Re: 2.6.15-rt4 failure with LATENCY_TRACE on x86_64

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

On Fri, 2006-01-13 at 10:54 -0500, Steven Rostedt wrote:
>  
> > > Have you tried booting with idle=poll? I wonder if that would help?
> > 
> > No, I thought that was strictly an SMP issue. I'll try it as well.
> 
> It effects SMP mostly.  I doubt that it will effect UP, but the tsc is
> still not consistent.

I tried rt4-sr2 and got the same results (also with idle=poll for
completeness :). 

I'm beginning to think that it's some sort of interaction with the BIOS
(either that or just weird hardware). When I compared the two sets of
boot outputs, the boot that succeeded (dmesg-rt4-sr2.good.txt, with
WAKEUP_TIMING, LATENCY_TIMING and LATENCY_TRACE turned off) shows APIC
probes and PCI probes that don't have corresponding prints in the failed
boot (dmesg-rt4-sr2.fail.txt). 

I tried booting variously with:
	pci=routeirq
	acpi=noirq
	lapic
but saw no change in behavior.

Have you tried booting your system with a up kernel?

Clark

-- 
Clark Williams <[email protected]>

Bootdata ok (command line is ro root=/dev/sda2 console=ttyS0,115200 console=tty0)
Linux version 2.6.15-rt4-sr2 ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #4 PREEMPT Fri Jan 13 12:43:09 CST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Checking aperture...
CPU 0: aperture @ e0000000 size 128 MB
Real-Time Preemption Support (C) 2004-2005 Ingo Molnar
Built 1 zonelists
Kernel command line: ro root=/dev/sda2 console=ttyS0,115200 console=tty0
Initializing CPU#0
WARNING: experimental RCU implementation.
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1999.480 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 491540k/524224k available (2228k kernel code, 32296k reserved, 1327k data, 184k init)
Calibrating delay using timer specific routine.. 3999.67 BogoMIPS (lpj=1999839)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
Detected 12.496 MHz APIC timer.
testing NMI watchdog ... OK.
checking if image is initramfs... it is
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xe0000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e8000000-e9ffffff
  PREFETCH window: d0000000-dfffffff
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1137180272.734:1): initialized
Total HugeTLB memory allocated, 0
Time: tsc clocksource has been installed.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 169
ACPI: PCI interrupt for device 0000:00:02.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 1
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:pio
hdc: AOPEN COM5232/AAH PRO, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 8, 1179648 bytes)
input: AT Translated Set 2 keyboard as /class/input/input0
TCP bind hash table entries: 16384 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    2 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
cpu_init done, current fid 0xc, vid 0x2
ACPI wakeup devices:
FUTS PCI0 USB0 USB1 USB2 USB3 MAC0 AMR0 UAR1 PS2M PS2K
ACPI: (supports S0 S1 S4 S5)
*****************************************************************************
*                                                                           *
*  REMINDER, the following debugging option is turned on in your .config:   *
*                                                                           *
*        CONFIG_LATENCY_TRACE                                               *
*                                                                           *
*  it may increase runtime overhead and latencies.                          *
*                                                                           *
*****************************************************************************
Freeing unused kernel memory: 184k freed
logips2pp: Detected unknown logitech mouse model 1
SCSI subsystem initialized
sata_sis 0000:00:05.0: version 0.5
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 177
sata_sis 0000:00:05.0: Detected SiS 180/181 chipset in SATA mode
ata1: SATA max UDMA/133 cmd 0xE500 ctl 0xE602 bmdma 0xE900 irq 177
ata2: SATA max UDMA/133 cmd 0xE700 ctl 0xE802 bmdma 0xE908 irq 177
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_sis
ata2: no device found (phy stat 00000000)
scsi1 : sata_sis
  Vendor: ATA       Model: HDS728080PLA380   Rev: PF2O
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
init[1]: segfault at ffffffff8010fadc rip ffffffff8010fadc rsp 00007fffffd03f08 error 15
init[1]: segfault at ffffffff8010fadc rip ffffffff8010fadc rsp 00007fffffd03f08 error 15
init[1]: segfault at ffffffff8010fadc rip ffffffff8010fadc rsp 00007fffffd03f08 error 15
init[1]: segfault at ffffffff8010fadc rip ffffffff8010fadc rsp 00007fffffd03f08 error 15
init[1]: segfault at ffffffff8010fadc rip ffffffff8010fadc rsp 00007fffffd03f08 error 15


Bootdata ok (command line is ro root=/dev/sda2 console=ttyS0,115200 console=tty0)
Linux version 2.6.15-rt4-sr2 ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #3 PREEMPT Fri Jan 13 12:12:19 CST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 AWARD                                 ) @ 0x00000000000f6eb0
ACPI: RSDT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000001fff3000
ACPI: FADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000001fff3040
ACPI: MADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000001fff6b80
ACPI: DSDT (v001 AWARD  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 128075
  DMA zone: 2850 pages, LIFO batch:0
  DMA32 zone: 125225 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Checking aperture...
CPU 0: aperture @ e0000000 size 128 MB
Real-Time Preemption Support (C) 2004-2005 Ingo Molnar
Built 1 zonelists
Kernel command line: ro root=/dev/sda2 console=ttyS0,115200 console=tty0
Initializing CPU#0
WARNING: experimental RCU implementation.
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1999.481 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 510156k/524224k available (2169k kernel code, 13680k reserved, 1326k data, 184k init)
Calibrating delay using timer specific routine.. 3999.43 BogoMIPS (lpj=1999719)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
Detected 12.496 MHz APIC timer.
testing NMI watchdog ... OK.
checking if image is initramfs... it is
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xe0000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e8000000-e9ffffff
  PREFETCH window: d0000000-dfffffff
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1137177211.587:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Time: tsc clocksource has been installed.
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 169
ACPI: PCI interrupt for device 0000:00:02.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 1
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: AOPEN COM5232/AAH PRO, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
input: AT Translated Set 2 keyboard as /class/input/input0
TCP established hash table entries: 16384 (order: 8, 1179648 bytes)
TCP bind hash table entries: 16384 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    2 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
cpu_init done, current fid 0xc, vid 0x2
ACPI wakeup devices: 
FUTS PCI0 USB0 USB1 USB2 USB3 MAC0 AMR0 UAR1 PS2M PS2K 
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 184k freed
SCSI subsystem initialized
libata version 1.20 loaded.
sata_sis 0000:00:05.0: version 0.5
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 177
sata_sis 0000:00:05.0: Detected SiS 180/181 chipset in SATA mode
ata1: SATA max UDMA/133 cmd 0xE500 ctl 0xE602 bmdma 0xE900 irq 177
ata2: SATA max UDMA/133 cmd 0xE700 ctl 0xE802 bmdma 0xE908 irq 177
logips2pp: Detected unknown logitech mouse model 1
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_sis
ata2: no device found (phy stat 00000000)
scsi1 : sata_sis
  Vendor: ATA       Model: HDS728080PLA380   Rev: PF2O
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
security:  3 users, 6 roles, 888 types, 109 bools
security:  55 classes, 244070 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev sda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 177
e100: eth0: e100_probe: addr 0xea124000, irq 177, MAC addr 00:90:27:DE:09:73
sis900.c: v1.08.08 Jan. 22 2005
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 185
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth1: SiS 900 PCI Fast Ethernet at 0xe400, IRQ 185, 00:11:5b:8e:b9:8a.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:03.3: EHCI Host Controller
PCI: cache line size of 64 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: irq 193, io mem 0xea121000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 201
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 201, io mem 0xea123000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 209
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 209, io mem 0xea125000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 217
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 217, io mem 0xea120000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [FUTS]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
cdrom: open failed.
cdrom: open failed.
EXT3 FS on sda2, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2096472k swap on /dev/sda3.  Priority:-1 extents:1 across:2096472k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth1: Media Link On 100mbps half-duplex 
sed[1377] general protection rip:30ba7041b1 rsp:7fffffffe620 error:0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
SELinux: initialized (dev 0:14, type nfs), uses genfs_contexts
SELinux: initialized (dev 0:15, type nfs), uses genfs_contexts

Attachment: signature.asc
Description: This is a digitally signed message part

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux