Hi,
I have been asked to look at a server that has some disk issues.
If I try and do a ls /boot I get the following:
# ls /boot
ls: reading directory /boot: Input/output error
I have been told that the disks use multipath but I have no experience
of this to date.
I know the disks are on a SAN but as yet have not been able to locate
them using the IBM SAN manager.
Can someone help me unravel what I can do to get this server healthy again.
This is the dmesg file during the boot up
Linux version 2.6.18-53.1.21.el5PAE
(brewbuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2 20070626
(Red Hat 4.1.2-14)) #1 SMP Wed May 7 08:56:33 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000cffbce40 (usable)
BIOS-e820: 00000000cffbce40 - 00000000cffd0000 (ACPI data)
BIOS-e820: 00000000cffd0000 - 00000000d0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
3968MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 0009d940
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 1245184
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 1015808 pages, LIFO batch:31
DMI 2.4 present.
Using APIC driver default
ACPI: RSDP (v002 IBM ) @ 0x000fdfd0
ACPI: XSDT (v001 IBM SERBLADE 0x00001001 IBM 0x45444f43) @ 0xcffcff00
ACPI: FADT (v002 IBM SERBLADE 0x00001001 IBM 0x45444f43) @ 0xcffcfe40
ACPI: MADT (v001 IBM SERBLADE 0x00001001 IBM 0x45444f43) @ 0xcffcfdc0
ACPI: MCFG (v001 IBM SERBLADE 0x00001001 IBM 0x45444f43) @ 0xcffcfd80
ACPI: DSDT (v002 IBM SERBLADE 0x00001000 INTL 0x20060707) @ 0x00000000
ACPI: PM-Timer IO Port: 0x588
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 14, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x0d] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 13, version 32, address 0xfec80000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Detected 3000.364 MHz processor.
Built 1 zonelists. Total pages: 1245184
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
crashkernel=128M@16M
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0740000 soft=c0720000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 4014432k/4980736k available (2078k kernel code, 178348k
reserved, 859k data, 220k init, 3276528k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6002.55 BogoMIPS (lpj=3001278)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000
0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000
0004e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000940
0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 0b
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c0741000 soft=c0721000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5999.36 BogoMIPS (lpj=2999682)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000
0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000
0004e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000940
0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 0b
Total of 2 processors activated (12001.92 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
migration_cost=60
checking if image is initramfs... it is
Freeing initrd memory: 3456k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:01:01.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI7.PCIX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI7.PCI9.PCIA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI7.PCI9.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIF._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIS._PRT]
ACPI: PCI Interrupt Link [LP00] (IRQs *4)
ACPI: PCI Interrupt Link [LP01] (IRQs *5)
ACPI: PCI Interrupt Link [LP02] (IRQs *11)
ACPI: PCI Interrupt Link [LP03] (IRQs *5)
ACPI: Blank IRQ resource
ACPI: Resource is not an IRQ entry
ACPI: PCI Interrupt Link [LP04] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [LP05] (IRQs *5)
ACPI: PCI Interrupt Link [LP06] (IRQs *11)
ACPI: PCI Interrupt Link [LP07] (IRQs *5)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0xc00-0xc1f has been reserved
pnp: 00:01: ioport range 0xc60-0xc67 has been reserved
pnp: 00:08: ioport range 0xc28-0xc28 has been reserved
pnp: 00:08: ioport range 0xc2c-0xc2c has been reserved
PCI: Bridge: 0000:09:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:09:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:07:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:07:00.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
IO window: 5000-5fff
MEM window: d5000000-d6ffffff
PREFETCH window: d1200000-d12fffff
PCI: Bridge: 0000:0e:00.0
IO window: disabled.
MEM window: d3000000-d40fffff
PREFETCH window: d1300000-d13fffff
PCI: Bridge: 0000:00:05.0
IO window: 6000-ffff
MEM window: d2000000-d4ffffff
PREFETCH window: d1300000-d13fffff
PCI: Bridge: 0000:03:00.0
IO window: disabled.
MEM window: da000000-dcffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: da000000-dcffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:05:00.0
IO window: disabled.
MEM window: d7000000-d9ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: d7000000-d9ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: 4000-4fff
MEM window: dd000000-deffffff
PREFETCH window: d1000000-d11fffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: f8000000-f8ffffff
PREFETCH window: f0000000-f7ffffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:07:00.0 to 64
PCI: Setting latency timer of device 0000:09:00.0 to 64
PCI: Setting latency timer of device 0000:09:01.0 to 64
PCI: Setting latency timer of device 0000:07:00.3 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:0e:00.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:03:00.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
PCI: Setting latency timer of device 0000:05:00.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1227304573.017:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 71A43366C4B1FE3A
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:07:00.0 to 64
Allocate Port Service[0000:07:00.0:pcie10]
Allocate Port Service[0000:07:00.0:pcie11]
PCI: Setting latency timer of device 0000:09:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:09:00.0:pcie20]
Allocate Port Service[0000:09:00.0:pcie21]
PCI: Setting latency timer of device 0000:09:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:09:01.0:pcie20]
Allocate Port Service[0000:09:01.0:pcie21]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 220k freed
Write protecting the kernel read-only data: 387k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 18 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 66, io base 0x00002200
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 74, io base 0x00002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 19 (level, low) -> IRQ 82
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 82, io base 0x00002800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
usb 1-2: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 90
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 90, io mem 0xf9000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
SCSI subsystem initialized
QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 98
qla2xxx 0000:0c:00.0: Found an ISP2432, irq 98, iobase 0xf8806000
qla2xxx 0000:0c:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:0c:00.0 to 64
qla2xxx 0000:0c:00.0: Configure NVRAM parameters...
qla2xxx 0000:0c:00.0: Verifying loaded RISC code...
qla2xxx 0000:0c:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:0c:00.0: Allocated (901 KB) for firmware dump...
scsi0 : qla2xxx
qla2xxx 0000:0c:00.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k7
QLogic QMI3472 - QMC2422M
ISP2432: PCIe (2.5Gb/s x4) @ 0000:0c:00.0 hdma+, host#=0, fw=4.00.150 [IP]
ACPI: PCI Interrupt 0000:0c:00.1[B] -> GSI 18 (level, low) -> IRQ 66
qla2xxx 0000:0c:00.1: Found an ISP2432, irq 66, iobase 0xf881a000
qla2xxx 0000:0c:00.1: Configuring PCI space...
PCI: Setting latency timer of device 0000:0c:00.1 to 64
qla2xxx 0000:0c:00.1: Configure NVRAM parameters...
qla2xxx 0000:0c:00.1: Verifying loaded RISC code...
usb 4-3: new high speed USB device using ehci_hcd and address 3
usb 4-3: configuration #1 chosen from 1 choice
hub 4-3:1.0: USB hub found
hub 4-3:1.0: 2 ports detected
qla2xxx 0000:0c:00.1: Allocated (64 KB) for EFT...
qla2xxx 0000:0c:00.1: Allocated (901 KB) for firmware dump...
scsi1 : qla2xxx
qla2xxx 0000:0c:00.1:
QLogic Fibre Channel HBA Driver: 8.01.07-k7
QLogic QMI3472 - QMC2422M
ISP2432: PCIe (2.5Gb/s x4) @ 0000:0c:00.1 hdma+, host#=1, fw=4.00.150 [IP]
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.04
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
mptbase: Initiating ioc0 bringup
qla2xxx 0000:0c:00.0: LOOP UP detected (4 Gbps).
usb 1-2: new full speed USB device using uhci_hcd and address 3
ioc0: SAS1064E: Capabilities={Initiator}
PCI: Setting latency timer of device 0000:02:00.0 to 64
qla2xxx 0000:0c:00.1: LOOP UP detected (4 Gbps).
usb 1-2: configuration #1 chosen from 1 choice
input: IBM IBM MM2 as /class/input/input0
input: USB HID v1.10 Keyboard [IBM IBM MM2] on usb-0000:00:1d.0-2
input: IBM IBM MM2 as /class/input/input1
input: USB HID v1.10 Mouse [IBM IBM MM2] on usb-0000:00:1d.0-2
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 62914560 512-byte hdwr sectors (32212 MB)
sda: Write Protect is off
sda: Mode Sense: 77 00 10 08
SCSI device sda: drive cache: write back w/ FUA
SCSI device sda: 62914560 512-byte hdwr sectors (32212 MB)
sda: Write Protect is off
sda: Mode Sense: 77 00 10 08
SCSI device sda: drive cache: write back w/ FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 157286400 512-byte hdwr sectors (80531 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
SCSI device sdb: 157286400 512-byte hdwr sectors (80531 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
sdb:<5> Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 62914560 512-byte hdwr sectors (32212 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
SCSI device sdc: 62914560 512-byte hdwr sectors (32212 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
sdc: sdc1 sdc2
sd 1:0:0:0: Attached scsi disk sdc
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 157286400 512-byte hdwr sectors (80531 MB)
sdd: Write Protect is off
sdd: Mode Sense: 77 00 10 08
SCSI device sdd: drive cache: write back w/ FUA
SCSI device sdd: 157286400 512-byte hdwr sectors (80531 MB)
sdd: Write Protect is off
sdd: Mode Sense: 77 00 10 08
SCSI device sdd: drive cache: write back w/ FUA
sdd:end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
Dev sdb: unable to read RDB block 0
end_request: I/O error, dev sdd, sector 0
Dev sdd: unable to read RDB block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdd, sector 0
scsi2 : ioc0: LSISAS1064E, FwRev=01160000h, Ports=1, MaxQ=286, IRQ=169
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 90
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00012a00 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00012a08 irq 15
end_request: I/O error, dev sdb, sector 0
unable to read partition table
sd 0:0:0:1: Attached scsi disk sdb
Vendor: IBM Model: Universal Xport Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sde: 62914560 512-byte hdwr sectors (32212 MB)
sde: Write Protect is off
sde: Mode Sense: 77 00 10 08
SCSI device sde: drive cache: write back w/ FUA
SCSI device sde: 62914560 512-byte hdwr sectors (32212 MB)
sde: Write Protect is off
sde: Mode Sense: 77 00 10 08
SCSI device sde: drive cache: write back w/ FUA
sde:<7>ata2: port disabled. ignoring.
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
end_request: I/O error, dev sdd, sector 0
unable to read partition table
sd 1:0:0:1: Attached scsi disk sdd
Vendor: IBM Model: Universal Xport Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdf: 62914560 512-byte hdwr sectors (32212 MB)
sdf: Write Protect is off
sdf: Mode Sense: 77 00 10 08
SCSI device sdf: drive cache: write back w/ FUA
SCSI device sdf: 62914560 512-byte hdwr sectors (32212 MB)
sdf: Write Protect is off
sdf: Mode Sense: 77 00 10 08
SCSI device sdf: drive cache: write back w/ FUA
sdf:end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
printk: 10 messages suppressed.
Buffer I/O error on device sde, logical block 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
Dev sde: unable to read RDB block 0
end_request: I/O error, dev sdf, sector 0
Dev sdf: unable to read RDB block 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
unable to read partition table
sd 0:0:1:0: Attached scsi disk sde
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdg: 157286400 512-byte hdwr sectors (80531 MB)
sdg: Write Protect is off
sdg: Mode Sense: 77 00 10 08
SCSI device sdg: drive cache: write back w/ FUA
SCSI device sdg: 157286400 512-byte hdwr sectors (80531 MB)
sdg: Write Protect is off
sdg: Mode Sense: 77 00 10 08
SCSI device sdg: drive cache: write back w/ FUA
sdg: unknown partition table
sd 0:0:1:1: Attached scsi disk sdg
Vendor: IBM Model: Universal Xport Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
end_request: I/O error, dev sdf, sector 0
unable to read partition table
sd 1:0:1:0: Attached scsi disk sdf
Vendor: IBM Model: 1814 FAStT Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdh: 157286400 512-byte hdwr sectors (80531 MB)
sdh: Write Protect is off
sdh: Mode Sense: 77 00 10 08
SCSI device sdh: drive cache: write back w/ FUA
SCSI device sdh: 157286400 512-byte hdwr sectors (80531 MB)
sdh: Write Protect is off
sdh: Mode Sense: 77 00 10 08
SCSI device sdh: drive cache: write back w/ FUA
sdh: unknown partition table
sd 1:0:1:1: Attached scsi disk sdh
Vendor: IBM Model: Universal Xport Rev: 0916
Type: Direct-Access ANSI SCSI revision: 05
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@xxxxxxxxxx
end_request: I/O error, dev sdb, sector 0
printk: 15 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
printk: 3 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
printk: 10 messages suppressed.
Buffer I/O error on device sdf, logical block 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdf, sector 62914432
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdf, sector 62914432
printk: 4 messages suppressed.
Buffer I/O error on device sdf, logical block 7864304
end_request: I/O error, dev sdf, sector 62914432
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sdd, sector 157286272
printk: 22 messages suppressed.
Buffer I/O error on device sdd, logical block 19660784
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 62914432
end_request: I/O error, dev sdf, sector 62914432
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdf, sector 0
printk: 30 messages suppressed.
Buffer I/O error on device sdf, logical block 0
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdb, sector 157286272
printk: 23 messages suppressed.
Buffer I/O error on device sdb, logical block 19660784
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1227304617.927:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1676 types, 213 bools, 1 sens, 1024 cats
security: 61 classes, 60092 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1227304618.084:3): policy loaded auid=4294967295
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.5.11-rh (June 4, 2007)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 98
eth0: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit
133MHz found at mem da000000, IRQ 98, node addr 001a64760068
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 19 (level, low) -> IRQ 82
eth1: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit
133MHz found at mem d8000000, IRQ 82, node addr 001a64760069
input: PC Speaker as /class/input/input2
tg3.c:v3.80-rh (August 2, 2007)
ACPI: PCI Interrupt 0000:0f:04.0[A] -> GSI 18 (level, low) -> IRQ 66
eth2: Tigon3 [partno(BCM95715s) rev 9003 PHY(5714)]
(PCIX:133MHz:64-bit) 1000Base-SX Ethernet 00:1a:64:76:00:6c
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth2: dma_rwctrl[76148000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:0f:04.1[B] -> GSI 19 (level, low) -> IRQ 82
eth3: Tigon3 [partno(BCM95715s) rev 9003 PHY(5714)]
(PCIX:133MHz:64-bit) 1000Base-SX Ethernet 00:1a:64:76:00:6e
eth3: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth3: dma_rwctrl[76148000] dma_mask[64-bit]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:1: Attached scsi generic sg2 type 0
scsi 0:0:0:31: Attached scsi generic sg3 type 0
sd 1:0:0:1: Attached scsi generic sg4 type 0
scsi 1:0:0:31: Attached scsi generic sg5 type 0
sd 0:0:1:0: Attached scsi generic sg6 type 0
sd 0:0:1:1: Attached scsi generic sg7 type 0
scsi 0:0:1:31: Attached scsi generic sg8 type 0
sd 1:0:1:0: Attached scsi generic sg9 type 0
sd 1:0:1:1: Attached scsi generic sg10 type 0
scsi 1:0:1:31: Attached scsi generic sg11 type 0
intel_rng: FWH not detected
Floppy drive(s): fd0 is 1.44M
end_request: I/O error, dev sdf, sector 62914432
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdf, sector 62914432
printk: 13 messages suppressed.
Buffer I/O error on device sdf, logical block 7864304
end_request: I/O error, dev sdd, sector 157286272
end_request: I/O error, dev sde, sector 62914432
end_request: I/O error, dev sdb, sector 157286272
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
floppy0: no floppy controllers found
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdd, sector 157286336
end_request: I/O error, dev sdf, sector 62914496
end_request: I/O error, dev sdb, sector 157286336
end_request: I/O error, dev sde, sector 62914496
end_request: I/O error, dev sdd, sector 157286384
end_request: I/O error, dev sdf, sector 62914544
end_request: I/O error, dev sdb, sector 157286384
end_request: I/O error, dev sde, sector 62914544
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
printk: 36 messages suppressed.
Buffer I/O error on device sdf, logical block 7864319
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
printk: 38 messages suppressed.
Buffer I/O error on device sdd, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
printk: 38 messages suppressed.
Buffer I/O error on device sde, logical block 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 37 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdf, sector 0
end_request: I/O error, dev sde, sector 0
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
end_request: I/O error, dev sdb, sector 157286392
printk: 2 messages suppressed.
Buffer I/O error on device sdb, logical block 19660799
end_request: I/O error, dev sdb, sector 157286392
Buffer I/O error on device sdb, logical block 19660799
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286136
end_request: I/O error, dev sdb, sector 157286136
end_request: I/O error, dev sdb, sector 8
end_request: I/O error, dev sdb, sector 8
end_request: I/O error, dev sdb, sector 157286384
end_request: I/O error, dev sdb, sector 157286384
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
printk: 9 messages suppressed.
Buffer I/O error on device sdb, logical block 19660799
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286336
end_request: I/O error, dev sdb, sector 157286336
end_request: I/O error, dev sdb, sector 157286144
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 19660768
end_request: I/O error, dev sdb, sector 157286144
end_request: I/O error, dev sdb, sector 157286144
end_request: I/O error, dev sdb, sector 157286144
end_request: I/O error, dev sdb, sector 157286384
end_request: I/O error, dev sdb, sector 157286384
end_request: I/O error, dev sdb, sector 157286000
end_request: I/O error, dev sdb, sector 157286000
end_request: I/O error, dev sdb, sector 157285664
end_request: I/O error, dev sdb, sector 157285664
end_request: I/O error, dev sdb, sector 157286392
printk: 9 messages suppressed.
Buffer I/O error on device sdb, logical block 19660799
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdb, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286136
end_request: I/O error, dev sdd, sector 157286136
end_request: I/O error, dev sdd, sector 8
printk: 9 messages suppressed.
Buffer I/O error on device sdd, logical block 1
end_request: I/O error, dev sdd, sector 8
end_request: I/O error, dev sdd, sector 157286384
end_request: I/O error, dev sdd, sector 157286384
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
printk: 8 messages suppressed.
Buffer I/O error on device sdd, logical block 19660799
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286336
end_request: I/O error, dev sdd, sector 157286336
end_request: I/O error, dev sdd, sector 157286144
end_request: I/O error, dev sdd, sector 157286144
end_request: I/O error, dev sdd, sector 157286144
end_request: I/O error, dev sdd, sector 157286144
end_request: I/O error, dev sdd, sector 157286384
end_request: I/O error, dev sdd, sector 157286384
printk: 9 messages suppressed.
Buffer I/O error on device sdd, logical block 19660798
end_request: I/O error, dev sdd, sector 157286000
end_request: I/O error, dev sdd, sector 157286000
end_request: I/O error, dev sdd, sector 157285664
end_request: I/O error, dev sdd, sector 157285664
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sdd, sector 157286392
end_request: I/O error, dev sde, sector 62914552
printk: 8 messages suppressed.
Buffer I/O error on device sde, logical block 7864319
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914296
end_request: I/O error, dev sde, sector 62914296
end_request: I/O error, dev sde, sector 8
end_request: I/O error, dev sde, sector 8
end_request: I/O error, dev sde, sector 62914544
end_request: I/O error, dev sde, sector 62914544
end_request: I/O error, dev sde, sector 62914552
printk: 9 messages suppressed.
Buffer I/O error on device sde, logical block 7864319
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914496
end_request: I/O error, dev sde, sector 62914496
end_request: I/O error, dev sde, sector 62914304
printk: 9 messages suppressed.
Buffer I/O error on device sde, logical block 7864288
end_request: I/O error, dev sde, sector 62914304
end_request: I/O error, dev sde, sector 62914304
end_request: I/O error, dev sde, sector 62914304
end_request: I/O error, dev sde, sector 62914544
end_request: I/O error, dev sde, sector 62914544
end_request: I/O error, dev sde, sector 62914160
end_request: I/O error, dev sde, sector 62914160
end_request: I/O error, dev sde, sector 62913824
end_request: I/O error, dev sde, sector 62913824
printk: 8 messages suppressed.
Buffer I/O error on device sde, logical block 7864228
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sde, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914296
end_request: I/O error, dev sdf, sector 62914296
printk: 9 messages suppressed.
Buffer I/O error on device sdf, logical block 7864287
end_request: I/O error, dev sdf, sector 8
end_request: I/O error, dev sdf, sector 8
end_request: I/O error, dev sdf, sector 62914544
end_request: I/O error, dev sdf, sector 62914544
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
printk: 9 messages suppressed.
Buffer I/O error on device sdf, logical block 7864319
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914496
end_request: I/O error, dev sdf, sector 62914496
end_request: I/O error, dev sdf, sector 62914304
end_request: I/O error, dev sdf, sector 62914304
end_request: I/O error, dev sdf, sector 62914304
end_request: I/O error, dev sdf, sector 62914304
end_request: I/O error, dev sdf, sector 62914544
printk: 8 messages suppressed.
Buffer I/O error on device sdf, logical block 7864318
end_request: I/O error, dev sdf, sector 62914544
end_request: I/O error, dev sdf, sector 62914160
end_request: I/O error, dev sdf, sector 62914160
end_request: I/O error, dev sdf, sector 62913824
end_request: I/O error, dev sdf, sector 62913824
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdf, sector 62914552
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdd, sector 0
end_request: I/O error, dev sde, sector 0
end_request: I/O error, dev sdf, sector 0
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1
extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/VolGroup00-LogVol00
100G 58G 37G 62% /
/dev/sda1 99M 32M 62M 34% /boot
tmpfs 2.0G 0 2.0G 0% /dev/shm
# fdisk -l
Disk /dev/sdc: 32.2 GB, 32212254720 bytes
255 heads, 63 sectors/track, 3916 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdc1 * 1 13 104391 83 Linux
/dev/sdc2 14 3916 31350847+ 8e Linux LVM
Disk /dev/sdh: 80.5 GB, 80530636800 bytes
255 heads, 63 sectors/track, 9790 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sdh doesn't contain a valid partition table
# cat /etc/fstab
/dev/VolGroup00/LogVol00 / ext3 defaults 1 1
LABEL=/boot /boot ext3 defaults 1 2
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
/dev/VolGroup00/LogVol01 swap swap defaults 0 0
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
