.0
bc00-bc1e : b1pci-bc00
c000-c03f : 0000:02:09.0
c400-c41f : 0000:02:08.0
c400-c41f : EMU10K1
c800-c8ff : 0000:02:07.0
c800-c8ff : 8139too
cc00-cc07 : 0000:02:08.1
d000-d07f : 0000:00:0a.0
d000-d07f : sata_nv
d400-d40f : 0000:00:0a.0
d400-d40f : sata_nv
ec00-ec07 : 0000:00:05.0
ec00-ec07 : forcedeth
ffa0-ffaf : 0000:00:08.0
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-3ffbffff : System RAM
00100000-003ceeaa : Kernel code
003ceeab-0051962f : Kernel data
3ffc0000-3ffcffff : ACPI Tables
3ffd0000-3fffffff : ACPI Non-volatile Storage
9a800000-ba7fffff : PCI Bus #01
a0000000-afffffff : 0000:01:00.0
a0000000-afffffff : vesafb
c0000000-dfffffff : 0000:00:00.0
fa900000-fe9fffff : PCI Bus #01
fc000000-fcffffff : 0000:01:00.0
fd000000-fdffffff : 0000:01:00.0
fd000000-fdffffff : nvidia
fe9e0000-fe9fffff : 0000:01:00.0
fea00000-feafffff : PCI Bus #02
feaff000-feaff7ff : 0000:02:0b.0
feaff000-feaff7ff : ohci1394
feaff800-feaffbff : 0000:02:0a.0
feaff800-feaffbff : saa7134[0]
feaffc00-feaffcff : 0000:02:07.0
feaffc00-feaffcff : 8139too
febfc000-febfcfff : 0000:00:05.0
febfc000-febfcfff : forcedeth
febfd000-febfdfff : 0000:00:02.0
febfd000-febfdfff : ohci_hcd
febfe000-febfefff : 0000:00:02.1
febfe000-febfefff : ohci_hcd
febffc00-febffcff : 0000:00:02.2
febffc00-febffcff : ehci_hcd
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ff7c0000-ffffffff : reserved
[8.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=512M]
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=14 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut-
LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+
500MHz+ 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz-
500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE-
CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [c0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+
Rate=x8
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management
(rev a1)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 5080 [size=32]
Region 4: I/O ports at 5000 [size=64]
Region 5: I/O ports at 5040 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
(prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
(prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0
Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 18
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 80a7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec00 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller
(v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller
(v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: I/O ports at d000 [size=128]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI
Bridge (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fa900000-fe9fffff
Prefetchable memory behind bridge: 9a800000-ba7fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge
(rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR+ <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
I/O behind bridge: 0000b000-0000cfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr+ DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800
GT] (rev a1) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at a0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at fe9e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
FW+ Rate=x8
02:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs SBLive! 5.1 Model SB0100
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at c400 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
(rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at cc00 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:09.0 Network controller: AVM Audiovisuelles MKTG & Computer System
GmbH B1 ISDN
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at c000 [size=64]
Region 1: I/O ports at bc00 [size=32]
02:0a.0 Multimedia controller: Philips Semiconductors SAA7134 Video
Broadcast Decoder (rev 01)
Subsystem: Pinnacle Systems Inc. Pinnacle PCTV 300i DVB-T + PAL
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (62000ns min, 62000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
02:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at b800 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[8.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
[8.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
Nothing more ;-)
[X.] Other notes, patches, fixes, workarounds:
The rmmod/modprobe fun from above is a very, very bad workaround.
Thanks in advance
Christian
--
Tel.: 0641-2097252, Mobil: 0171-3611230
PGP: http://www.roessner-net.com/0x6B929997.asc
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
