Re: 2.6.16-rc1-mm4

[Andrew Morton <akpm@osdl.org>]

Al Boldi <a1426z@gawab.com> wrote:
>
> Andrew Morton wrote:
> > Al Boldi <a1426z@gawab.com> wrote:
> > > Andrew Morton wrote:
> > > > - Various other random bits and pieces.  Things have been pretty quiet
> > > >   lately - most activity seems to be concentrated about putting bugs
> > > > into the various subsystem trees.
> > >
> > > Does it fix the DRM_i810 hang during a suspend-to-ram/disk cycle?
> >
> > I don't know - I don't watch every patch which goes into 49 different
> > trees.  Did you try it?
> 
> It still hangs w/ drm.
> 
> w/o drm STD works like a charm.

OK.

> w/o drm STR works lest this t/o and a noisy display in X.

What do "lest" and "t/o" mean?  Please use less abbreviations.

> Stopping tasks: ========================|
> Suspending device 0.1
> Suspending device 0.0
> Suspending device ide0
> Suspending device floppy.0
> Suspending device serio1
> Suspending device serio0
> Suspending device i8042
> Suspending device 0000:01:0a.0
> Suspending device 0000:01:05.0
> Suspending device 0000:00:1f.2
> Suspending device 0000:00:1f.1
> Suspending device 0000:00:1f.0
> Suspending device 0000:00:1e.0
> Suspending device 0000:00:01.0
> Suspending device 0000:00:00.0
> Suspending device pci0000:00
> Suspending device platform
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> Back to C!
> ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> 
> IRQ 11
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> hda: drive not ready on wakeup
> hda: status timeout: status=0xd0 { Busy }
> ide: failed opcode was: unknown
> hda: DMA disabled
> hdb: DMA disabled
> hda: drive not ready for command
> ide0: reset: success
> BUG: warning at drivers/ide/ide-iops.c:1235/ide_wait_not_busy()
>  <c02612e2> ide_wait_not_busy+0xa2/0xb0   <c025ee87> 
> start_request+0x1a7/0x230
>  <c025f17a> ide_do_request+0x23a/0x3c0   <c026440a> 
> set_multmode_intr+0x1a/0x70
>  <c025f79b> ide_intr+0xeb/0x130   <c02643f0> set_multmode_intr+0x0/0x70
>  <c0135610> handle_IRQ_event+0x30/0x70   <c01356a5> __do_IRQ+0x55/0xc0
>  <c0105672> do_IRQ+0x42/0x70  
>  =======================
>  <c0103976> common_interrupt+0x1a/0x20   <c021886d> 
> acpi_processor_idle+0x2b6/0x332
>  <c0101030> default_idle+0x0/0x70   <c0101118> cpu_idle+0x58/0x70
>  <c03c47bd> start_kernel+0x14d/0x170   <c03c4310> 
> unknown_bootoption+0x0/0x1e0
> hdb: set_drive_speed_status: status=0x40 { DriveReady }
> ide: failed opcode was: unknown
> Restarting tasks... done

The above is an IDE problem.  Are you saying that the above only occurs
when DRM is enabled?

Please take more time and use more words when describing this problem, thanks.

> Also, a 100HZ recompile in mainline causes a 400% delay doing a simple lilo, 
> which seems fixed in mm.  Is there a reason you can't move that to mainline?

Again, I don't understand what that means.  Are you saying that a kernel
compiled with HZ=100 takes 4 times as long to run lilo?

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/