Re: aic7xxx regression occuring after 2.6.12 final

[Tony Vroon <tony@vroon.org>]

On Sat, 2005-07-02 at 20:03 +0100, Tony Vroon wrote:
> Output follows:
It got mangled somehow. Not sure what happened but it's corrupted near
the end. Reposting:
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 29160 Ultra160 SCSI adapter>
        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

scsi0: Slave Alloc 0
(scsi0:A:0:0): Sending WDTR 0
(scsi0:A:0:0): Received WDTR 0 filtered to 0
 target0:0:0: FAST-5 SCSI 1.0 MB/s ST (1020 ns, offset 255)
scsi0: target 0 using 8bit transfers
(scsi0:A:0:0): Sending SDTR period 45, offset 0
(scsi0:A:0:0): Received SDTR period 45, offset 0
Filtered to period 0, offset 0
 target0:0:0: asynchronous.
scsi0: target 0 using asynchronous transfers
 Vendor: FUJITSU   Model: MAP3367NP         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0: Slave Configure 0
 target0:0:0: asynchronous.
scsi0:A:0:0:0: Tagged Queuing enabled.  Depth 32
 target0:0:0: Beginning Domain Validation
(scsi0:A:0:0): Sending WDTR 1
(scsi0:A:0:0): Received WDTR 1 filtered to 1
 target0:0:0: FAST-5 WIDE SCSI 2.0 MB/s ST (1020 ns, offset 255)
scsi0: target 0 using 16bit transfers
(scsi0:A:0:0): Sending SDTR period 45, offset 0
(scsi0:A:0:0): Received SDTR period 45, offset 0
Filtered to period 0, offset 0
 target0:0:0: wide asynchronous
csi0: target 0 using asynchronous transfers
(scsi0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options
7
(scsi0:A:0:0): Received PPR bus_width 1, period 9, offset 7f,
ppr_options 7
Filtered to width 1, period 9, offset 7f, options 7
 target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s ST IU (12.5ns, offset 127)
scsi0: target 0 synchronous at 80.0MHz DT, offset = 0x7
(scsi0:A:0:0): Unexpected busfree in Message-in phase
SEQADDR == 0x16b
 target0:0:0: Write Buffer failure 70000
 target0:0:0: Domain Validation Disabling Information Units
(scsi0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options
6
(scsi0:A:0:0): refuses tagged comands.  Performing non-tagged I/O
 target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s ST IU (12.5 ns, offset 127)
*PC hangs here*

Attachment: signature.asc
Description: This is a digitally signed message part