--- On Tue, 9/30/08, gary artim <gartim@xxxxxxxxx> wrote: > From: gary artim <gartim@xxxxxxxxx> > Subject: Adaptec 29160 Ultra160 problem -- Fedora 9 install. > To: fedora-list@xxxxxxxxxx > Date: Tuesday, September 30, 2008, 12:49 AM > Hi -- > > Installed fc9 on a server from fc8 and had a scsi > controller Adaptec > 29160 Ultra160 SCSI adapter > give me grief. It's used with an lto autochanger. When > I entered: > > mtx -d /dev/changer status > (/dev/changer a symlink to /dev/sg6) > > It hung for a while, (a huge listing follows, sorry about > this), then > kernel messages gallor. > > Anyway I tried reseating the card, moving the card to an > alternate > slot, checking the cabling, reboot the autochanger, > reboot the system --all did _not_ help. > > I pulled the card and replaced it with a Adaptec AIC-7892A > U160/m (rev > 02) and the autochanger and lto drive worked. > I also had to swap cables because of the interface > differences. > > Long story, but can anyone say that this card looks broken? > It has a 5 > year warranty and would like to get it replaced if so. Or > is > it a driver issue/I couldn't find a direct hit > searching the web or in > the archives? > > I think my head is still sore from banging it against the > autochanger! > Thanks for _any_ help! > > -- Gary > > Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX > PCI-X SCSI HBA > DRIVER, Rev 3.0 > Sep 27 10:30:15 genepi1 kernel: <Adaptec 29320ALP > PCIx Ultra320 > SCSI adapter> > Sep 27 10:30:15 genepi1 kernel: aic7901: Ultra320 > Wide Channel > A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs > Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt > 0000:04:01.0[A] -> > GSI 16 (level, low) -> IRQ 16 > Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0: > e1000_probe: > (PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54 > Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: > Sequential-Access HP > Ultrium 4-SCSI B12H PQ: 0 ANSI: 5 > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: > asynchronous > Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing > enabled. Depth 4 > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning > Domain Validation > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide > asynchronous > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160 > WIDE SCSI > 320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64) > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain > Validation > skipping write tests > Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending > Domain Validation > Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium > Changer > OVERLAND NEO Series 0504 PQ: 0 ANSI: 5 > Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing > enabled. Depth 4 > Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe: > Intel(R) > PRO/1000 Network Connection > Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent: > version 1.0.3 > Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl: > 4.13.0-ioctl > (2007-10-18) initialised: dm-devel@xxxxxxxxxx > Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath: > version 1.0.5 loaded > Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal > journal > Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on > /dev/sda2. > Priority:-1 extents:1 across:25165812k > Sep 27 10:30:15 genepi1 kernel: firmware: requesting > intel-ucode/06-0f-06 > Sep 27 10:30:15 genepi1 kernel: firmware: requesting > intel-ucode/06-0f-06 > Sep 27 10:30:15 genepi1 kernel: firmware: requesting > intel-ucode/06-0f-06 > Sep 27 10:30:15 genepi1 kernel: firmware: requesting > intel-ucode/06-0f-06 > Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update > Driver: v1.14a > <tigran@xxxxxxxxxxxxxxxxxxxx> > Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated > from revision > 0x44 to 0xcd, date = 09162007 > Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated > from revision > 0x44 to 0xcd, date = 09162007 > Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated > from revision > 0x44 to 0xcd, date = 09162007 > Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated > from revision > 0x44 to 0xcd, date = 09162007 > Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi > generic sg5 type 1 > Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi > generic sg6 type 8 > Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with > OnStream > support version 0.99.4 > Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73 > 2005/01/01 > 21:13:34 wriede Exp $ > Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs > updating - please > use bus_type methods > Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed > bufsize > 32768, s/g segs 256 > Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs > updating - please > use bus_type methods > Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi > tape st0 > Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct > i/o: yes > (alignment 4 B) > Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps > Full > Duplex, Flow Control: RX > Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE): > eth0: link > becomes ready > Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1: > link is not ready > Sep 27 10:54:58 genepi1 yum: Installed: > mtx-1.3.12-1.fc9.x86_64 > Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x010D): > Invalid field in CDB:. > Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to > queue an > ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0 > Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:02:27 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x34 Mode 0x22 > Sep 27 11:02:27 genepi1 kernel: Card was paused > Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel: > INTSTAT[0x0] > SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0] > Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x8] > Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:02:27 genepi1 kernel: > Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext = > 46 > Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2 > Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:02:27 genepi1 kernel: Pending list: > Sep 27 11:02:27 genepi1 kernel: 2 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:27 genepi1 kernel: 3 FIFO_USE[0x2] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:27 genepi1 kernel: Total 2 > Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0 > Sep 27 11:02:27 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list: > Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:02:27 genepi1 kernel: > Sep 27 11:02:27 genepi1 kernel: > Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x82a3, SCB 0x3 > Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:27 genepi1 kernel: > Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX > = 0x104, > DINDEX = 0x104 > Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:27 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted > from QINFIFO > Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to > queue an > ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:02:37 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x18 Mode 0x33 > kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:37 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x18 Mode 0x33 > Sep 27 11:02:37 genepi1 kernel: Card was paused > Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = > 46 > Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2 > Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:02:37 genepi1 kernel: Pending list: > Sep 27 11:02:37 genepi1 kernel: 2 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x2] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:37 genepi1 kernel: Total 2 > Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0 > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x82a3, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff, > SINDEX = 0x104, > DINDEX = 0x104 > Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel: > scsi5:0:1:0: Cmd > aborted from QINFIFO > Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue an > ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:02:37 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x31 Mode 0x11 > Sep 27 11:02:37 genepi1 kernel: Card was paused > Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = > 45 > Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 > Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:02:37 genepi1 kernel: Pending list: > Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:37 genepi1 kernel: Total 1 > Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0 > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x82a3, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX > = 0x104, > DINDEX = 0x104 > Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted > from QINFIFO > Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue an > ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted > from QINFIFO > Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue an > ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:02:37 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x31 Mode 0x11 > Sep 27 11:02:37 genepi1 kernel: Card was paused > Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = > 45 > Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 > Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:02:37 genepi1 kernel: Pending list: > Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:37 genepi1 kernel: Total 1 > Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0 > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x82a3, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: > Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX > = 0x104, > DINDEX = 0x104 > Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:37 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted > from QINFIFO > Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue an > ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:02:47 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x18 Mode 0x33 > Sep 27 11:02:47 genepi1 kernel: Card was paused > Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:02:47 genepi1 kernel: > Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext = > 45 > Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3 > Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:02:47 genepi1 kernel: Pending list: > Sep 27 11:02:47 genepi1 kernel: 3 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:02:47 genepi1 kernel: Total 1 > Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0 > Sep 27 11:02:47 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list: > Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:02:47 genepi1 kernel: > Sep 27 11:02:47 genepi1 kernel: > Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x82a3, SCB 0x3 > Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:47 genepi1 kernel: > Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff, > SINDEX = 0x104, > DINDEX = 0x104 > Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:02:47 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted > from QINFIFO > Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to > queue a > TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0 > Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code > sleeping > Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer > expired (active 1) > Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset > returning 0x2003 > Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue a > TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0 > Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code > sleeping > Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer > expired (active 1) > Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset > returning 0x2003 > Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes > Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes > Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to > queue an > ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:03:17 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x9 Mode 0x33 > Sep 27 11:03:17 genepi1 kernel: Card was paused > Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:03:17 genepi1 kernel: > Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext = > 45 > Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2 > Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:03:17 genepi1 kernel: Pending list: > Sep 27 11:03:17 genepi1 kernel: 2 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:03:17 genepi1 kernel: Total 1 > Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0 > Sep 27 11:03:17 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list: > Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:03:17 genepi1 kernel: > Sep 27 11:03:17 genepi1 kernel: > Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x80a3, SCB 0x3 > Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:03:17 genepi1 kernel: > Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff, > SINDEX = 0x104, > DINDEX = 0x104 > Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:03:17 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted > from QINFIFO > Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to > queue an > ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery, > card was not paused > Sep 27 11:03:27 genepi1 kernel: > >>>>>>>>>>>>>>>>>> > Dump Card State > Begins > <<<<<<<<<<<<<<<<< > Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State > at program > address 0x22 Mode 0x33 > Sep 27 11:03:27 genepi1 kernel: Card was paused > Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] > SELID[0x10] > HS_MAILBOX[0x0] > Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80] > SEQINTSTAT[0x0] > SAVED_MODE[0x11] DFFSTAT[0x33] > Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0] > SCSIPHASE[0x0] > SCSIBUS[0x0] LASTPHASE[0x1] > Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0] > SCSISEQ1[0x12] > SEQCTL0[0x0] SEQINTCTL[0x0] > Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0] > SEQ_FLAGS2[0x4] > QFREEZE_COUNT[0x7] > Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] > MK_MESSAGE_SCB[0xff00] > Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] > SSTAT0[0x0] SSTAT1[0x0] > Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] > PERRDIAG[0x0] > SIMODE1[0xa4] > Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0] > LQISTAT2[0x0] LQOSTAT0[0x0] > Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0] > LQOSTAT2[0xe1] > Sep 27 11:03:27 genepi1 kernel: > Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING > = 0 LASTSCB > 0xffff CURRSCB 0x3 NEXTSCB 0xff80 > Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext = > 45 > Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2 > Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES: > Sep 27 11:03:27 genepi1 kernel: Pending list: > Sep 27 11:03:27 genepi1 kernel: 2 FIFO_USE[0x0] > SCB_CONTROL[0x68] > SCB_SCSIID[0x17] > Sep 27 11:03:27 genepi1 kernel: Total 1 > Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0 > Sep 27 11:03:27 genepi1 kernel: Sequencer Complete > DMA-inprog list: > Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list: > Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and > Complete list: > Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and > Complete list: > Sep 27 11:03:27 genepi1 kernel: > Sep 27 11:03:27 genepi1 kernel: > Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP > == 0x80a3, SCB 0x3 > Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, > HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:03:27 genepi1 kernel: > Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP > == 0x8063, SCB 0x3 > Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f] > SEQINTSRC[0x0] > DFCNTRL[0x0] DFSTATUS[0x89] > Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] > SG_STATE[0x0] > DFFSXFRCTL[0x0] > Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] > SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 > 0x1 0x0 0x0 > 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 > Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0, > LQOSTATE = 0x0, > OPTIONMODE = 0x52 > Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 > MAXCMDCNT = 0x1 > Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 > SAVED_LUN = 0x0 > Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc] > Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0] > Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff, > SINDEX = 0x104, > DINDEX = 0x104 > Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3, > SCB_NEXT == > 0xff80, SCB_NEXT2 == 0xff80 > Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c > Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0 > 0x0 0x0 0x0 > Sep 27 11:03:27 genepi1 kernel: > <<<<<<<<<<<<<<<<< > Dump Card State Ends > >>>>>>>>>>>>>>>>>> > Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted > from QINFIFO > Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined > - not > ready after error recovery > Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device > offlined - not > ready after error recovery > Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x010D): > Invalid field in CDB:. > Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x010D): > Invalid field in CDB:. > Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x010D): > Invalid field in CDB:. > Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: > (0x03:0x0101): > Invalid command opcode:opcode=0xB8. > 27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = > 0x00, SHCNT = 0x0 > Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 > CCSGCTL[0x10] > Sep 27 11:03:27 genepi1 kernel: > My Adaptec 29160 Ultra160 comes with testing software shown early in boot! Next comes grub > -- > fedora-list mailing list > fedora-list@xxxxxxxxxx > To unsubscribe: > https://www.redhat.com/mailman/listinfo/fedora-list > Guidelines: > http://fedoraproject.org/wiki/Communicate/MailingListGuidelines -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
