I added a scsi disk to a machine (fedora is 10 installed to sata disk) but mounting fails. I boot the machine, I get a mount failure, it tells me to enter root password or ctrl-d to reboot then (just to taunt me) I get sdb info. Probably an easy fix, for those who know the subtle details of the boot sequence. Short excerpt from dmesg showing, scsi finding disk4, then mounting root file system, then creating sd 4:0:0:0: [sdb] ---------- scsi4 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec AIC7901 Ultra320 SCSI adapter> aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs EDAC e752x: tolm = 80000, remapbase = ffc000, remaplimit = 0 EDAC MC0: Giving out device to 'e752x_edac' 'E7525': DEV 0000:00:00.0 EDAC PCI0: Giving out device to module 'e752x_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED) e1000 0000:03:0e.0: PCI INT A -> GSI 48 (level, low) -> IRQ 48 i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 scsi 4:0:0:0: Direct-Access SEAGATE ST373454LW D403 PQ: 0 ANSI: 3 scsi target4:0:0: asynchronous scsi4:A:0:0: Tagged Queuing enabled. Depth 4 scsi target4:0:0: Beginning Domain Validation scsi target4:0:0: wide asynchronous scsi target4:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RDSTRM RTI WRFLOW PCOMP (6.25 ns, offset 63) e1000: 0000:03:0e.0: e1000_probe: (PCI-X:100MHz:64-bit) 00:13:72:88:ae:dc scsi target4:0:0: Ending Domain Validation e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection device-mapper: multipath: version 1.0.5 loaded EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on dm-1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 4128760k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:4128760k IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx> firmware: requesting intel-ucode/0f-04-0a firmware: requesting intel-ucode/0f-04-0a firmware: requesting intel-ucode/0f-04-0a firmware: requesting intel-ucode/0f-04-0a p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready sd 4:0:0:0: [sdb] 143374650 512-byte hardware sectors (73408 MB) sd 4:0:0:0: [sdb] Write Protect is off sd 4:0:0:0: [sdb] Mode Sense: ab 00 10 08 sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 4:0:0:0: [sdb] 143374650 512-byte hardware sectors (73408 MB) sd 4:0:0:0: [sdb] Write Protect is off sd 4:0:0:0: [sdb] Mode Sense: ab 00 10 08 -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
