It seems that I know the reason why is disabled my wifi...
it's looks like the rfkill is active - as I have get acquainted this thing - it means that for spare battery power you could turn off the wifi chip. This is the rfkill. But I couldn't turn off this - or manage. Normally as far as I know, Networkmanager could do this at in right click menu, and manage this part. But currently the whole network managing upper part is greyed out - so it means for me that unreachable.
Somebodí at support chat has adviced to me to install system-config-network - this helped to me a lot to get the diagnosis.
So - I hope this will help if somebody knows the solution for this - here is the part of the dmesg:
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
RTNETLINK answers: Operation not possible due to RF-kill
Error for wireless request "Set Frequency" (8B04) :
invalid argument "Automatic".
Thx,
Zoltan
2010/9/5 Zoltan Hoppar <hopparz@xxxxxxxxx>
Thanks,
I knew this, but doesnt work. However I have insterted successfully the b43 driver, but somehow gets disabled my wireless network. I think this is causing by NetworkManager, but couldn't tell that why. Maybe I don't have right, but currently I'm stucked with an disabled Broadcom-PHY. Well, it seems in dmesg that first turns on the PHY then turns off???
Here is my part of the dmesg:
sky2 0000:02:00.0: eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
b43 ssb0:0: firmware: requesting b43/ucode15.fw
b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
ADDRCONF(NETDEV_UP): wlan0: link is not ready
sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control both
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
b43-phy0: Radio hardware status changed to DISABLED
Furthermore, on networkmanager gui where you could turn off/on the networks (right click on upper systray icon), greyed out - so couldn't explain what happened...
PS: If I would like to always load an module for my computer, where must I note that for the system? (HP WMI driver module)2010/9/4 Athmane Madjoudj <athmanem@xxxxxxxxx>
On 09/04/2010 09:24 PM, Zoltan Hoppar wrote:> followed many advices - linuxwireless.org <http://linuxwireless.org> and
> Hi Everyone,
>
> I have a little problems with my new laptop HP Probook 4515s with Fedora
> 13, and the latest kernel.
>
> 1. Somehow, I couldn't activate the broadcom PHY - wifi module, I have
> after many tries I have given up. In result I got only an broken networkTry the following:
> manager.
1. Enable RPMFusion repo (both free and non-free). [1]
2. as root:
# yum install kmod-wl broadcom-wl
[1] http://rpmfusion.org/Configuration
HTH
[... SNIP ...]
--
Athmane Madjoudj
--
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
--
PGP: 06853DF7
--
PGP: 06853DF7
-- users mailing list users@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe or change subscription options: https://admin.fedoraproject.org/mailman/listinfo/users Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
