Re: 2.6.12 can not support via rhine?

[guorke <gourke@gmail.com>]

who can give helps?
Thanks

On 6/23/05, guorke <gourke@gmail.com> wrote:
> VFS: Mounted root (ext3 filesystem) readonly. |VFS: Mounted root (ext3
> filesystem) readonly.
> better is
> Freeing unused kernel memory: 220k freed      | Freeing unused kernel
> memory... freed
> kjournald starting.  Commit interval 5 seconds <
> EXT3 FS on hda1, internal journal                  | EXT3 FS on hda1,
> internal journal
> Adding 265064k swap on /dev/hda2.....          | Adding 265064k swap
> /dev/hda2. ...
> via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004..                        <
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12              <
> PCI: setting IRQ 12 as level-triggered                                  <
> ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
> eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12.     <
> eth0: MII PHY found at address 8, status 0x782d advertising <
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1               <
> 
> 
> 
> On 6/23/05, guorke <gourke@gmail.com> wrote:
> > hi
> > when i reboot use 2.6.11,it's ok.
> > but when i use 2.6.12 kernel, i get this:
> >
> > via rhine device dose not seem to be present , delaying eth0 initialzation..
> > but in 2.6.11, it's say ok, I must say i have add via rhine support.
> > this following is difference output demsg :
> > diff -y dmesg_2.6.11 dmesg_2.6.12
> >
> > VFS: Mounted root (ext3 filesystem) readonly.                   VFS:
> > Mounted root (ext3 filesystem) readonly.
> > Freeing unused kernel memory: 220k freed                      |
> > Freeing unused kernel memory: 224k freed
> > kjournald starting.  Commit interval 5 seconds                <
> > EXT3 FS on hda1, internal journal                               EXT3
> > FS on hda1, internal journal
> > Adding 265064k swap on /dev/hda2.  Priority:-1 extents:1        Adding
> > 265064k swap on /dev/hda2.  Priority:-1 extents:1
> > via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald  <
> > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12             <
> > PCI: setting IRQ 12 as level-triggered                        <
> > ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
> > eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12.     <
> > eth0: MII PHY found at address 8, status 0x782d advertising 0 <
> > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1               <
> >
> > like no via rhine.
> >
> > Thanks
> >
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/