I just popped another 2GB in my development machine, 2GB to 4GB RAM,
and only 3GB shows. Yes I looked at the 820 output, yes I tried PAE
kernels, yes I checked the BIOS to see the the hole options were
tried, other thoughts.
FC6 running 2.6.22.14-72.fc6PAE, also 2.6.24.4 kernel.org build.
dmesg hopefully attached if it doesn't get stripped again.
--
Bill Davidsen <davidsen@xxxxxxx>
"We have more to fear from the bungling of the incompetent than from
the machinations of the wicked." - from Slashdot
Linux version 2.6.22.14-72.fc6PAE
(brewbuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2
20070626 (Red Hat 4.1.2-13)) #1 SMP Wed Nov 21 14:39:09 EST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000c77a0000 (usable)
BIOS-e820: 00000000c77a0000 - 00000000c77ae000 (ACPI data)
BIOS-e820: 00000000c77ae000 - 00000000c77e0000 (ACPI NVS)
BIOS-e820: 00000000c77e0000 - 00000000c7800000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
2295MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 817056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 817056
early_node_map[1] active PFN ranges
0: 0 -> 817056
On node 0 totalpages: 817056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 4591 pages used for memmap
HighMem zone: 583089 pages, LIFO batch:31
DMI 2.4 present.
Using APIC driver default
ACPI: RSDP 000FA5D0, 0014 (r0 ACPIAM)
ACPI: RSDT C77A0000, 0038 (r1 A M I OEMRSDT 10000627 MSFT 97)
ACPI: FACP C77A0200, 0081 (r1 A M I OEMFACP 10000627 MSFT 97)
ACPI: DSDT C77A0410, 4AEA (r1 A0281 A0281074 74 INTL 2002026)
ACPI: FACS C77AE000, 0040
ACPI: APIC C77A0390, 0080 (r1 A M I OEMAPIC 10000627 MSFT 97)
ACPI: OEMB C77AE040, 006B (r1 A M I AMI_OEM 10000627 MSFT 97)
ACPI: MCFG C77A4F00, 003C (r1 A M I OEMMCFG 10000627 MSFT 97)
ACPI: ASF! C77A4F3C, 0099 (r32 LEGEND I865PASF 1 INTL 2002026)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c8000000 (gap: c7800000:38380000)
Built 1 zonelists. Total pages: 810673
Kernel command line: ro root=/dev/VG01/Root32 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07cf000 soft=c07af000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2394.031 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3233428k/3268224k available (2259k kernel code, 33464k
reserved, 1202k data, 268k init, 2350720k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
vmalloc : 0xf8800000 - 0xff9fe000 ( 113 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0767000 - 0xc07aa000 ( 268 kB)
.data : 0xc0634d7c - 0xc0761584 (1202 kB)
.text : 0xc0400000 - 0xc0634d7c (2259 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 4789.91 BogoMIPS
(lpj=2394957)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000
00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00003940
0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07d0000 soft=c07b0000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4787.24 BogoMIPS
(lpj=2393620)
CPU: After generic identify, caps: bfebfbff 20000000 00000000
00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00003940
0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9577.15 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time: 19:52:01 Date: 03/16/108
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:08: ioport range 0x290-0x297 has been reserved
pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:10: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:10: iomem range 0xc0000-0xdffff could not be reserved
pnp: 00:10: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:10: iomem range 0x100000-0xc77fffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:1c.0
IO window: e000-efff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: d000-dfff
MEM window: cff00000-cfffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: b000-cfff
MEM window: cfe00000-cfefffff
PREFETCH window: c8000000-c80fffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2372k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1208375521.368:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key CAA333178AF1EC5F
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Warning (tbutils-0217): Incorrect checksum in table [SSDT]
- 0E, should be 15 [20070126]
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB]
- A6, should be 99 [20070126]
ACPI: SSDT C77A4FE0, 02E3 (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: SSDT C77A52D0, 02DA (r1 AMI CPU2PM 1 INTL 20060113)
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device
is not present [20070126]
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device
is not present [20070126]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: DVDRW DRW-3S163, ATAPI CD/DVD-ROM drive
hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
IT8212: IDE controller at PCI slot 0000:01:04.0
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 19 (level, low) -> IRQ 19
IT8212: chipset revision 17
it821x: controller in pass through mode.
IT8212: 100% native mode on irq 19
ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xb408-0xb40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
ide-floppy driver 0.99.newide
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
atkbd.c: Failed to enable keyboard on isa0060/serio0
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 4:544:900
hash matches device PNP0501:00
Freeing unused kernel memory: 268k freed
Write protecting the kernel read-only data: 925k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xcfdffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 8852.000 MB/sec
raid5: using function: pIII_sse (8852.000 MB/sec)
input: PS/2 Generic Mouse as /class/input/input2
raid6: int32x1 898 MB/s
raid6: int32x2 976 MB/s
raid6: int32x4 890 MB/s
raid6: int32x8 804 MB/s
raid6: mmxx1 3042 MB/s
raid6: mmxx2 3445 MB/s
raid6: sse1x1 1855 MB/s
raid6: sse1x2 2640 MB/s
raid6: sse2x1 3593 MB/s
raid6: sse2x2 4312 MB/s
raid6: using algorithm sse2x2 (4312 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
SCSI subsystem initialized
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x0001a800 ctl 0x0001a402 bmdma 0x00019400 irq 17
ata2: SATA max UDMA/133 cmd 0x0001a000 ctl 0x00019802 bmdma 0x00019408 irq 17
usb 1-1: device not accepting address 2, error -71
ata1.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.01: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata1.01: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata1.01: configured for UDMA/133
ata2.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.01: ATA-7: ST3320620NS, 3.AEG, max UDMA/133
ata2.01: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
ata2.01: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 0:0:1:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 0:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 0:0:1:0: [sdb] Attached SCSI disk
scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 >
sd 1:0:0:0: [sdc] Attached SCSI disk
scsi 1:0:1:0: Direct-Access ATA ST3320620NS 3.AE PQ: 0 ANSI: 5
sd 1:0:1:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:1:0: [sdd] Write Protect is off
sd 1:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:1:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:1:0: [sdd] Write Protect is off
sd 1:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdd: unknown partition table
sd 1:0:1:0: [sdd] Attached SCSI disk
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@xxxxxxxxxx
md: Autodetecting RAID arrays.
usb 5-4: new high speed USB device using ehci_hcd and address 4
md: autorun ...
md: considering sdc7 ...
md: adding sdc7 ...
md: sdc6 has different UUID to sdc7
md: sdc5 has different UUID to sdc7
md: sdc3 has different UUID to sdc7
md: sdc2 has different UUID to sdc7
md: sdc1 has different UUID to sdc7
md: adding sdb7 ...
md: sdb6 has different UUID to sdc7
md: sdb5 has different UUID to sdc7
md: sdb3 has different UUID to sdc7
md: sdb2 has different UUID to sdc7
md: sdb1 has different UUID to sdc7
md: adding sda7 ...
md: sda6 has different UUID to sdc7
md: sda5 has different UUID to sdc7
md: sda3 has different UUID to sdc7
md: sda2 has different UUID to sdc7
md: sda1 has different UUID to sdc7
md: created md6
md: bind<sda7>
md: bind<sdb7>
md: bind<sdc7>
md: running: <sdc7><sdb7><sda7>
md: personality for level 0 is not loaded!
md: do_md_run() returned -22
md: md6 stopped.
md: unbind<sdc7>
md: export_rdev(sdc7)
md: unbind<sdb7>
md: export_rdev(sdb7)
md: unbind<sda7>
md: export_rdev(sda7)
md: considering sdc6 ...
md: adding sdc6 ...
md: sdc5 has different UUID to sdc6
md: sdc3 has different UUID to sdc6
md: sdc2 has different UUID to sdc6
md: sdc1 has different UUID to sdc6
md: adding sdb6 ...
md: sdb5 has different UUID to sdc6
md: sdb3 has different UUID to sdc6
md: sdb2 has different UUID to sdc6
md: sdb1 has different UUID to sdc6
md: adding sda6 ...
md: sda5 has different UUID to sdc6
md: sda3 has different UUID to sdc6
md: sda2 has different UUID to sdc6
md: sda1 has different UUID to sdc6
md: created md4
md: bind<sda6>
md: bind<sdb6>
md: bind<sdc6>
md: running: <sdc6><sdb6><sda6>
md: personality for level 1 is not loaded!
md: do_md_run() returned -22
md: md4 stopped.
md: unbind<sdc6>
md: export_rdev(sdc6)
md: unbind<sdb6>
md: export_rdev(sdb6)
md: unbind<sda6>
md: export_rdev(sda6)
md: considering sdc5 ...
md: adding sdc5 ...
md: sdc3 has different UUID to sdc5
md: sdc2 has different UUID to sdc5
md: sdc1 has different UUID to sdc5
md: adding sdb5 ...
md: sdb3 has different UUID to sdc5
md: sdb2 has different UUID to sdc5
md: sdb1 has different UUID to sdc5
md: adding sda5 ...
md: sda3 has different UUID to sdc5
md: sda2 has different UUID to sdc5
md: sda1 has different UUID to sdc5
md: created md3
md: bind<sda5>
md: bind<sdb5>
md: bind<sdc5>
md: running: <sdc5><sdb5><sda5>
md: md3: raid array is not clean -- starting background reconstruction
raid5: device sdc5 operational as raid disk 2
raid5: device sdb5 operational as raid disk 1
raid5: device sda5 operational as raid disk 0
raid5: allocated 3163kB for md3
raid5: raid level 5 set md3 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda5
disk 1, o:1, dev:sdb5
disk 2, o:1, dev:sdc5
md3: bitmap initialized from disk: read 15/15 pages, set 5 bits, status: 0
created bitmap (235 pages) for device md3
md: considering sdc3 ...
md: adding sdc3 ...
md: sdc2 has different UUID to sdc3
md: sdc1 has different UUID to sdc3
md: adding sdb3 ...
md: sdb2 has different UUID to sdc3
md: sdb1 has different UUID to sdc3
md: adding sda3 ...
md: resync of RAID array md3
md: sda2 has different UUID to sdc3
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than
200000 KB/sec) for resync.
md: sda1 has different UUID to sdc3
md: using 128k window, over a total of 30716160 blocks.
md: created md2
md: bind<sda3>
md: bind<sdb3>
md: bind<sdc3>
md: running: <sdc3><sdb3><sda3>
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: device sda3 operational as raid disk 0
raid5: allocated 3163kB for md2
raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
md: considering sdc2 ...
md: adding sdc2 ...
md: sdc1 has different UUID to sdc2
md: adding sdb2 ...
md: sdb1 has different UUID to sdc2
md: adding sda2 ...
md: sda1 has different UUID to sdc2
md: created md1
md: bind<sda2>
md: bind<sdb2>
md: bind<sdc2>
md: running: <sdc2><sdb2><sda2>
raid5: device sdc2 operational as raid disk 2
raid5: device sdb2 operational as raid disk 1
raid5: device sda2 operational as raid disk 0
raid5: allocated 3163kB for md1
raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda2
disk 1, o:1, dev:sdb2
disk 2, o:1, dev:sdc2
md: considering sdc1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: running: <sdc1><sdb1><sda1>
md: personality for level 1 is not loaded!
md: do_md_run() returned -22
md: md0 stopped.
md: unbind<sdc1>
md: export_rdev(sdc1)
md: unbind<sdb1>
md: export_rdev(sdb1)
md: unbind<sda1>
md: export_rdev(sda1)
md: ... autorun DONE.
md: Autodetecting RAID arrays.
usb 5-4: configuration #1 chosen from 1 choice
md: md3: resync done.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: adding sdb1 ...
md: adding sdc1 ...
md: sda6 has different UUID to sda1
md: sdb6 has different UUID to sda1
md: sdc6 has different UUID to sda1
md: sda7 has different UUID to sda1
md: sdb7 has different UUID to sda1
md: sdc7 has different UUID to sda1
md: created md0
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: running: <sda1><sdb1><sdc1>
md: personality for level 1 is not loaded!
md: do_md_run() returned -22
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: unbind<sdb1>
md: export_rdev(sdb1)
md: unbind<sdc1>
md: export_rdev(sdc1)
md: considering sda6 ...
md: adding sda6 ...
md: adding sdb6 ...
md: adding sdc6 ...
md: sda7 has different UUID to sda6
md: sdb7 has different UUID to sda6
md: sdc7 has different UUID to sda6
md: created md4
md: bind<sdc6>
md: bind<sdb6>
md: bind<sda6>
md: running: <sda6><sdb6><sdc6>
md: personality for level 1 is not loaded!
md: do_md_run() returned -22
md: md4 stopped.
md: unbind<sda6>
md: export_rdev(sda6)
md: unbind<sdb6>
md: export_rdev(sdb6)
md: unbind<sdc6>
md: export_rdev(sdc6)
md: considering sda7 ...
md: adding sda7 ...
md: adding sdb7 ...
md: adding sdc7 ...
md: created md6
md: bind<sdc7>
md: bind<sdb7>
md: bind<sda7>
md: running: <sda7><sdb7><sdc7>
md: personality for level 0 is not loaded!
md: do_md_run() returned -22
md: md6 stopped.
md: unbind<sda7>
md: export_rdev(sda7)
md: unbind<sdb7>
md: export_rdev(sdb7)
md: unbind<sdc7>
md: export_rdev(sdc7)
md: ... autorun DONE.
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda5
disk 1, o:1, dev:sdb5
disk 2, o:1, dev:sdc5
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
hiddev96: USB HID v1.10 Device [CPS UPS BF700] on usb-0000:00:1d.0-1
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 6 roles, 1676 types, 213 bools, 1 sens, 1024 cats
security: 61 classes, 58427 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses
genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1208375536.507:2): policy loaded auid=4294967295
iTCO_vendor_support: vendor-support=0
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4
if 1 alt 0 proto 2 vid 0x04B8 pid 0x0838
drivers/usb/class/usblp.c: usblp1: USB Bidirectional printer dev 2
if 0 alt 1 proto 2 vid 0x03F0 pid 0x1D17
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 1:0:1:0: Attached scsi generic sg3 type 0
e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1)
00:17:31:5c:57:c0
intel_rng: FWH not detected
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
lp0: using parport0 (interrupt-driven).
lp0: console ready
sonypi: Sony Programmable I/O Controller Driver v1.26.
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
scsi 2:0:0:0: Direct-Access EPSON Stylus Storage 1.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sde] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
No dock devices found.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdc7 ...
md: adding sdc7 ...
md: adding sdb7 ...
md: adding sda7 ...
md: sdc6 has different UUID to sdc7
md: sdb6 has different UUID to sdc7
md: sda6 has different UUID to sdc7
md: sdc1 has different UUID to sdc7
md: sdb1 has different UUID to sdc7
md: sda1 has different UUID to sdc7
md: created md6
md: bind<sda7>
md: bind<sdb7>
md: bind<sdc7>
md: running: <sdc7><sdb7><sda7>
md: raid0 personality registered for level 0
md6: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdc7
raid0: comparing sdc7(3911680) with sdc7(3911680)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb7
raid0: comparing sdb7(3911680) with sdc7(3911680)
raid0: EQUAL
raid0: looking at sda7
raid0: comparing sda7(3911680) with sdc7(3911680)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 11735040 blocks.
raid0 : conf->hash_spacing is 11735040 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: considering sdc6 ...
md: adding sdc6 ...
md: adding sdb6 ...
md: adding sda6 ...
md: sdc1 has different UUID to sdc6
md: sdb1 has different UUID to sdc6
md: sda1 has different UUID to sdc6
md: created md4
md: bind<sda6>
md: bind<sdb6>
md: bind<sdc6>
md: running: <sdc6><sdb6><sda6>
md: raid1 personality registered for level 1
raid1: raid set md4 active with 3 out of 3 mirrors
md: considering sdc1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: running: <sdc1><sdb1><sda1>
raid1: raid set md0 active with 3 out of 3 mirrors
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev md0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-1, type ext3), uses xattr
Adding 2039800k swap on /dev/md1. Priority:-1 extents:1 across:2039800k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX/TX
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
ip6_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
