Re: 2.6.16-rc1-mm4

[Al Boldi <a1426z@gawab.com>]

Andrew Morton wrote:
> Al Boldi <a1426z@gawab.com> wrote:
> > Andrew Morton wrote:
> > > - Various other random bits and pieces.  Things have been pretty quiet
> > >   lately - most activity seems to be concentrated about putting bugs
> > > into the various subsystem trees.
> >
> > Does it fix the DRM_i810 hang during a suspend-to-ram/disk cycle?
>
> I don't know - I don't watch every patch which goes into 49 different
> trees.  Did you try it?

It still hangs w/ drm.

w/o drm STD works like a charm.
w/o drm STR works lest this t/o and a noisy display in X.

Stopping tasks: ========================|
Suspending device 0.1
Suspending device 0.0
Suspending device ide0
Suspending device floppy.0
Suspending device serio1
Suspending device serio0
Suspending device i8042
Suspending device 0000:01:0a.0
Suspending device 0000:01:05.0
Suspending device 0000:00:1f.2
Suspending device 0000:00:1f.1
Suspending device 0000:00:1f.0
Suspending device 0000:00:1e.0
Suspending device 0000:00:01.0
Suspending device 0000:00:00.0
Suspending device pci0000:00
Suspending device platform
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Back to C!
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> 
IRQ 11
PCI: Setting latency timer of device 0000:00:1e.0 to 64
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
hda: drive not ready on wakeup
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: DMA disabled
hdb: DMA disabled
hda: drive not ready for command
ide0: reset: success
BUG: warning at drivers/ide/ide-iops.c:1235/ide_wait_not_busy()
 <c02612e2> ide_wait_not_busy+0xa2/0xb0   <c025ee87> 
start_request+0x1a7/0x230
 <c025f17a> ide_do_request+0x23a/0x3c0   <c026440a> 
set_multmode_intr+0x1a/0x70
 <c025f79b> ide_intr+0xeb/0x130   <c02643f0> set_multmode_intr+0x0/0x70
 <c0135610> handle_IRQ_event+0x30/0x70   <c01356a5> __do_IRQ+0x55/0xc0
 <c0105672> do_IRQ+0x42/0x70  
 =======================
 <c0103976> common_interrupt+0x1a/0x20   <c021886d> 
acpi_processor_idle+0x2b6/0x332
 <c0101030> default_idle+0x0/0x70   <c0101118> cpu_idle+0x58/0x70
 <c03c47bd> start_kernel+0x14d/0x170   <c03c4310> 
unknown_bootoption+0x0/0x1e0
hdb: set_drive_speed_status: status=0x40 { DriveReady }
ide: failed opcode was: unknown
Restarting tasks... done

Also, a 100HZ recompile in mainline causes a 400% delay doing a simple lilo, 
which seems fixed in mm.  Is there a reason you can't move that to mainline?

Thanks!

--
Al

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/