agp_backend_initialize() failed on ServerWorks CNB20LE

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,

On a server with ServerWorks CNB20LE and CONFIG_AGP_SWORKS enabled
I get these upon bootup:
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.1 failed with error -22

lspci -vvv shows (i skipped the IDE, ISA and NIC lines):
00:00.0 Host bridge: ServerWorks CNB20LE Host Bridge (rev 06)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 64, cache line size 08

00:00.1 Host bridge: ServerWorks CNB20LE Host Bridge (rev 06)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, cache line size 08

00:02.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] (rev 7a) (prog-if 00 [VGA])
        Subsystem: Intel Corporation: Unknown device 4756
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min), cache line size 08
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
        Region 1: I/O ports at 5000 [size=256]
        Region 2: Memory at fb100000 (32-bit, non-prefetchable) [size=4K]
        Expansion ROM at 50000000 [disabled] [size=128K]
        Capabilities: [5c] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


The only problems I have that *may* be related to these messages is the
fact that when I boot into X and try to switch to a text console, the
screen gets garbled and freezes, the server works fine besides the
screen throwing trash at me.
It is not a big issue, but maybe anyone would like to know.
Or enlighten me if it

Regards,
Maciej


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]
  Powered by Linux