I lose my network after every re-boot.
I have the same thing happening on my AMD desktop box and my iBook G4.
I can get it back up with the nice GUI network tool, just by hitting
the enable button. Then it works.
Then I reboot and it doesn't work, until I click that button in the
GUI network tool again.
I just tried the Save item in the File menu of the Network Settings
tool. Rebooted and the interface is still down. But this time, when I
try to bring up the Network Settings tool, I get a message dialog,
about trying to bring the interface up, which goes away after a
second or two, to be replaced with an error dialog about being unable
to bring the interface up. (I went and logged in in Japanese again,
so I'm translating.) So, I select eth0, hit the green button, and
ping a box in the local network, and mail ships me my dmesg like I
asked.
Shouldn't be hardware issues -- I'm dual-booting Mac OS X with no
network problems, and I netinstalled the box via the built-in nic.
I'm assuming that the results of using the GUI interfaces to the
network is supposed to be sticky. Is my assumption there wrong?
I seem to be too clueless to know where to look. Anyone got a clue
for me?
Here's my /etc/sysconfig/network-scripts/ifcfg-eth0 (after bringing
up the interface, with internal details obfuscated/effaced):
-------------------------------
# Apple Computer Inc. UniNorth 2 GMAC (Sun GEM)
DEVICE=eth0
BOOTPROTO=none
BROADCAST=172.19.255.255
HWADDR=**:**:**:**:**:**
IPADDR=172.19.36.26
NETMASK=255.255.0.0
NETWORK=172.19.0.0
ONBOOT=yes
DNS1=**.**.**.**
DNS2=**.**.**.**
SEARCH="reiisi.homedns.org"
NM_CONTROLLED=no
GATEWAY=172.19.138.95
TYPE=Ethernet
USERCTL=no
PEERDNS=yes
IPV6INIT=no
--------------------------------
my /etc/hosts:
--------------------------------
# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1 moth.reiisi.homedns.org moth
::1 localhost6.localdomain6 localhost6
172.19.36.24 reiisi.homedns.org reiisi
172.19.36.25 federales.reiisi.homedns.org federales
--------------------------------
and my dmesg:
--------------------------------
Using PowerMac machine description
Total memory = 768MB; using 2048kB for hash table (at cfe00000)
Initializing cgroup subsys cpu
Linux version 2.6.25-14.fc9.ppc (mockbuild@) (gcc version 4.3.0
20080428 (Red Hat 4.3.0-8) (GCC) ) #1 Thu May 1 05:51:33 EDT 2008
Found initrd at 0xc1a00000:0xc1da7800
Found UniNorth memory controller & host bridge @ 0xf8000000 revision:
0xd2
Mapped at 0xfdfc0000
Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000
Processor NAP mode on idle enabled.
PowerMac motherboard: iBook G4
via-pmu: Server Mode is disabled
PMU driver v2 initialized for Core99, firmware: 0c
console [udbg0] enabled
Entering add_active_range(0, 0, 196608) 0 entries of 256 used
Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus
number: 0->0
PCI host bridge /pci@f0000000 ranges:
MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000
IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000
MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000
Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus
number: 0->0
PCI host bridge /pci@f2000000 (primary) ranges:
MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000
IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000
MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000
Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus
number: 0->0
PCI host bridge /pci@f4000000 ranges:
MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000
IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000
nvram: Checking bank 0...
nvram: gen0=292, gen1=291
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
Top of RAM: 0x30000000, Total RAM: 0x30000000
Memory hole size: 0MB
Zone PFN ranges:
DMA 0 -> 196608
Normal 196608 -> 196608
HighMem 196608 -> 196608
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 196608
On node 0 totalpages: 196608
DMA zone: 1536 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 195072 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
195072
Kernel command line: ro rhgb quiet root=UUID=<long_ identifier>
mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 64, shift: 6, mask: 3f
mpic: Initializing for 64 sources
PID hash table entries: 4096 (order: 12, 16384 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 18.432000 MHz
time_init: processor frequency = 1199.999997 MHz
clocksource: timebase mult[d9038e4] shift[22] registered
clockevent: decrementer mult[4b7] shift[16] cpu[0]
Console: colour dummy device 80x25
console handover: boot [udbg0] -> real [tty0]
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
High memory: 0k
Memory: 768000k/786432k available (4288k kernel code, 17972k
reserved, 164k data, 342k bss, 232k init)
SLUB: Genslabs=12, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay loop... 36.73 BogoMIPS (lpj=18368)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
device-tree: Duplicate name in /cpus/PowerPC,G4@0, renamed to "l2-
cache#1"
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
net_namespace: 540 bytes
NET: Registered protocol family 16
KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
channel 0 bus <multibus>
channel 1 bus <multibus>
KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000
channel 0 bus <multibus>
PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c
channel 1 bus <multibus>
channel 2 bus <multibus>
PCI: Probing PCI hardware
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3742k freed
Thermal assist unit not available
Registering PowerMac CPU frequency driver
Low: 599 Mhz, High: 1199 Mhz, Boot: 599 Mhz
audit: initializing netlink socket (disabled)
type=2000 audit(***.***:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
radeonfb (0000:00:10.0): Invalid ROM signature 0 should be 0xaa55
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz,
System=183.00 MHz
radeonfb: PLL min 12000 max 35000
i2c-adapter i2c-2: unable to read EDID block.
i2c-adapter i2c-2: unable to read EDID block.
i2c-adapter i2c-2: unable to read EDID block.
i2c-adapter i2c-3: unable to read EDID block.
i2c-adapter i2c-3: unable to read EDID block.
i2c-adapter i2c-3: unable to read EDID block.
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Using Firmware dividers 0x000600ad from PPLL 0
radeonfb: Dynamic Clock Power Management enabled
Console: switching to colour frame buffer device 128x48
radeonfb: Backlight initialized (radeonbl0)
radeonfb (0000:00:10.0): ATI Radeon \c
Macintosh non-volatile memory driver v1.1
Linux agpgart interface v0.103
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 8
agpgart: AGP aperture is 32M @ 0x0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Serial: MPC52xx PSC UART driver
brd: module loaded
MacIO PCI driver attached to Intrepid chipset
input: Macintosh mouse button emulation as /devices/virtual/input/input0
apm_emu: PMU APM Emulation initialized.
adb: starting probe task...
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PCI: Enabling device 0002:20:0d.0 (0000 -> 0002)
adb devices: [2]: 2 c9 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type JIS.
input: ADB keyboard as /devices/virtual/input/input1
input: ADB Powerbook buttons as /devices/virtual/input/input2
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse as /devices/virtual/input/input3
adb: finished probe task...
ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
Probing IDE interface ide0...
hda: Hitachi HTS541616J9AT00, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
ide0 at 0xf102a000-0xf102a007,0xf102a160 on irq 39
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: MWDMA2 mode selected
ide1 at 0xf1014000-0xf1014007,0xf1014160 on irq 24
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/7512KiB Cache, CHS=19457/255/63
hda: cache flushes supported
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11
hda12 hda13 hda14
mice: PS/2 mouse device common for all mice
platform ppc-rtc.0: rtc core: registered ppc_md as rtc0
PowerMac i2c bus pmu 2 registered
PowerMac i2c bus pmu 1 registered
PowerMac i2c bus mac-io 0 registered
PowerMac i2c bus uni-n 1 registered
PowerMac i2c bus uni-n 0 registered
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
input: PMU as /devices/virtual/input/input4
Registered led device: pmu-front-led
Freeing unused kernel memory: 232k init
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
ehci_hcd 0001:10:1b.2: EHCI Host Controller
ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000
ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25-14.fc9.ppc ehci_hcd
usb usb1: SerialNumber: 0001:10:1b.2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
Apple USB OHCI 0001:10:18.0 disabled by firmware
Apple USB OHCI 0001:10:19.0 disabled by firmware
PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
ohci_hcd 0001:10:1a.0: OHCI Host Controller
ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25-14.fc9.ppc ohci_hcd
usb usb2: SerialNumber: 0001:10:1a.0
PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
ohci_hcd 0001:10:1b.0: OHCI Host Controller
ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25-14.fc9.ppc ohci_hcd
usb usb3: SerialNumber: 0001:10:1b.0
PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
ohci_hcd 0001:10:1b.1: OHCI Host Controller
ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4
ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25-14.fc9.ppc ohci_hcd
usb usb4: SerialNumber: 0001:10:1b.1
USB Universal Host Controller Interface driver v3.0
usb 3-1: new low speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
input: ELECOM ELECOM USB Mouse with Wheel as /devices/
pci0001:10/0001:10:1b.0/usb3/3-1/3-1:1.0/input/input5
input,hidraw0: USB HID v1.00 Mouse [ELECOM ELECOM USB Mouse with
Wheel] on usb-0001:10:1b.0-1
usb 3-1: New USB device found, idVendor=056e, idProduct=000f
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: ELECOM USB Mouse with Wheel
usb 3-1: Manufacturer: ELECOM
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-
devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
type=1404 audit(***.***:2): enforcing=1 old_enforcing=0 auid=*** ses=***
SELinux:8192 avtab hash slots allocated. Num of rules:172315
SELinux:8192 avtab hash slots allocated. Num of rules:172315
security: 8 users, 12 roles, 2301 types, 116 bools, 1 sens, 1024 cats
security: 72 classes, 172315 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses
genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses
genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses
genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=allow
type=1403 audit(***.***:3): policy loaded auid=*** ses=***
PCI: Enabling device 0001:10:12.0 (0004 -> 0006)
ssb: Sonics Silicon Backplane found on PCI device 0001:10:12.0
PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
firewire_ohci: Added fw-ohci device 0002:20:0e.0, OHCI version 1.10
firewire_core: created device fw0: GUID ***, S400
sungem.c:v0.98 8/24/03 David S. Miller (davem@xxxxxxxxxx)
PHY ID: 4061e4, addr: 0
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:47:8a:4e
eth0: Found BCM5221 PHY
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
eth0: Link is up at 100 Mbps, full-duplex.
pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>)
ttyPZ0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyPZ1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
b43-phy0: Broadcom 4306 WLAN found
b43-phy0 debug: Found PHY: Analog 2, Type 2, Revision 2
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
device-mapper: multipath: version 1.0.5 loaded
loop: module loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-1, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-2, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-3, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-4, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-5, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-6, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-7, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda4, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.28.0 20060524 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
Adding 2097144k swap on /dev/mapper/F9VolGrP-f9swap. Priority:-1
extents:1 across:2097144k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
genfs_contexts
ip6_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (12288 buckets, 49152 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses
genfs_contexts
fuse init (API version 7.9)
SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
SCSI subsystem initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
input: b43-phy0 as /devices/virtual/input/input6
b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/
Drivers/b43#devicefirmware and download the latest firmware (version 4).
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
ufs was compiled with read-only support, can't be mounted as read-write
ufs was compiled with read-only support, can't be mounted as read-write
SELinux: initialized (dev hda6, type hfsplus), uses genfs_contexts
SELinux: initialized (dev hda3, type hfsplus), uses genfs_contexts
SELinux: initialized (dev hda10, type hfsplus), uses genfs_contexts
hfs: write access to a jounaled filesystem is not supported, use the
force option at your own risk, mounting read-only.
SELinux: initialized (dev hda5, type hfsplus), uses genfs_contexts
SELinux: initialized (dev hda8, type hfsplus), uses genfs_contexts
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
eth0: no IPv6 routers present
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
